Search Documents

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"During the last ten years great strides have been made, on the Mesabi Range, in the practice of beneficiating low grade iron ore material. By .beneficiation is meant all methods of removing impurities, and raising the iron content to a point where it can be sold in open market, the principal impurities being silica and moisture. The • general processes to which low grade iron ores are amenable are as follows:1. Thermal(a) Drying ; removes hydroscopic or atmospheric moisture. .(b) Calcining; removes carbon dioxide from iron carbonate, molecular water from hydrated hematites, and atmospheric moisture.Roasting; removes sulphur, carbon dioxide, molecular water and atmospheric moisture.Agglomeration; primarily for the purpose of preparing finely divided material for blast furnace; briquetting and sintering.2. MechanicalScreen sizing; removes rock and sand.Classification; removes sand by means of currents of water of varying velocities.Log washing; removes fine sand.Jigging; removes larger particles of impurities than is possible by log washing. Certain types of jigs remove fine sand.Reciprocating tables; recover fine iron particles from sand discarded by above processes.Magnetic separation; applicable to the commercial separation of the magnetic oxide of iron from gangue material. From a scientific standpoint it is possible to separate certain hematites and limonites from their gangue:(g) Miscellaneous processes; comprise dry concentration, electro-static separation and other processes."

Jan 1, 1920

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By D. K. Grubbs

Red bauxites from Breadnut Valley, Clarendon Parish, Jamaica, are very homogeneous in texture. Bauxite minerals are uniformly distributed in a groundmass, the predominant grain size being smaller than l um (Figure 1 Although the deposits have a massive, non-stratified structure, they all seem to have been affected by postformational faulting which is evidenced by shear zones running subvertically through the deposits. These shear zones stand out very clearly because of a yellow staining along their faces. Often yellow zones, ranging from a few m to several cm in thickness, have developed. When the shear zones are cut at an angle, they appear as yellow veins. Near the surface of the deposits, yellow material forms shallow irregular lenses (Figure 2). In most cases, tree roots (hair roots), or their imprints, are associated with the shear zones or stained areas. In fact, the yellowish color is especially pronounced along these roots and often disappears where the roots end (Figure 3). The mineral composition and texture of red groundmass and yellow zones are markedly different. Secondary phosphate minerals and a higher goethite to hematite ratio characterize the mineral composition of the yellow zones. It should also be noted that Al-substitution in goethite from these areas is significantly higher than in goethite occurring in the groundmass (Figure 4).

Jan 1, 1980

By John B. Pate

In a recent issue of the Mining Congress Journal, J. L. Gilliland discussed the relationship of air quality criteria, standards, and regu¬lations (1). As he pointed out, The Secretary of the Department of Health, Education, and Welfare is charged with issuing "Air Quality Criteria" which are statements concerning the concentration-effects relationship of an air pollutant. These "criteria" provide the states with a basis for their air quality "standards," which may lead in turn to emission "regulations." He further cites a list of major factors described by the National Air Pollution Control Administration, which must be considered in developing criteria. These are: properties of pollution; responses; measurement methods; exposure parameters; and characteristics of receptors. Although we briefly discuss the first two items, the principal concern of this paper is with the third item, the methods of measurements. In attempting to define responses, it has proven surprisingly difficult to establish a clear-cut cause-effect relationship between air pollutants and impairment of health. It is perhaps not too surprising that the ecological approach currently in fashion seems to be a much more powerful tool in defining cause-effects relationships. Without belaboring the point, we would like to point out that establishing such cause-effect relationships have tremendous legal and financial implications e.g., consider the possible establishment of such a relationship between pollution and inadvertent weather modification.

Jan 1, 1970

By Jaril B. Lavrencic

The unique and irregulator distribution of working places in a mine always poses the two questions: - which and how much production equipment is to be used, - what production can be expected. Since the development of analytical methods would be impractical for such cases, a lot of computer programs has emerged in recent years trying to simulate the productiom process and thus find the best answer. The usege of a simulator has its dark side well felt by the author(s) of such a program: the credibility and the confidence of the customer. Using the simulator means to respect and to incorporate all the restrictions imposed by the narow underground space, methods of production, safety regulations etc., which can turn out to become a major programming effort. If the program is not properly structured, it will be used for a single special' case only, and never again. In this paper the structure and internal mechanism of the simulator is described for which the author believes that can easily be adapted to conditions of various underground and open pit mines. MINSIM tries to reach the following rather ambitious goals: 1) Estimation of the production before opening the mine, or a part of the mine. 2) Training the personnel to make decisions. 3) Making the daily time schedules for the entire fleet of the equipment units.

Jan 1, 1989

By David M. Sullivan

Jim Walter Resources, Inc., (JWR) a division of Jim Walter Corporation, has 5 underground coal mines in Central Alabama varying in depths from 400-2500 feet. Gas Chromatography plays a vital role in safety and production at each mine. Chromatographic data is used to monitor working areas for safety and proper ventilation and to control the quality of extracted methane for sales purposes. Instruments have a1 so been employed during mine rescue operations. JWR's first Gas Chromatograph (GC) was installed in April 1984 to monitor gob gas taken from longwall gob areas and sold based upon BTU value. The GC allows maximum extraction rate of the gas within the quality guidelines. By late 1985, another system was purchased and both units were upgraded to perform an analysis of indicator gases which may appear during mine emergencies. Each unit has the ability to detect and measure the following gases at almost any level ; Oxygen (021, Nitrogen (N2), Methane (CH4), Carbon Dioxide (C02), Hydrogen (HZ), Carbon Monoxide (CO) , Ethylene (C2H4), Ethane (C2H61, Acetylene (C2H2) and a composite of hydrocarbon threes and above (C3+). The analytical run is accomplished in less than ten minutes and is completely automated. This report will introduce Gas Chromatography as applied by Jim Walter Resources for the analysis of underground mine air.

Jan 1, 1987

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC) is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub located in northeastern Utah. This paper covers the successful driving of 1,525 m (5,000 ft) of dogleg downgrade decline with a 70-ton Paurat Roadheader mining machine and a conveyor muck-handling system. Ground support is with rock bolt and shotcrete; welded wire mesh is optional. The Upper Decline of 3.89 m by 8.69 m (12.75 ft by 28.5 ft) was mined through the Uinta Formation sandstones and shales in 210 days. The sandstones have a compressive strength in the 48 MPa (7,000 psi) range with a few bands of shale up to 137.8 MPa (20,000 psi). Green River Formation dolomitic marlstone with some sandstone lenses was mined in the Lower Decline 3.89 m by 5.64 m (12.75 ft by 18.5 ft) in 175 days. The Green River marlstones are tough massive formations ranging up to 206.8 MPa (30,000 psi). Roadheaders for use on steep slopes must be modified to accommodate the particular problems associated with mining downdip. The paper concentrates on the application of Roadheaders to steep slopes and the problems of mining tough materials such as marlstone. The paper also shows the advantage of using the method of excavation on long drives.

Jan 1, 1985

By G. M. Molinda

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

Jan 1, 2008

By F. K. Letowski

Leaching of zinc sulphide concentrate by nitric acid which is simultaneously regenerated by oxygen in the reactive froth has been investigated. The reactive froth was formed by a recycled zinc sulphate electrolyte containing nitric acid, a mixture of gaseous 02 and NOx, entrapped in the foam and particles of the zinc concentrate suspended in the foam. In the reactive froth the multiple regeneration of nitric acid proceeded owing to the encapsulated oxygen and amount of nitric acid used can be considerably lower than in the continuous liquid phase. 93 to 97% of zinc was extracted to a solution containing 30 to 409/1 HNO, during 40 to 60 min of leaching in a batch reactor without regeneration of nitric acid. 50 to 100% of the consumed nitric acid was regenerated during continuous leaching in froth carried out in the ‘flotation column’-type reactor at 80 to 90°C and under pressure of 100 to 200kPa. The rate of HNO, regeneration in the froth was proportional to oxygen pressure and inversely proportional to nitric acid concentration in the froth. A two-stage process flowsheet is proposed. In the first, the reduction stage, removal of nitric acid from the leach solution directed to standard purification and electrolysis is carried out by its reduction to nitric oxide using fresh concentrate in the froth. In the second, the oxidation stage, nitric acid is continuously regenerated by oxygen in the froth.

Jan 1, 1995

By Ted M. Noskiewicz, James A. Ramsay

INTRODUCTION During the various stages of an underground project from inception through design and construction, probably the single factor of most interest and concern is the nature of the ground. The ground conditions more than any other item govern costs and feasibility; and although the methods available for assessing the ground have become increasingly reliable during the past thirty years, it is still very difficult in many cases to predict the behaviour of soil and rock during and after excavation. To help in this ground evaluation process, we have frequently supplemented the boring program with one or more large diameter inspection holes; and during the past eighteen years, seventeen of these holes have been constructed on tunnel projects which we have designed. There are references in the literature to similar inspection holes (1); however, as far as we are aware, no detailed description of them has been published. The behaviour of soil or rock during and after excavation and the effect of ground water on tunneling operations are of vital interest to tunnel designers and contractors. A comprehensive geotechnical investigation is therefore among the early and most important tasks carried out on a tunnel project and the backbone of every geotechnical investigation is the boring program. A series of borings, typically 50 to 100 mm (21 to 4 in) diameter, are drilled from which soil samples or rock core are recovered and the ground water observed.

Jan 1, 1979

By Valcana Stoyanova

The distribution pattern, abundance variations and types of polymetallic nodules and associated megabenthic communities in area covers more than 60 000 km2 laid out in the eastern Clarion-Clipperton Zone (CCZ) is presented. Our observations are based on data from 158 boxcore stations collected during the cruise of the Interoceanmetal (IOM) in 2004 on board of RV Yuzhmorgeologiya. Although those polymetallic nodules for two decades been subject to prospecting and exploration studies carried out by IOM, the knowledge of megabenthic communities and their distribution pattern within nodule field was extremely limited. With purpose to evaluate the relationship between polymetallic nodules and associated benthic megafauna, an comparison analyze was carried out in respect to their composition, types, abundance across the studied area owing into account the local particular feature of bottom topography. It is suggested that the nodule-bearing seafloor supported more diverse fauna (higher number of morphotypes) than the nodule-free areas. Moreover, based on correlation between types of nodules and associated faunal morphotypes frequency the apparent relationship is considered. The most abundant megafaunal taxa (between 68 ? 92%) is essentially associated with the occurrence of the diagenetically growth nodules type (D-type and its D1-subtype); the role of the H and HD nodule-types was variable. In respect to the bottom topography, the highest diversity in the structure of megafaunal communities was recorded in the gently undulating plains and on the horst slopes, thus the highest nodule abundance occur on the topographic slopes.

Jan 1, 2008

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By N. S. P. Kumar

INTRODUCTION Development work at Carr Fork Mine of Anaconda Copper Company in Tooele, Utah commenced in August 1974. A decision to install an underground gyratory crusher for primary crushing run-of-mine ore and waste was made in 1976. Higher throughput rates, larger reduction ratios and greater flexibility in terms of meeting immediate and expanded production needs were the main reasons for selecting the gyratory crusher over the jaw crusher. UNDERGROUND MATERIALS HANDLING Underground crushing and conveying system was designed for a capacity of 16,300 mtpd of ore and waste on a 2-shift, 5-day week basis. Engineering and design of crusher complex was performed by Anaconda engineers at Carr Fork. Figure 1 represents the longitudinal section of mine showing the general materials handling system. Mine area is trackless except for materials and production haulage which is run on rail track on both 1200 and 970 levels. Ore from stopes and waste rock from development headings are handled by 3.8 cu m (5 cu yd) Jarco scoops and dumped into 2.4 m (8 ft) diameter ore and waste passes at the 1200 level. The material gravitates down to the 970 level where it is loaded into 12 cu m (420 cu ft) ASEA mine cars using side loading chutes. The muck train, consisting of 15 to 18 cars and two 27 mt General Electric trolley locomotives, is hauled over a distance of 2,300 m (7,550 ft) to

Jan 1, 1981

By Deborah A. Kramer

Although beryllium was initially discovered in 1797, it was not until 1916 that the first significant quantity of beryllium metal ingot was produced in the United States. Before 1940, most of the small quantity of beryllium metal used in the United States was supplied by Germany. Beryllium was not used in its metallic form; it was used as an alloying addition to other metals, mainly copper and nickel. World consumption of beryllium at that time was estimated to be a few hundred kilograms annually. Because of increased tensions in Europe before World War II, imports of metal from Germany ceased in 1940, and domestic production was required to meet the needs of the military. As a result, by 1946, the United States became the principal supplier of beryllium products for the world, a condition that prevails today. Because of beryllium's high strength, light weight, and high thermal conductivity, it has been used in a large number of industrial and defense applications as a metal, alloy, and oxide. The United States is the only country other than China and the former USSR currently producing beryllium products from beryllium ores and concentrates. Bertrandite, mined in Utah, is the principal ore source of domestically produced products. Imported ore, mainly from Brazil, supplements domestic ore supplies. Production and consumption data for the United States is shown in [Figs. 1 and 2]. Production data for 1969-1979 is withheld to avoid disclosing company proprietary data.

Jan 1, 1994

By Alan E. Isaacson

Extensive gravel deposits exist within a six-county area in the mountains surrounding the Salt Lake Valley, and in the mountain ranges to the west. The six-county area includes Davis, Salt Lake, Summit, Tooele, Utah, and Wasatch Counties. The majority of these are beach deposits from prehistoric Lake Bonneville. However, real estate development associated with a projected population increase of 54 percent over the next 20 years is expected to remove most gravel deposits in Salt Lake County from consideration for mining, forcing gravel operations to relocate from eastern Salt Lake Valley to the Oquirrh and Stansbury Mountains farther west. The gravels in these ranges are of lower quality and require additional processing to manufacture asphalt and concrete. Replacing gravel resources along the Wasatch Front with resources in the Oquirrh and Stansbury Mountains over the next 20 years has the potential to increase construction costs by nearly $1 billion. The majority of this cost (82 percent) is the result of increased transportation costs due to longer distances to market. The remainder of the cost is attributable to lower quality gravels that will require additional processing in the manufacture of asphalt and concrete. The following analysis and discussion does not take into consideration the amount of crushed stone that is currently being used in the construction industry in northern Utah, its use as a substitute for lower quality gravels, or as a factor in the base case projection.

Jan 1, 2001

By E. Steel, V. S. Znamensky, A. Wylie

The asbestiform habit is most commonly developed in certain amphiboles and chrysotile, but other minerals also may crystallize with this unusual habit. The habit may be characterized by (1) a fibril structure, single or twinned crystals of very small widths (generally less than 0.5 pm), which have grown with a common fiber axis direction, but are disoriented in the other crystallographic directions; (2) anomalous optical properties, primarily parallel extinction; (3) unusual tensile strength; (4) high aspect ratio; and (51 flexibility. In addition, there is evidence to indicate that some amphibole asbestos may have unusual surface properties. ASBESTOS AND THE ASBESTIFORM HABIT Asbestos is defined as a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation, and therefore are suitable for uses where in- combustible, nonconducting, or chemically resistant material is required (Gary, et al., 1974). The most common minerals that may occur with the asbestiform habit are chrysotile, grunerite (amosite], riebeckite (crocidolite), actinolite, anthophyllite, and tremolite; although the development of this habit among these minerals is rare. Other minerals, most notably other amphiboles, can occur in this habit, but no others have been mined commercially as asbestos. All asbestos is confined to metamorphic rocks, even though other habits of the amphiboles are common in igneous rocks. Slip fiber veins are the most common deposits (South African amosite, Canadian chrysotile, etc.), but mass fiber deposits also may occur such as California chrysotile or mountain leather. Field relations and experimental data support the hypothesis that metasomatism is the dominant process in the formation of asbestos fibers, amphibole as well as serpentine. The crystal habit of a mineral is the shape or form a crystal or aggregate of crystals take on during crystallization. The asbestiform habit has a number of characteristics that differentiate it from other habits. Chief among these is the fibril structure.Afibri1 is a single or twinned crystal with a very small width, generally less than 0.5 pm, and an extremely high aspect ratio; bundles of fibrils may have lengths reaching into the cm. Fibrils share a common crystal growth direction along the long axis of the fiber, but appear to be disoriented with respect to one another in the other crystallographic directions. The structure of the individual fibrils, and the organization of fibrils within a fiber may differ among the various types of asbestos. The fibril structure of asbestos is probably a factor in controlling a number of secondary properties that include high tensile strength, flexibility sufficient for weaving, and anomalous optical properties. The high tensile strength of asbestos is quite remarkable, exceeding that of the ordinary varieties by a thousand fold (Zoltai, 1978). In part, this may be attributed to the lack of defect on the fibril surfaces (Zoltai, 19781, but some contribution also must come from the existance of bundles and the nature of the ordering of and forces among the fibrils. The flexibility is not only enhanced by the fact that the fibrils may slip past one another, but by their small widths and extreme aspect ratios. However, structural defects parallel to the fiber axis also may contribute to this property. Among the common commercial asbestos types, the greatest flexibility is found in chrysotile and the least in grunerite asbestos (amosite), varying inversely with fibril thick- ness. In addition, at least for chrysotile, composition also may affect the flexibility of the fibers. Finally, most asbestos minerals are mono- clinic, but optically display parallel extinction (Heinrich, 1965, and Wylie, 1978). This also must be due, in part, to the ordering or lack of ordering of the fibrils. The fibril structure is probably a random

Jan 1, 1986

By James E. Friant

The technology applied to shaft sinking has lagged far behind other construction activities. While surface oriented construction and mining have made great strides with new processes and equipment, the majority of shafts sunk currently still follow a drill, blast and muck-out cycle developed in the 16th century. Today, in 1979, the shaft sinking industry is in the midst of its own private industrial revolution. Millions of dollars are being spent annually by industry and government alike to spring the art of shaft sinking into the 20th century. The objective of this paper is to review a few of the newest mechanized schemes for shaft sinking. This is not a theoretical review, however, but a practical one, and deals only with hardware and projects which are currently on jobsites. Figure 1 shows the equipment. On the left is the 241SB 184, a 24 foot diameter blind shaft borer. This machine is currently at about 200 feet, constructing a coal mine shaft in Alabama. It is built and utilized in a manner similar to a tunnel borer. In the upper center is the 1211SR, a 12 foot diameter blind shaft reamer. This machine follows a 6 foot pre-drilled blind pilot hole, and is at work in Chicago. On the upper right is the 121BR, a powerful new blind drill. Just below it is the conical drill head for the 121BR which can utilize either carbide or standard disc cutters. At the center bottom is an expandable back reaming head which can be used to enlarge a drilled shaft up to a maximum of 16 feet diameter, or can be used to produce a shaft having several diameter changes. This equipment is also in use in Chicago.

Jan 1, 1979

By Charles A. Horne

Grinding mill circuits used for particle size reduction of mineral ores commonly use cyclones as primary classifiers. Typically, several individual cyclones are installed in a cluster (Fig. 1) where they can easily be added or valved-out of operation in order to balance classifier capacity with fluctuations in tonnage and recirculating loads as ore grades and hardness vary.

Jan 1, 1993

By Leslie E. Apodaca

INTRODTUCTION The use of spiral concentrators for processing fine coal particles is an old idea that has recently gained acceptance in the 11.S. coal industry. It was not onti1 the Australian Minerals Industry developed a spiral concentrator specifically for separating coal from ash in the latter 1970's and early 1980's that spiral concentrators were seriously considered as viable equipment for processing fine coal. The Wright Coal Spiral was introduced in 1980, the Mineral Deposits Limited Mark 10 Coal Spiral was introduced in 1982, and the Vickers Wyong Coal Spiral was introduced in the latter part of 1984. Each spiral design was different and utilized constant profile troughs, constant pitch troughs, compound profile troughs, and various splitter arrangements. Mineral Deposits Limited has combined the best features of the compound profile trough and constant pitch trough with critically-placed splitters to develop the MDL LD4 spiral concentrator which is a truly efficient coal washing spiral. This spiral concentrator was introduced into the U.S. Coal Industry in 1987. Recently, Mineral Engineering Technology of the United Kingdom and Multotec of South Africa have introduced their own coal spiral designs. Spiral concentrators were first installed in fine coal processing circuits in the Australian, South African, and Canadian Coal Industries in the early 1980's and in the U.S. Coal Industry in 1985. SPIRAL CONCENTRATOR SEPARATION PROCESS The separation process that occurs within the spiral concentrator trough is very complex, as it is a combination of three gravity separation processes. When the coal slurry first enters the spiral trough, each coal and ash particle and the water is subjected to centrifugal forces. These forces cause the water, light coal particles, fine heavy ash particles, and medium middlings particles to the outer vertical portion of the spiral trough. The coarse ash particles and the coarse middling particles remain on the inside of the spiral trough. The center or transitional area of the trough contains a mixture of middlings particles and near-gravity material that is present in the slurry, as shown in Figure 1. At the same time the coal and ash particles are suhjected to centrifugal forces, the trough design (both profile and pitch) causes the particles to be subjected to flowing film and stratified bed separations. The combination of these three separations, whose efficiency is dictated by the spiral troogh design, will effect the separation of the lighter coal particles from the heavier ash and middlings particles. As the slurry flows down the spiral, the profile and pitch design of the trough will counteract the centrifugal forces on the fine, heavy ash particles and fine middlings particles and cause them to migrate from the vertical portion of the trough to the center or inner portion of the trough. At the same time, any heavy particles trapped in the transitional area of the trough will be forced to migrate to the inner edge of the trough and any coal particles will be forced to migrate to the outer edge of the trough. SPIRAL SPLI'TTEP ARRANGEMENT The critical placement of splitters along the inner edge of the trough for removal of the heavy ash particles as the slurry flows down the trough further enhances the separation of the coal particles. At the bottom of the spiral trough are product splitters arranged to make a final separation of the slurry stream into clean coal, middlings, and refuse products.

Jan 1, 1988

By Ronald E. Yarbrough

As a result of concern for the citizens of the State of Illinois who owned structures above underground mine workings, the Illinois State Legislature passed House Bill 158 in 1978. This bill amends the Illinois lnsurance Code and creates the Mine Subsidence Reinsurance Fund which is an insurance pool that is to receive a state appropriation of $500,000 as "start-up" money. One hundred thousand dollars has been paid to the fund as of October, 1982. The Fund is to return this appropriation to the State and is to remain self-supporting from premiums. The Fund utilized a pre-existing institution, which also was an insurance pool, the "Fair Plan Facility" and its governing Board, consisting primarily of insurance executives, to administer the program. The Mine Subsidence lnsurance Act went into effect October 1, 1979, and the bill provides that property owners in the State of Illinois may purchase up to $50,000 of mine subsidence insurance which is attached to their fire insurance policy. The deductible is normally 2%, but cannot be less than $250 or more than $500. The annual rate structure for residential structures in 1981 for $50,000 coverage is $10 (frame), and $12 (masonry). The rate structure for commercial buildings is based on the value of the building and the rates for $50,000 maximum coverage is adjusted upward. The insurance was mandated by the State Department of lnsurance and rolled onto the insurance policies of the homeowners in 34 counties which had been recognized as having sufficient exposure to subsidence damage to be covered by the Act. One percent or more of the land surface is undermined in each of the 34 counties. In the other counties undermined in the State of Illinois, insurance is available to the homeowner upon request to the private insurance carrier.

Jan 1, 1982