Search Documents

By W. M. Tuddenham

It would be most difficult to place a date on the beginning of the revolution in analytical techniques that we have witnessed in recent years; but there is no question that the period since the end of World War II has seen a major change in thinking with respect to control and accounting analyses. For reasons relating to competition, much of this change was brought about in the chemical industries and only more recently has begun to affect directly the mineral industries. In considering the subject outlined in the title of this paper, one might well be tempted to discuss solely the more exotic methods of control and automation which have come into being in the past short while. In this paper, however, an attempt will be made to take a broader view and consider not only the application of newer purely physical methods of control but also those phases of chemical plus physical analyses that have bearing on our industry.

Jan 1, 1962

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By Prashanta K. Chatterjee

The planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc, do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered. Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate many layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment.

Jan 1, 1986

By Paul C. Lingo

The title of my talk today might lead you to two logical conclusions: The industry is faced with a problem that requires a solution and after discussing the problem I will offer a solution. The first conclusion is painfully accurate. One need only look at the accident statistics to be aware of the problem. During the eight-year period 1954 through 1962, the United States Bureau of Mines reports that falls of rock and coal accounted for 1,435 of the 2,516 fatal injuries that occurred in underground bituminous coal mines. Some improvement was made during 1962. For the first time since records have been kept, falls of rock and coal accounted for less than 50 per cent of the underground fatal injuries. The 105 deaths recorded in 1962 indicate that a great amount of work remains to be done in this area. As to the second conclusion, let me assure you at the outset that I have no panacean solution; however, I do propose to discuss some aspects of the problem and some possible methods of solution. What methods of solution are now, or have been employed in attempting to solve the problem? More specifically, what methods have you and your associates used? Has it been an orderly well thought out approach to the entire problem, or has it been a somewhat piecemeal approach which tackled the immediate problem and left the total problem for another day? Perhaps a new approach may be in order.

Jan 1, 1964

By Raymond A. Bradbury

A significant news item appearing in a coal mining journal in November 1969 stated simply that a Caterpillar D-333-CNA engine had received Bureau of Mines Schedule 31 approval. This item occurring at the time a new mining property in Martin County of East Kentucky was being prospected and prepared for mining, resulted in the manage-ment of Martin County Coal Corporation asking the question, "Why not use diesel equipment in our new operation?" Martin County Coal Corporation is part of the A. T. Massey Coal Company, Incorporated organization. The property being developed is on a 17,500 acre leasehold obtained from Pocahontas Land Corporation and lies in the Wolf Creek area of Martin County. The Norfolk and Western Railway Company built a 24-mile railroad into this undeveloped section of Kentucky to tap a huge reserve of steam coal. Duke Power Company is the customer who will take all of the production from Martin County Coal Corporation mines which ultimately is projected to be 2,000,000 tons annually. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton are being deep mined now and it is in those mines that the diesel haulage equipment was introduced. This paper will endeavor to trace the steps loading to the introduction of the first diesel-powered Wagner Mining Equipment Company ScoopTram in a coal mine in America. It will further elaborate on the features which make this unit a very versatile and useful utility unit as well as the safety features which are incorporated in the machine. The success of this first unit led to the placing of

Jan 1, 1972

By S. Angioletti

This paper addresses strategic investment decisions when they are nested in a project development format where each project is implemented in phases and each phase is approved to move on to the next phase only if certain technical and economic requirements are met. This configuration is sometimes referred to as a ?Project Portfolio?. Mining companies maintain project portfolios in their exploration investment plan. This study proposes a procedure to best manage an exploration project portfolio including technical and economic uncertainties. The procedure may support decision makers in a simple and intuitive way, while maintaining the rigor and precision required by the rather large amount of financial resources typically called for by mining projects. The procedure was tested in a real case study of a gold mining company and its exploration projects portfolio. The procedure uses the following approaches: i) investment valuation methods under technical and market uncertainties based on Option Pricing Model, Real Option Theory and Option Space; ii) portfolio management and Stage Gate®1 method; iii) Monte Carlo simulation.

Jan 1, 2010

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By Jessica M. Wempen

"Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has application for monitoring subsidence with high resolution over short periods. DInSAR uses radar images to measure centimeter-level surface displacements. In the images, ground resolution can be relatively high, with each data point (pixel) representing the average displacement over an area of several square meters. The image data are acquired regularly which allows subsidence to be monitored sequentially over short periods; imaging periods typically range from weeks to months.Monitoring subsidence over short periods with high spatial resolution has potential to provide insight into the dynamics of subsidence and into relationships between mine advance and subsidence. In this study, for three longwall mines in the western United States, initial subsidence occurring at the start of longwall advance is quantified over short periods (12 to 72 days). C-band interferometric wide swath Synthetic Aperture Radar (SAR) images from the Sentinel satellites are used to quantify the subsidence. Overall, the data show initial development of subsidence, expansion of the subsidence trough, and the advance of subsidence in the direction of mining.INTRODUCTIONApplied Differential Interferometric Synthetic Aperture Radar (DInSAR)Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique that can be used to quantify small displacements of the Earth’s surface. Using data from the Seasat satellite, which was launched in 1978 (Jet Propulsion Laboratory, 2018), studies by Goldstein, Zebker, and Werner (1988) and by Gabriel, Goldstein, and Zebker (1989) applied Synthetic Aperture Radar (SAR) interferometry to topographic mapping and displacement monitoring. These studies established the potential for broader applications of radar interferometry. Studies by Foxall, Sweeney, and Walter (1998), Wright and Stow (1999), and Carnec and Delacourt (2000) represent some of the earliest evaluations of DInSAR for mine subsidence monitoring. All three of the studies demonstrated the application of DInSAR for quantifying mine subsidence. They also demonstrated difficulty accurately measuring subsidence over long periods due to data decorrelation. DInSAR continues to be evaluated as a tool to quantify surface deformation related to active and historic mining. For example, see Vervoort and Declercq (2018), Wempen and McCarter (2017a), Chen et al. (2013), and Liu et al. (2013). Technologies associated with SAR interferometry continue to develop. Recently launched satellites have relatively high spatial and temporal resolutions, and data processing methods and data accessibility are improving."

Jan 1, 2019

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda's mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda's program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000

By Tench C. Page

The Yarnell gold deposit is located 1.5 km (1 mile) south of Yarnell in the Weaver mining district of Yavapai County, AZ (Fig. 1). Elevations within the area of the deposit range from 1400 to 1560 m (4590 to 5120 ft). Historic production, principally from quartz veins localized along the Yarnell fault, was about 200 kt (220,000 st) at an average grade of 6.9 to 10.3 g/t (0.2 to 0.3 oz/st) gold. The federal government closed the mine in 1942 due to World War II. Norgold Resources Inc. leased the property in 1988 and joint ventured it with Asarco the same year. Asarco drilled 7822 m (25,660 ft) in 96 reverse circulation and four diamond drill holes and identified 8 t (260,000 oz) gold reserve. IBema Gold Inc. acquired Norgold in 1991 and is currently permitting the project. Production is expected to begin within the next two years

Jan 1, 1994

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By Yi Zheng

Under normal circumstances, methane released along a longwall face represents only 10%-20% of the total me- thane emitted from the entire longwall panel. However, there might be a sudden surge of methane at the face which may cause a potential problem because the friction from shearer cutting, support movement, and scraper conveyor dragging can be ready ignition sources. Therefore, to predict the distribution of methane will be critical to prevent possible explosions. In this paper, methane dispersion patterns along a lognwall face are simulated under normal and abnormal conditions. With the simulation of methane released from the face, around shearer drum, and from the broken coal on the conveyor, places with possible high methane content can be identified by different phases of working process and shearer positions. Local ventilation measures are evaluated so precautionary measures can be planned ahead.

Jan 1, 2012

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By Thomas J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank-run gravels averages about 0.1 grams per ton (about $1.45 per ton), based upon $14.47/g (345O/ounce) gold. Tine Reichert cone, in conjunction with a conventional shaking table, re- covers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1% is -i4 microns (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1981

By H. Huang, R. N. Gow

"In Part I, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. The diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals – tennantite, sinnerite and lautite – and compared with enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. IntroductionA comprehensive thermodynamic review has been conducted on the aqueous copper-arsenic-sulfur (Cu- As-S) system (Gow et al., 2014, 2015a, 2016b; Gow, Huang and Young, 2016c). Data on the free energies of more than 100 species were collected from various authors, and thermodynamic databases collated to produce mass-balanced EH-pH diagrams using the thermodynamic equilibrium calculation software STABCAL (Huang, 2014). The full database is listed and discussed in Gow et al. (2015a). Diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2015a), acid conditions (Gow et al., 2014) and alkaline sulfide leaching conditions (Gow et al., 2015b).In the present study, additional mass-balanced EH-pH diagrams were generated by changing the Cu-As-S stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species were shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions and sulfur oxidation states."

Jan 1, 2016

By Ronald E. Heuer

The significance of surface settlement over soft ground tunnels is well recognized. Cracked buildings, streets transformed into lakes, broken utility lines, to underpin or not to underpin--all are familiar problems. The basic causes of surface settlement are recognized. Possibly the most common and troublesome cause is "lost ground" during construction. Lost ground refers to removal of a larger volume of ground (Ve) than is eventually occupied by the final tunnel structure (Vt). A number of sources of lost ground in shield tunneling have been identified, as illustrated in Fig. 1. These include 1) face loss, 2) overcutting loss, 3) annular tail void loss, and 4) loss through the lining. The ground generally does not stand unsupported around the completed tunnel lining as illustrated in Fig. 1, but moves in to fill the lost volume, resulting in subsidence of the overlying ground surface as shown. As suggested in Fig. 1, lost ground and surface settlement associated with overcutting and the annular tail void tend to occur systematically along the tunnel length. This "systematic" lost volume is "limited" in the sense that it is restricted to an upper limit determined by the shield and lining geometry. Partially controlled face loss may sometimes contribute to this systematic loss. This lost volume is commonly a few percent of the nominal tunnel volume. The resulting surface settlement over the tunnel is commonly in the range of a few inches or less and develops over a period of hours to days. Although they may have a significant impact on surface facilities, systematic ground loss and settlement frequently have little adverse effect on tunneling progress.

Jan 1, 1976

By Ron F. Schritt

Over the many years since the development of the steam powered shovel, various powering and control techniques have been employed for the various shovel functions. While volumes have been published on this subject, this paper will be limited to a very brief discus-sion of one of the latest of these and its application to a unique machine. The evaluation of the subject machine is far beyond the scope of this discussion, which will be limited to the techniques and equipment employed, and the considerations involved in their choice. The basic requirements for any power and associated control system for any power shovel function have remained relatively un-changed over the years. To the extent possible, such an equipment grouping must be: Easy to install during fabrication Easy to maintain and repair by available personnel Life cycle cost competitive Adequately reliable Adequately responsive And as may be expected these factors are arranged in various orders of priority by different manufacturers and users. All the various time honored approaches have to some extent fulfilled these require-ments but were discarded or fell into disuse when more effective approaches were developed. The latest in this long line of develop-ments and perhaps the most promising is that of electro-hydraulic controls and hydraulic drive.

Jan 1, 1977

By R. E. Anderson

Canada encompasses an area of approximately 9,976,000 kilometres. It is comparable in size to the United States, but because of climatic conditions and limited transportation facilities, much of the area is unsuitable for agricultural or industrial development. We have a population of 22,000,000 - most of whom reside within a hundred mile belt paralleling the Canadian-U.S. border. Our principal cities in order of size are Montreal, Toronto, Vancouver, and Winnipeg. We have a total of 10 provinces, each of which elects its own - government. The Yukon Territory and Northwest Territories covering the northern half of the country, are administered by federal government agencies. The mining industry employs approximately 9% of the labour force and accounts for more than 40% of all tonnage shipped on Canadian railroads and inland waterways. In 1974 it produced $4,800 million in mineral wealth. Canada ranks first in world production of asbestos, nickel, zinc, and silver and has significant production of copper, iron, molybdenum, lead and other mineral commodities. During the past decade Canada, like many other western countries, has undergone dramatic economic and social change. This trend is continuing, and its effect on the Canadian mining industry has produced conflicting results. From the industry's point of view, some of the more negative aspects include a steadily increasing involvement by government at municipal, provincial and federal levels through the imposition of Stricter controls, regulations and taxation policies, a rising tide of nationalism, which advocates public ownership of all natural resources, the spectre of inflation (currently increasing at the rate of 8% per year) and unsettled labour conditions.

Jan 1, 1976