Search Documents

By J. D. Lowell

The gold content of prophyry copper deposits ranges from less than .05 gmt (ppm) to more than 1.0 got, and most deposits contain on the order of 0.05 gmt Au. Perhaps the highest grade mineralization which has been found in close proximity to a porphyry copper is the Ok Tedi Gold Cap orebody whose grade falls in the 2-3 gmt Au range.

Jan 1, 1988

By Chen Bing Ching

Hsikwangshan mine is located at Lengshuijiang city of Hunan Province. It is a stibnite deposit. The orebody is gently inclined; its ore run is about 3 km in length and extends about 1.2 km along the direction of dip. The thickness of the ore body is non-uniform and varies from 1.5 to 20 m. The orebody is mined by room and pillar and cementation filling. The nine levels at the ore top have been mined out. At present, the mining operations are at the eleventh level. The mine ventilation system consist of three main fans which are installed in different shafts and are ventilated in parallel. The main fans can be connected to each other through comprehensive return air drifts. Two of the fans are located underground and the other on the surface. The general configuration of the ventilation system is shown in Figure 1. Because the operating areas are scattered and vary frequently as well, it is difficult to bring about air flow control. If the air flow cannot be varied with the variation of production in time, the air quantities are not sufficient in some areas and are excessive in others. However, it is also a problem to coordinate the three main fans with one another to obtain the optimum economic cost of operation. In order to make the air delivery fit the variation of production continuously to satisfy the ventilation requirement of the working faces and to reduce power consumption, we have made a great effort over five years to install an automatic control system for mine ventilation at the Hsikawangshan mine. The key part of this system is a microcomputer. The whole system consists of a console, which is located at the surface; the circuit network that is provided for signal transmission; air doors and ventilators at the working face; the scale air doors which are installed at the main branch airways; main fans and their speed regulating devices, as well as the sensors used for observing pressure, air quantities, temperature and the concentration of carbon monoxide, etc. This system can continuously telemeter the air quantities and carbon monoxide concentration in the main branch airways, air pressure, air quantities, electric current, the temperature of the bearings of the main fans, etc. According to the production air requirements, the system controls the ventilators or air doors which are located at the working faces and regulates the air quantity in the main branch airways. It can also choose the optimum mode of operation automatically, and regulate the rotating speed of the main fans to guarantee the least total power consumption while satisfying the total air quantity requirements. If abnormality of the observed results is discovered, the audible and flashing light alarm signal starts up automatically. The operating mode of ventilation equipment also feeds back to the control room and displays on the console. The configuration of control the system is shown in Figure 2.

Jan 1, 1987

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: 1) as a diverse group of fine-grained minerals, 2) as a rock term, and 3) as a particle size term. As a rock term, clay is difficult to define because of the wide variety of materials that comprise it; therefore, the definition must be general. Clay is a natural, earthy, fine grained material comprised largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates comprised mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic, e.g., halloysite and flint clay. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 pm. as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 pm. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1988, 1989, and 1990 productions according to the US Bureau of Mines (Ampian, 1992). As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this section these commodities are organized as follows: 1) bentonite, 2) common clay, 3) hormites, and 4) kaolin. Fuller's earth is discussed in both the bentonite and hormite chapters. Fuller's earth is a term based on use, and both bentonites and hormites are sold as fuller's earth. The overlapping is particularly evident where both bentonite and non-bentonite fuller's earth are used for the same purposes or products, such as in drilling mud, bleaching or clarifying fats and oils, and carriers for insecticides and fertilizers. Kaolin, ball clay, halloysite, and refractory clays are grouped together because they consist mainly of minerals of the kaolin group. Common clay is a grouping of several fine-grained materials, including shale, sometimes referred to as miscellaneous clay. The scientific and technological publications pertaining to clays

Jan 1, 1994

By Ronald J. Doll

The selection and matching of the conveyor drive components (Figure 1) determine the initial cost, long term costs, and how well the drive performance is matched to a project's long term production goals. This paper will cover the specification criteria and considerations that should be included in a conveyor drive specification. It will also review the practical aspects of the specification's intent and the solicitation of alternatives.

Jan 1, 1998

By James M. Prudden, E. P. Jucevic

The Divide mining district occupies the center of a Tertiary caldera hosting the famous Divide silver lode and the crosscutting Gold Mountain mines. The northwest-southeast trending silver lode hosted ore with typically a 100:1 silver:gold ratio, high molybdenum content and argillic alteration dated at 16.5 m.y. within the Fraction Tuff. The east-west trending Oddie Rhyolite flow dome at Gold Mountain experienced possibly several periods of resurgence with repetitive silicification, brecciation and attendant precious metal deposition forming stockwork type mineralization. Silver-gold ratios average 10:1 for the mineralization phase of this 16.4 m.y. intrusive event. Similar chalcedonic mineralization registering a 3:1 silver:gold ratio cements conformable breccias within the Oddie Rhyolite basal flows unconformably overlying the Siebert Tuff on the northern flanks of Gold Mountain. Gray and red chalcedonic breccia matrix in the King Tonopah member of the Fraction Tuff contains a 50:1 silver :gold ratio.

Jan 1, 1990

By R. C. Timberlake

In the past three years there has been a great amount of attention given to phosphates world wide, and in particular to the Florida Phosphate Industry. I would like to relate some of the most recent history of the industry and give you a personal outlook for the future. Phosphate rock has been produced in Florida since its discovery on the Peace River in the 1880's. Through 1976, approximately 720 million ST of rock had been mined from Florida reserves, and it is my opinion that there are at least 1.2 billion tons remaining which are consolidated, accessible and can reasonably be expected to be permitted for mining. Over half the 1.2 billion tons will be deeper, more scattered, leaner and will produce lower grade rock than the Bone Valley of Central Florida has tradition-ally produced. In 1973, '74, '75 and '76 the Florida Phosphate Industry produced 32.6, 34.0, 38.2 and (38.0) (P) million ST of phosphate rock respectively. This rock was produced by ten mining companies, Agrico, Borden, Brewster Phosphates, Gardinier, Grace, IMC, Mobil, Occidental, Swift, and USS Agri-Chem; mines are located -17 in Polk County, one in Hillsborough County and two in Hamilton County, Florida. Phosphate rock is used by local companies in Florida primarily to produce phosphoric acid from which DAP and TSP is manufactured. Florida acid producers use about 15 million STPY in acid plants in Florida, and another 7.5 million STPY is consumed by acid producers in plants on and near the Mississippi River. Somewhat

Jan 1, 1977

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By Bryan Morris

Quebrada Blanca (QB) is a copper project located in the semi-arid Andean highlands of northern Chile. The operation is situated 170 km ( 105 miles) southeast of the port of Iquique and 30 km (18 miles) west of the border with Bolivia, at an altitude of about 4300 m (14,000 ft) (Fig. 1). The QB ore body is a secondarily enriched porphyry copper deposit containing reserves of 85 Mt (93 million st) grading 1.3% copper. Underlying the enriched zone is a significant primary ore zone containing several hundred million tons grading about 0.5% copper. In the late 1970s and early 1980s Falconbridge and its affiliates spent $20- $30 million exploring the deposit and conducting feasibility studies. Falconbridge, however, decided not to develop the property. It was returned to its owners, Empresa National de Mineria (ENAMI), a Chilean state mining corporation. In 1988, ENAMI announced its intention to privatize the property through public bidding. Cominco Resources, then 61% owned by Cominco Ltd., examined the property and the extensive data base developed by Falconbridge. In conjunction with its parent company, Cominco Resources submitted a proposal to ENAMI to construct an open- pit mine, with heap leaching and solvent extraction/electrowinning (SX-EW) processing facilities. The plan would use patented heap leaching technology developed by Sociedad MineraPudahuel (SMP), a privately owned Chilean mining company. At that time, a $150-million project that would produce about 45 kt/a (50,000 stpy) of cathode copper was envisaged.

Jan 1, 1993

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By M. Kawulak

The necessity to protect the environment can limit mining activities and make some areas less attractive for the prospecting and exploration of mineral deposits. In Poland, the main environmental factors that restrain Irumng are: 1. Regional A Protection of the landscape B. Protection of ground water from contamination and depletion 2. Local A Conservation of fertile soils B. Conservation of forest resources C. Preservation of natural, cultural, and historical monuments The regional factors listed above that can limit mining are presented on a map of Poland. These data, combined with maps of known and potential mineral deposits, make it possible to delineate general levels of limitation for various mining-related activities varying from "no existing environmental limitations" to "no allowed industrial activity" As an example, a compilation of such data is presented for lignite exploration and mining in Poland. Lignite deposits occur within Upper Paleocene to Upper Miocene clastic strata at depths ranging from a few to 300 m. The thickness of the lignite is generally a few meters, but can locally reach over 100 m within grabens. As a result, the overburden-to-lignite thickness ratio varies from less than 1 to over 20. Within the same Tertiary strata, and within overlying Quaternary strata, several aquifers exist that produce good quality water that may be contaminated or depleted during lignite mining. The protection of these ground waters is the main factor limiting lignite mining and should be addressed in mining and environmental policy and planning.

Jan 1, 1996

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By Philip U. Santacroce, James H. Meinholz

INTRODUCTION The Milwaukee Metropolitan Sewerage District (MMSD), is a special purpose sub-regional agency that provides collection and treatment services for sanitary wastewater for an area of 420 square miles (1088 km2) in 27 municipalities in the Milwaukee, Wisconsin metropolitan area. During its almost 75 years of existence, it has constructed 464 km of intercepting sewers, the majority in tunnel, and two sub-regional secondary wastewater treatment plants. The present program, the $1.7 billion Milwaukee Water Pollution Abatement Program, was started in 1977 and developed from ongoing internal planning, the Federal Clean Water Act and court judgments. Elements of the Program include improvement and expansion of the two treatment plants; rehabilitation of older in-place sewers; building new interceptors and relief sewers and providing capacity for high volume storage in approximately 32 km of deep, large diameter rock tunnels; reducing combined sewer overflow; and disposal/utilization of the solids that remain after the treatment process. The construction phase of the Program accounts for $1,105,900,000 within 335 separate construction contracts, 211 let to date, and covers a span of 15 years, starting in 1979 and running through 1994. Conveyance System construction cost is estimated to be $650,000,000 or about 60 percent of the total. Through December 1986, in terms of dollars, the total construction program is about 38 percent complete with Conveyance at 34 percent complete.

Jan 1, 1987

By Richard M. Levine

Now that the former Soviet Union has divided into 15 countries, it is necessary to analyze separately the industrial mineral position of each of these countries. Industrial mineral data The former USSR was one of the world's largest producers of industrial minerals and had some of the world's largest reserves. Production and reserve figures, however, must be qualified. Even when these figures were reported by the Soviets, it was not clear that the production figures were for products that would be equally marketable in a competitive market economy. The reserve figures are based on the Soviet system of reserve classification, which is not directly equatable with the US Geological Survey and US Bureau of Mines classifications of economic reserves in market economy countries. The Soviets reserve classification system, in terms of which reserve figures will be given, is based on the reliability of the quantity of the material in place. The Soviet system assigns each occurrence to one of seven categories A, B, C1 and C2 are considered reserves; P1, P2, and P3 are considered resources. Mining in the former Soviet Union was authorized on the basis of the reserves in place in categories A, B and C, which had to be in prescribed ratios. However, the categories A, B and C do not necessarily correspond to Western concepts of material economically exploitable under present market prices with existing technologies.

Jan 1, 1992

By Kenneth K. Humphreys

27.1-HISTORY, PROCESSING STATISTICS KENNETH K. HUMPHREYS 27.1.1-MINERAL PROCESSING HISTORY The processing of minerals predates recorded history. Many processing techniques have existed for thousands of years. For example, Georgius Agricola, in De Re Metallica (1556), described equipment and techniques, such as picking tables, smelting furnaces and cupolas of various types, sieves, launders. various types of crushers and grinders and other equipment, all still in use in one form or another. In translating Agricola's work into English, the late Herbert C. and Lou Hoover provided the following summary indicating the early history of particular mineral- processing operations :

Jan 1, 1973

By A. Arik

1his paper presents a modified ordinary kriging technique referred to as the "Nearest Neighbor Kriging" (NNK). The method is a simple and practical tool to use when the ordinary kriging (OK) results are unreasonably smooth, especially when estimating recoverable ore reserves for deposits with skewed grade distributions. NNK is robust and globally unbiased like OK. However, it is more advantageous over OK because it can control some of the smoothing and conditional bias which have been the major pitfalls of OK in many grade estimation cases. The paper details the methodology of NNK and its application to a gold deposit.

Jan 1, 1998

By Steve Crewdson

High tonnage hoisting of materials by vertical conveyors through deep shafts is a relatively new concept in mining that is proving to be effective. The development of the Pocketlift® belt by Metso Flexowell, located in Moers, Germany, enabled the installation of a deep shaft vertical conveyor in 2002. This application followed years of design and operational experience gained in medium-depth shafts around the world. The design, manufacture, installation and operational experience of an 1,818 tonnes capacity, 273 meters vertical lift, Pocketlift® belt system at the White County Coal Pattiki 2 Mine is the subject of this work

Jan 1, 2004

By Andrew J. Regis

Resource figures for bentonite clays are generally based on stratigraphic, sedimentary geologic data and drilling and sampling. Estimates of bentonite resources and/or reserves commonly found in the literature report on bentonite occurrences in specific localities or areas but none on any documented comprehensive estimates of bentonite resources. From 1974 thru 1977 the Bureau of Land Management conducted extensive studies of the resources of commercial grade bentonite in the three state region. These investigations consisted of: 1. Stratigraphic and geologic sampling with supplemental drilling data, followed by geostatistical analysis. 2. Data compiled from a systematic search of county and state records on mining locations, leases and acreage filed for bentonite. Estimates of resources of commercial grade bentonite using industry parameters were calculated from these data sources. It is concluded that there exists from 1.5 to 2.4 billion tons of in-place bentonite in Wyoming, Montana and South Dakota. Assuming a 5 percent annual growth rate for the industry, this would indicate a life of 62 to 73 years.

Jan 1, 1979

By L. S. Harris

The application of briquetting in various chemical, mineral, mining and metallurgical processes has been rapidly increasing in the past two decades. This is, in part, due to the development of new, more economical and higher performance briquetting equipment. Some of these developments, which have reduced the operating and maintenance costs,, include anti-friction bearings, hydraulically applied pressure enclosed and sealed gearing and bearings, tapered predensification feed screws, water cooling and materials of construction capable of operating at temperatures up to 18000F, and control systems capable of maintaining optimum briquette quality control. The briquets can be formed into almost any desired size and shape, To date, with present rotary briquetting presses in the 25 to 500 ton force range, briquets from 1/4" to 6" length are presently being used, some of which are illustrated in Figure No. 1. In force fed rotary briquet machines, these shapes are produced by feeding the material in between a pair of counter rotating rolls, as illustrated in Figure No. 2. The rolls have forming dies indented into their circumferential surface, as illustrated in Figure No. 3.

Jan 1, 1973

By Kenneth R. Dickson, I. Michael Gowring, Gary M. Davey

The Kemano Power Tunnel is currently being constructed by a joint venture of Atkinson, Kiewit, and Commonwealth. The 5.73 m diameter, 16.1 km long tunnel is part of the Kemano Completion Project in British Columbia, Canada which is being developed by Alcan Smelters and Chemicals Limited. The discussion includes the refurbishment and development of Robbins TBM 189-229 previously used at Calaveras (RETC Proceedings, 1987), the logistics of conducting a tunneling operation in a remote area with adverse weather conditions, in addition to a description of the work and the performance details in the various geological conditions encountered to date.

Jan 1, 1991

By William E. Cutcliffe, John A. Ames, John D. MacFadyen

Webster's dictionary nearly equates portland cement with its current primary definition of cement. Although such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to varieties of portland cement including portland-pozzolan cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far comers of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry since 1756 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic, mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or burning) step, which brings about the necessary changes in the raw materials. This pyroprocessing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The US Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relates to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. In analyzing cement industry production rates, it is well to keep in mind that measurement of raw materials requires the reader to recognize that approximately 1.6 t of dry raw materials are required to make 1 t of clinker. This number can vary depending on the amount of kiln dust wasted. Also that to produce 1 t of portland cement required .94 to .96 t of clinker, the remainder being gypsum or anhydrite. A ton of masonry cement or pozzolanic cement re- quires considerably less clinker.

Jan 1, 1994