Search Documents

By S. Borner Schweizer

An overview over SAM’s approach to assess corporate sustainability performance illustrates how sustainability challenges are linked to trends, assessment criteria and finally company performance. This process is exemplified with some general and industry specific criteria. Lastly, results of the Dow Jones Sustainability Assessment 2004 show a considerable gap between leading and average companies. Best practice examples demonstrate how lagging companies could improve their sustainability performance.

Jan 1, 2005

By Donald M. Ulbrich

As all of us know, the "heat" is on for western coal. The need for western coal is critical if the nation is to reach the goals of Project Independence by 1985. Without the development of western coal, the goals will not be met. It's that simple! That's because 50 percent of our nation's coal reserves lie in the states of North Dakota, Montana, Wyoming, Colorado, New Mexico, Arizona and Utah. And surface mining is the key to unlocking these reserves. Of the nine states in the coal provinces, five-Wyoming, Montana, New Mexico, North Dakota and Arizona-are the best examples since surface mining accounts for 88 to 100 percent of the coal mined in each of these states. Collectively, their annual production more than doubled between 1969 and 1972, rising to 35 million tons per year. And, taken individually, each state's production has more than doubled, also. Total annual production from these five key states could very well exceed 180 million tons per year by 1980-four times the 1972 production level. The biggest producer among the five is Wyoming. Wyoming's production tripled since 1969 to nearly 14 million tons in 1973. So the heat is on for western coal, especially from Wyoming. Now we come to the question of how to mine this increasingly precious mineral. What are the available methods? First, let's take a brief look at several characteristics of western coal deposits.

Jan 1, 1975

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems.

By Jacques B. Wertz

However excellent the geologic map of an area is, it can only show what is exposed on the ground. It cannot and should not generalize the information nor complete the picture by inference: this is left to the examiner. Consequently, it becomes justified for him to use all expressions of geologic structure in order to gain an additional dimension in geologic interpretation, and particularly so in mineral exploration. In previous studies related to Arizona, the known faults were the starting points and a host of interpolated, supporting geologic factors described in earlier publications ascertained the presence of a series of structural trends and lineaments found to be rather continuous and persistent, even though unsubstantiated by geologic maps. In present studies pertaining to the humid environment, with the same aim of seeking major structural trends and lineaments, the starting points are morphologic expressions such as straight lakes and straight segments of rivers, among others, because there generally is not enough geology available. An example is given herewith for an area that straddles the International Border, north of Spokane. In both semi-arid and humid environments, one observes that mineral deposits quite often occur close to the intersection of a major fracture or lineament with some secondary trend.

Jan 1, 1971

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Qingming Feng, Jinhong Zhang

This study investigates the application of fly ash as a high-strength, water-resistant precast construction material through geopolymerization. The experimental results show that working conditions such as water content, sodium hydroxide (NaOH) concentration, curing temperature and curing time significantly affect the mechanical properties of the geopolymer matrix. Through optimization, compressive strength above 100 MPa was achieved, and the optimum working conditions were found to be NaOH concentration of 10 M, water content of approximately 14 to 15 percent, and curing at 90 °C in an oven for one day or at ambient condition for three weeks. Water-soaking tests show that the geopolymerization product has high water resistance without losing noticeable compressive strength even after one month of soaking time. The findings provide a novel method to apply fly ash as a high-strength, water-resistant precast construction material.

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By S. B. Bhagwat

The United States has abundant coal resources that could last at least another century. and probably longer at present consumption rates. Geographically, the coal resources are distributed over the entire nation including Alaska, although there are no coal deposits in the highly populated areas on the two coasts. This allows free access to the coal, but makes transportation more expensive. Not all coals can be utilized equally because they differ vastly in quality. The sulfur content of coals, considered as the most detrimental acid rain-causing element, varies from as low as 0.3 percent in some areas of the western U.S. to 5 percent or more in parts of the Midwest. The chlorine content, which causes corrosion of plant hardware, also varies regionally. The 1990 amendments of the Clean Air Act of 1963 (CAA) require that emissions of sulfur be restricted and rolled back in two stages by the year 2000. There have been a number of reports expressing concern about the future of the industry in the states where high sulfur coal is produced. The remedies devised by the federal government and many coal-producing states in the past to "se-cure" the future of the regional coal industries have focused on the physical task of removing sulfur rather than the economic challenge of doing so at a cost that will enable high-sulfur coals to survive and compete. The past remedies, generally, were not specific enough to account for the characteristics of regional coal deposits and did not look at the coal market as an integrated national and international entity. The State of Illinois has, in recent years, taken a more comprehensive approach to the solution of the problem.

Jan 1, 1992

By RICKARD HANSEN

Vehicle fires in underground mines pose a certain risk for which measures to prevent or mitigate the fires are highly important. Fire protection measures can be divided into active and passive measures, where active measures require an external power to work in the event of a fire, and passive measures could include an existing partition preventing fire spread. As passive fire protection does not rely on activation, it is expected to provide high reliability and a robust solution, and should be considered during the design process. This paper investigates passive fire protection measures that could be implemented in the design of mining vehicles. It was found that passive fire protection should include the use of several measures simultaneously to ensure fire protection throughout the different phases of a fire. Threshold distances for fuel components were calculated, and it was found that combining hydraulic hoses and electrical cables resulted in larger threshold distances. A pool fire along the underside of a vehicle will pose a certain risk, and passive measures should be focused on ignition prevention, making high demands on the insulation/shielding along the underside. Any occurring tire fire may pose a challenge, and the priority should be on preventing ignition. Potential measures include shielding the wheelhouse and applying fire-resistant sealings.

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.

By E. Allen Hendt

It is a pleasure to be invited to speak before a gathering of executives representing America's leading mineral companies, I welcome this opportunity, particularly because it comes at an important period in the development of U.S. commodity policy. This morning, I discussed our general commodity policy primarily in the. Context of the north-south dialogue between developed and developing countries. This afternoon, I would like to focus more specifically on potential cartel activity and U.S. mineral import dependence.

Jan 1, 1978

By Stephen L. Chryssoulis

The detection and quantification of invisible gold by microbeam techniques is discussed. Ion probe microanalysis is used to quantify the gold content of individual sulphide, sulpharsenide and oxide particles with a detection limit of 0.2 ppmw (g/t). The proton microprobe is used to determine the gold concentration of gangue minerals with a detection limit of 2 - 4 ppm. Using these techniques complete mineralogical balances for gold are obtained to assist in the process selection and optimization. A total of twenty gold and gold-bearing ores have been examined. Selected examples are presented.

Jan 1, 1990

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By Jr. Chilson

This paper addresses the slurry pump industry as it exists today by touching on the business aspects, and by discussing research and development for material metallurgy and hydrodynamics for wear improvement which reduce operating and maintenance cost for the customer. It demonstrates why OEM parts give better value for cost.

Jan 1, 1996

By Robert J. Russell

The importance of grinding as a unit operation in all industry has caused much effort to be expended toward improving the facility with which grinding can be done. Endeavor has continued nearly 100 years to formulate laws governing crushing and grinding. This has not been without controversy. However, grinding is an experimental science and our useful knowledge originates in experience. The recorded experience is grinding history. Today, many types of size reduction equipment, each with variations, are available to industry. Frequently, more than one type of grinding equipment will meet a requirement of grinding. However, an economic evaluation of installation and operating costs generally indicates a preferred type. The selection of grinding equipment requires' a consideration of the purpose in grinding, the characteristics of the material to be ground, equipment available for grinding, and the manner in which it can be applied best.

Jan 1, 1960

By Terry W. Engelhart

"A computer-based approach to online supervisory control and operations management of bulk materials handling terminals". This paper describes an integrated computer facility supporting the functions and responsibilities of shift operations, scheduling, maintenance and management using real-time interactive techniques. The functions and responsibilities as related to coal export terminals are specifically addressed, although these functions would be equally applicable to other terminal configurations and other commodities. A discussion of the resulting benefits are presented: - throughput efficiency - long-term planning and scheduling, using simulation - operations monitoring and protection - demurrage/despatch optimization - preventative maintenance - operational productivity

Jan 1, 1982

By Simon D. Strauss

The recession that began in late 1980 has proved to be not only prolonged and severe, but in certain ways unique in its effect on the mineral industries among the periods of economic slowdown experienced in the Western world since the end of World War II. This time almost all minerals have been affected. In previous business turndowns, by contrast, some mineral sectors have with-stood economic adversity well. They experienced little or no adverse effect-thanks either to a strong secular expansion in the markets for their particular product or to specific factors that caused demand to be well maintained. For example, aluminum, molybdenum, and nickel are three metals that enjoyed extraordinary growth in applications during the years 1946-1973. These metals were little affected during the recessions that occurred in that era. Similarly, coal did not suffer a pronounced drop in sales in the 1974-75 turndown because, with the price of oil rising sharply, a switch away from oil and back to coal was clearly indicated for some energy-intensive applications. Oil itself was largely impervious to the ups and downs of the business cycle until very recently. And the precious metals, gold and silver, have often been regarded as benefiting from reduced economic activity because labor becomes more available, productivity rises, and operating costs diminish. In the current recession, however, no major mineral has escaped the broad trend. The secular growth factors that were previously so evident for aluminum, molybdenum, and nickel have disappeared, at least temporarily. The stable pricing behavior that previously characterized all three of these commodities has been replaced by extreme price weakness and apparent inability of the major producers to continue their roles as market leaders. Coal and oil both have suffered from a sharp drop in energy requirements. There are those who now anticipate a collapse of the market control over oil prices so clearly exercised by OPEC since 1973. If oil prices are no longer effectively controlled by the governments of the exporting countries, then coal prices are also certain to be affected. And the combination of high interest rates, tight money, and a change in public perceptions of precious metals put the skid under gold and silver quotations in 1981 and early 1982. Although inflation has been viewed as the scourge of most Western countries ever since the oil crises of 1973-74, prices-in constant dollars-of most minerals have not risen. On the contrary, with the exception of the precious metals and oil, for most minerals the prices that prevailed at the end of 1982 were close to the levels of the Great Depression of the 1930s in constant dollar terms. Table 1 compares prices for copper, lead, zinc, and aluminum at the end of 1982 with the average prices in 1934, stated in constant 1967 dollars. This emphasis on prices for mineral commodities reflects the fact that profits of mining enterprises vary directly with the level of prices. Manufacturing and retailing enterprises march to a different tune. They establish sales prices based on costs. Their profits tend to vary with volume. Commodities are for all practical purposes fungible, that is the advantages of known brands in marketing manufactured goods have little application in a commodity market. Thus the individual seller of minerals is unable to establish his sales prices. Except where a monopoly is present, he must sell at the going market. His option is to abstain from selling if he finds the price unremunerative. In past recessions, some mineral producers chose to do precisely that-either accumulating a substantial share of their output in inventory or, in prolonged downturns, abstaining from production. During the current recession, however, private-sector mining companies did not have the option of accumulating inventories to any great extent. Capital costs for new mineral projects or for expansion of existing facilities have escalated at an alarming rate since the early 1970s. Added to this has been the heavy cost of installing pollution control or safety equipment to comply with the regulations adopted in most industrialized countries (and particularly the United States) since 1968. The consequence has been that the financial position of most major mineral enterprises in mid-1980 was already strained. To finance increased inventories meant incurring additional funded debt at high interest costs, thus impairing the concern's credit rating. Management Choices Private-sector managements have had to face up to the alternative of either continuing to produce at an unchanged rate and marketing output at unremunerative prices or reducing output. The latter has meant either operating at a curtailed rate, with con-

Jan 3, 1983

By Emily Sarver

"Across all sectors and commodities, a common theme is driving progress in raw resource supply: sustainable development (SD). Over the past few decades, the mining and minerals industries for their part have undertaken significant and intentional changes at every level to become more responsible — no longer to just their shareholders, but also to the environment, to the communities in which they operate and to society at-large. Led by some of the global majors, these industries have indeed helped to define and operationalize the basic principles of sustainable development. Now in the midst of a full-on cultural shift, they are also key players in the continual effort to re-examine and calibrate practices to meet dynamic and increasingly complex objectives.SME’s technical position statementAs a home for so many technical experts and practitioners, SME has long recognized the importance of a commitment to sustainable development by the mining and minerals industries. In April 2016, the Society formally adopted a technical position on the topic following years of participation in, and support for, related activities. The full position statement appears below. It was drafted, revised and presented for approval to the board of directors by SME’s Sustainable Development Committee.Statement of Technical Position on The Mining Industry and Sustainable Development:• The National Environmental Policy Act of 1969 (NEPA) and the Surface Mining Control and Reclamation Act of 1977 (SMCRA) imposed considerable environmental restrictions on the mining industry; SME has always reinforced strict adherence to the laws.• In 2002, SME established a Sustainable Development Committee to lead its efforts in this area and to propel the organization into global prominence.• SME is a signatory to the Milos Statement of 2003 on Sustainable Development, so it is committed to providing scientific, technical, educational, and research skills in minerals, metals and fuels.• SME recognizes that SD programs adopted by the industry have a tangible return on investment through brand recognition and loyalty, facilitation of permitting, reduced occurrence of community protests and vandalism and diminished political risks.• SME actively promotes educational programs that encourage professional growth and interaction with the engineering professional community through books, articles, symposia, short courses and/or conferences on sustainable development in the mining and minerals industries.• SME has developed abundant expertise to provide balanced advice to government bodies, congressional staff and other interested organizations."

Jan 12, 2017

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016