Search Documents

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By H. S. Puttanna

Bound water plays an important role in the processing and utilization of numerous materials and mineral processing systems. The fundamental nature of this near surface bound (vicinal) water is yet to be understood in its complete detail. The objective of this paper is to use dielectric measurements to characterize the bound water near hydrophobic and hydrophilic oxide surfaces. It is anticipated that a combination of dielectric property measurements and characteristic relaxation times will allow for more effective analysis of the interfacial water.

Jan 1, 1992

By R. Q. Phillips

INTRODUCTION Since Canada commenced sulphur exports in the early 1960's, the volume of exports has grown steadily and by 1984 Canadian sulphur accounted for 45% of internationally traded sulphur. In 1984 a total of 7.6 million tonnes of Canadian sulphur was shipped to offshore markets and the U.S.A. Total shipments, including domestic sales, were 8.3 million tonnes. With a production of some 5.6 million tonnes, inventory was drawn down by nearly 3 million tonnes in order to keep pace with demand. Since 1979, world consumption has exceeded total world production and Canadian sulphur inventory has played a truly crucial role in balancing world supply and demand. Consequently, by the end of 1984 the Canadian inventory, which stood at 21 million tonnes in 1978, had been almost halved to 12 million tonnes. This inventory, however, is still by far the largest in the world and will continue to play a vital role in the world supply until expected depletion around 1990. Canada is the world's second largest producer of sulphur following the U.S.A.. The Current production level of between 5 and 6 million tonnes per annum is forecast to be maintained to 1990 with only a marginal fall in that production level in the following decade to the year 2000. This will ensure that Canada retains its position as one of the largest producers and most important suppliers of sulphur in the world market well into the future. CANADA AS WORLD SUPPLIER OF SULPHUR Since Canada commenced sulphur exports in the early 19601s, exports have grown steadily. (Figure 1) The rate of growth accelerated in recent years and in 1984 a total of 7.6 million tonnes was sold for export, compared to 3.0 million tonnes in 1975 and less than 1 million tonnes in 1964. World trade in sulphur also increased during this period, from 11 million tonnes in 1975 to 17.0 million tonnes in 1984 (Figure 2). Most of this increase in volume was accounted for by Canada and Poland. As a result, the importance of Canada as world supplier expanded from 28% in 1975 to 45% in 1984. The markets for Canadian sulphur can be divided into two broad categories, i.e., solid and liquid (Figure 3). The solid market is the largest, taking about 70% of Canadian output, virtually all of which is sold offshore. The U.S.A. and the Canadian domestic market take about 20% and 10% respectively, in liquid form. In 1984, (figure 4) total Canadian sulphur sales exceeded 8 million tonnes with offshore export sales at a record 5.8 million tonnes and sales to the U.S. of 1.8 million tonnes. Domestic sales accounted for only 0.7 million tonnes. The general trend for offshore export sales has been upward whereas there has been relative stability in domestic sales. The exceptional growth in offshore sales in the 1970's necessitated considerable capital investments by the industry in order to establish a logistics system capable of handling increasing offshore tonnages. Over 50 sulphur plants are currently operating in Alberta and British Columbia. Some of these are connected by rail, (Figure 5) the balance being generally connected by road. There are currently fourteen of the larger rail-connected plants designated as export plants, and these are equipped with sulphur forming facilities. The long distances between these plants and tidewater terminals in Vancouver is a very significant factor in complex logistics of Canadian offshore sulphur exports (Figure 6). Alberta and B.C. plants are located an average of 1,400 kilometers from tidewater.

Jan 1, 1986

By Peter Hall

The need for large volume covered storage has increased drastically in the last ten years. Increased world demand for such products as thermal coal, potash, metallic concentrates, etc., availability of land for large open storage and environmental issues have brought about this need. This paper discusses briefly demand, environment, types of covered storage and the Alternative Storage System "Eurosilo", a proven system for storage of dry bulk mateials in units up to 100,000 m3.

Jan 1, 1982

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By A. L. Miller, A. J. Chambers, P. R. Griffiths, D. A. Parks

"Diesel engines are one of the primary contributors to the presence of nano and ultrafine aerosols in ambient air and occupational environments. Exposure to diesel emissions has been shown to contribute to various adverse health outcomes of the pulmonary system and cardiovascular system. Currently diesel emissions in the workplace are monitored by way of collecting the aerosol onto filters, which are then sent to a lab for thermal-optical analysis using the NIOSH 5040 method, which measures elemental and organic carbon explicitly. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of diesel particulate matter (DPM) before the problem is identified. To remedy this, researchers from the National Institute for Occupational Safety and Health (NIOSH) are seeking to develop a field-portable method for measuring elemental and organic carbon in DPM aerosols. In the current study, we investigated the use of Fourier transform mid-infrared (FT-IR) spectrometry, which lends itself more readily to implementation in a real-time system than do the thermal-optical analysis methods. We have demonstrated a method for measuring organic and elemental carbon in DPM for a broad range of organic carbon (OC) to elemental carbon (EC) ratios (from 50.3 to 0.8). The ability to handle a wide range of OC to EC ratios is critical given the evolving diesel technology. INTRODUCTION Respiratory illnesses are common in mining industry workers [1] and exposures to toxic aerosols such as DPM can result in serious respiratory illness [2]. Health studies show a correlation between workplace exposure to diesel exhaust and an increased risk of lung cancer [3-8]. The International Agency for Research on Cancer (IARC) has characterized diesel exhaust as a human carcinogen [9], and similar classifications have been made by the World Health Organization and the California Air Resource Board. A recent study [10] suggests that the risk of lung cancer is approximately three times greater for heavily exposed workers. When compared to other aerosols in the mine environment, the settling time of DPM is significantly longer than that of dust due to their small particle size (typically < 1 µm) [11]. Additionally, submicron particles (such as DPM) are deposited in the lungs much more efficiently than their larger counterparts such as dust [12]. Previous studies focusing on particle morphology [13] show that the largest mass contributor to lung disease in mining is elemental carbon, which provides a solid core onto which hydrocarbons are adsorbed. In accord with those findings the Mine Safety and Health Administration (MSHA) decided on submicron total carbon as a surrogate for monitoring diesel particulate matter in the mining environment."

Jan 1, 2018

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By M. Springett

Organization of teams for rapid and effective evaluation of international mining properties requires special considerations beyond those needed for domestic activities. Experience, technical ability, a sense of perspective, humor and self-discipline are vital characteristics to look for in the selection of individuals for forming an efficient and productive team.

Jan 1, 1994

By Wallace W. Wilson

It scarcely 1s possible to read a new issue of any of the principal mining trade journals without noting some mention of a major new overseas mining venture with which one or more domestic companies are involved. These projects seem to follow a fairly consistant pattern; most are large open pit mines, with relatively low grade ore bodies but huge reserves; the total price tag will be in nine significant figures and around half or more of the total cost will be for infrastructure. West1 noted that nearly $7 billion is being invested annually for new mining projects and the expansion of existing mining ventures, in the free world. He anticipates that by the year 1975 such investments would reach the $10-11 billion annual figure, and that in the five year period 1972-76 total capital requirements can be expected to aggregate around $45 billion. The proportion of this total investment which will be financed in some manner is difficult to estimate because of the variety of available financing arrangements. West estimated that around 75% of the total capital would come from internally generated funds, with the balance from external sources. Conceivably a substantially higher percentage could be attributable to external financing, especially it the trend of recent mineral development in Canada and Australia is any criterion, and of course, including local sales of equity as a part of the package.

Jan 1, 1973

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization&apos;s structure that addresses the immediate and long-term impact of a company&apos;s products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By P. Grotjohann

In processing heavy mineral sands, the low feed concentration and respective high value of the desired minerals require high capacity production and sharp classification/separation techniques to reduce the specific production costs. The allflux® separator, a new process system introduced to the heavy mineral industry, meets these criteria in an economical way. Its two-stage process, a combination of rising current and fluidized bed technology, allows the treatment of extremely high massflows in a single unit. Using concepts that have proven successful in processing concrete sands for many years, testwork in coal, iron ore, and heavy minerals looks very promising.

Jan 1, 1998

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By M. J. Beus

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By A. D. S. Gillies

The provision of a suitable working environment in deep level mines requires the accurate prediction of the ventilation heat load. Mathematical models for predicting strata heat load have been under development since the 1930&apos;s and 1940&apos;s. Computer models for predicting this and other mine heat sources have been developed and refined over the last 20 years. Some empirical studies have occurred and there is an increased emphasis on the importance of underground studies. Any theoretically or empirically determined predictive method must of necessity make assumptions. Underground space with its irregular configurations and rough wall surfaces cannot be described by simple mathematical expressions. Some heat loads, such as machinery, may occur intermittently while others such as the influence of water evaporation are very difficult to quantify accurately. Current popular models for predicting mine heat load have been surveyed. In testing some of these it is often found that each estimates significantly different quantitative values for the expected load in a particular underground space under study. These differences are explained by the assumptions, simplifications and omissions implicit in each of these models. It would be easier to estimate conditions at any point if heat flow into mine air passageways could be described by simple equations with associated statistically-based confidence ranges. Use of probability distributions to indicate confidence ranges allows any heat level estimate to be expressed as a range of values with limits for maximum and minimum expected values. This approach allows many of the limitations of the popular predictive models to be overcome. A heat prediction method using this approach has been developed based on Monte Carlo simulation and tested on mine data from a number of operations. Heat flow levels which can be predicted by simple equations supported by probability distributions allow the engineer flexibility in adjusting a predictive model to the underground characteristics appropriate to the mine site under study. The influence of all heat sources present in the mine opening must be included. Prediction methods must be updated as mining systems and machinery change with time. Heat sources interact with one another and the system must therefore be understood in its entirety.

Jan 1, 1987

By John H. Smith

Because of increased pressure from Federal & State Regulatory Agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Pressure to minimize costs of waste treatment equipment and land usage makes development of a treatment process incorporating these desires mandatory. "Standard" methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, (such as iron, needing aeration) add to the problem of concentrating neutralized solids. In a paper published in the September 1970 issue of "Coal Age," *the results of extensive test work by personnel of the Homer Research Laboratories of Bethlehem Steel Corporation, Bethlehem Pa., were reported. This paper dealt specifically with development of a flow sheet to treat acid mine drainage (hereafter referred to as AMD) from coal mine operations. Regulations on discharged water required basic pH and low dissolved iron content after treatment. Liquid flows of over 9 MGD from

Jan 1, 1972

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By Stryker Magnuson

While probe drills are not strictly necessary for all projects, the incorporation and use of probe drills and pre-grouting adds capability and insurance to boring operations. Water ingress and unstable ground can be resolved before becoming a problem and resulting in costly delays through the use of enhanced, 360-degree probe drilling setups. To do this, proper design of the array of drill ports in the shield, matched to the possible ground conditions, is critical. For ground with exceptional water and instabilities expected, additional probing locations are low-cost additions that can lower risk and increase efficiency. In this paper we will look at recent and ongoing projects including the Lower Meramec Tunnel and Jefferson Barracks Phase 2. We will detail the design of those probe drill arrangements, and our overall recommendations for probing/grouting systems that best suit challenging ground conditions and keep projects running smoothly.

Jun 13, 2023