Search Documents

By David W. Cannon, Russell V. Mann

In a dispersion of particles in liquid a net charge will develop at the particle-liquid interface. This surface charge is usually due to the adsorption of charged material from solution. The existence of this surface charge gives rise to the formation of the electric double layer of counter-ions which surrond the charged particle. The particle surface charge and the electrostatic repulsion which exists between similarly charged particles is the primary stabilization mechanism for lyophobic colloids (1). The separation of charge which occurs at the particle-liquid interface gives rise to several dynamic phenomena associated with colloidal systems or with solid-liquid interfaces in general. These phenomena are known as electrokinetic phenomena and the four classic electrokinetic phenomena are; electrophoresis, electroosmosis, streaming potential, and sedimentation or Dorn potential. The actual driving force for electrokinetic phenomena is not the surface charge per se, but the charge at the interface between the liquid which is hydrodynamically bound to the particle surface and the bulk fluid. This interface is known as the slipping plane or the plane of shear and the potential at this interface is the zeta potential (2). The factors linking the electrokinetic phenomena is that they involve a relative motion between the liquid and the charged particle or solid surface and the driving force is the zeta potential of the solid. In addition to the four classic electrokinetic phenomena there are two additional electrokinetic effects in disperse systems; the electro-acoustic effects. When an alternating electric field is applied to a cooloidal dispersion the particles will move in the field due to their net zeta potential. If there is a density difference between the particles and the fluid this motion will result in the development of an acoustic wave. The effect was discovered at Matec and has been termed the Electrokinetic Sonic Amplitude or ESA (3). ESA is the pressure amplitude generated by the colloid per unit applied electric field strength and has SI units of pascals per volt per meter. When an alternating pressure field (acoustic wave) is applied to a colloidal dispersion the inverse of the ESA effects occurs. A density difference between the disperse phase and the continuous phase leads to a relative motion between the particles and the surrounding liquid. This means that there will be a periodic displacement between the charged particle and the oppositely charged counter-ions in the electric double year. This displacement results in the development of an alternating dipole moment at the frequency of the applied field. This effect is termed the Ultrasonic Vibration Potential or UVP and was first predicted for electrolyte solutions by Debye in 1933 (4). UVP is measured in units of volts per unit velocity amplitude of the applied acoustic field or volts per meter per second. In 1938, Rutgers (5) and Hermans (6) pointed out that the effect would also be present in colloidal dispersions. A detailed theory for UVP effects in colloids, also called CVP, was first presented by Enderby in 1951 (7). Extensive studies of the UVP in electrolytes have been carried out by Yeager et al (8). Recently, O'Brien (9) has developed a general theoretical treatment of electro- acoustic effects in colloids and has derived a reciprocal relation linking ESA and CVP effects. The most commonly studied electrokinetic phenomena is electrophoresis. Electrophoresis is the movement of charges particles in an applied electric field. The velocity of the particle divided by the applied electric field strength is the electrophoretic mobility of the particle. The zeta potential can be calculated from this mobility (2). The magnitude of both the ESA and CVP effects are directly proportional to the electrophoretic mobility of the particles. The mobility determined by the two electro-acoustic effects is the dynamic or AC mobility of the particles.

Jan 1, 1990

By Howard G. Coopersmith

Kelsey Lake kimberlites are a cluster of eight diamondiferous pipes that occur in the northern State Line kimber lite district of the Colorado-Wyo¬ming diamond province (Coopersmith 1991, 1993) (Fig. 1). This is located at the southern margin of the Wyoming Archean province. Two relatively large pipes and a few smaller bodies define the cluster (Fig. 2). The Kelsey Lake kimberlite cluster has been developed as the first diamond mine in the United States. The cluster was discovered in 1987. Full-scale production began in the spring of 1996. Mining has produced gem-quality diamonds up to 28.3 carats in size. The 30 State Line kimberlites, intruded about 390 million years ago into Proterozoic crystalline rocks, were presumed to be underlain by Archean basement of the Wyoming Province. Nearly all the kimberlite pipes contain diamond but only the Kelsey Lake pipes are economic. The Kelsey Lake kimberlites contain predominately diatreme facies kimberlite, with minor hypabyssal and crater facies rocks locally occurring. Alteration and weathering of the kimberlites is extensive. Petrologic studies indicated an underlying lithosphere that has a largely Proterozoic signature and shows evidence of deep melt and metasomatic events. Current development has concentrated on the two largest pipes. These have been bulk-sampled after geological study (1987) identified the presence of small diamonds and mineral chemistry indicating favorable diamond conditions. A 10-t/hr (11-stph) rotary pan plant was established in 1992 to process thousands of tons of bulk-sample material. Grades and gem-quality diamonds to 14.2 carats in size were recovered. Early in 1995, it was decided to move from evaluation to commercial mining. Production began in early 1996. A 195-t/hr (215-stph) rotary pan plant was built. A water supply system and tailings disposal have also been incorporated. The project straddles the Colorado/Wyoming border. Existing mining permits were amended to incorporate the increased scale and new plant facility. The permits for this project included the following: Colorado mining permit, Wyoming dozing permit, Corps of Engineers Section 404, Colorado NPDES, Wyoming NPDES, Storm water Management Plan, Air Pollution Emission Notice, various Colorado and Wyoming State Engineer and well permits, Substitute Water Sup¬ply Plan, Larimer County Special Use Review, and US Forest Service road use permits. The temporary destruction of a wetlands area was a sensitive issue. It has been addressed through the Clean Water Act Section 404 permit administered by the US Corps of Engineers. This use will be mitigated by creating new, self-sustaining wetlands in the immediate drainage system. A comprehensive and bonded reclamation plan is incorporated in the permits. Diamond mining and ore processing is environmentally benign. No chemicals are used in processing the diamonds. The plant is a water wash facility. The kimberlite ore is inert, as is the granite wall rock. The exposure of the ore body and the subsequent ore processing and waste rock and tailings containments pose no threat of release, leaching or dispersion of any detrimental elements. There is no acid-forming waste. Even a prolonged acid rain environment will not produce a harmful leachate. Slimes containment and clarification ponds will prevent unacceptable levels of suspended solids in water discharge. The isolated, restricted access and nonvisible nature of the mine and processing has led to straightforward permitting. Geology The State Line district is located in the northern

Jan 1, 1997

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato's program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

The Sandvik Group (Sandvik AB), headquartered in Sandviken, Sweden, continues to expand its worldwide operations growth. After recent acquisitions, including Tamrock, headquartered in Tampere, Finland, the company now has annual sales of more than US$5 billion (SEK 40 billion). With the acquisition of Tamrock, Sandvik has further increased its interests in the mining industry. Sandvik Rock Tools, a familiar name in the mining industry, is one of the world's leading suppliers of rock-drilling tools. And Tamrock is one of the world's leading suppliers of drilling machinery, loaders and equipment for rock-excavation operations. Sandvik believes that the two companies combined offer customers "maximum productivity through total system solutions, including machinery, service and tools." In 1997, Tamrock posted sales of US$940 million (SEK 7.5 billion). In addition to its expertise in drilling tools and equipment, Sandvik is supported by its collective resources in specialty steel and cemented carbide. These resources include extensive research and development capabilities, with annual investments in R&D now at about US$150 million. As a result of the R&D programs, internal expansion and acquisitions, the company has nearly doubled in size during the past four years. From 1994 to 1997, nearly US$1 billion was invested in internal growth and another US$825 million has gone towards acquisitions. Return on net assets is now 22% annually. In addition to Tamrock, acquisitions of interest to the mining community include Drillmaster Inc., Houston, TX. The acquisition of Drillmaster (by Sandvik Rock Tools) has further strengthened Sandvik's position in down-the-hole drilling tools. Other major recent acquisitions by Sandvik include Kanthal, a Swedish manu¬facturer of metal and ceramic-resistant materials for electric heating furnaces, household appliances and elec¬tronics, and Precision Twist Drill, Crystal Lake, IL, one of the leading producers of high-speed cutting tools. With more than 38,000 employees worldwide, the Sandvik Group is divided into six separate business areas. Each area is responsible for its own R&D, production and sales: ? Sandvik Mining and Construction. Including Tamrock and Sandvik Rock Tools, this business area boasts of offering the most comprehensive range of "rock-working" products. These include drilling rigs, loaders, rock-excavation equipment and rock drilling tools. ? Sandvik Specialty Steel. This area includes Sandvik Steel and Kanthal, manufacturers of stainless steel tube, strip wire and bar, as well as high-alloy steel and specialty metals. ? Sandvik Tooling. This business area consists of tools and tooling for metalworking applications. Sandvik Coromant is a market leader in the development, manufacture and marketing of tools using cemented carbide, ceramics and extremely hard materials, such as diamond and cubic nitrite. CTT Tools is the world's largest manufacturer of high-speed steel tools and is now expanding operations into solid cemented-carbide tools. ? Sandvik Hard Materials. This segment produces a full range of "hard materials," ranging from cemented carbide to diamond. This area manufactures and markets a full range of cemented carbide blanks for tool manufacturers, as well as components and rolls. ? Sandvik Saws and Tools. This business area manufactures high-quality handsaws and metal saw blades, as well as hand tools ranging from wrenches to chains for logging machines. ? Sandvik Process Systems. This segment manufactures steel belts, process systems and automatic sorting systems for the chemical

Jan 1, 1998

By David L. Rife

Introduction Our society is currently experiencing a change in civil philosophy toward US industrialization. We have become increasingly bent on the pursuit of a nirvanic state of zero risk. The money supply has become inversely proportional to its sources. And most mining companies, traditionally conservative, have become increasingly risk conscious. Rising taxes, high inflation, and decades of a steadily decreasing gross national product (GNP) - coincident with moral decay and disarmament - have eroded America's economic health. Psychology of US metal markets has shifted across the economic spectrum to disillusionment and discouragement. The sagging national economy, expanding governmental debt, and a backward mineral policy in concert with worldwide unrest and turmoil have caused great volatility in the metal markets. Congressional inaccessibility of US resources has contributed to its loss in strategic leadership and dependency on foreign suppliers and the common market. Large scale mining activities are now on the decline. And there is an overall slump in mineral exploration in this country. America now faces the sobering reality of almost total importation of 13 key mineral commodities and total dependence on foreign sources for five of them. There is a growing dependency on 21 of the 34 minerals vital to the US economy. And virtually everything needed can be imported directly from third world countries. Almost 85% of the free world's supply or production of vanadium, chromium, platinoids, manganese, and titanium - an essential to the aerospace industry - comes from South Africa. That country now plays a forefront position in supplying the West with minerals. The Soviets have become increasingly aware of this situation. They have made key moves in procuring for their own purposes major raw materials markets, particularly in South Africa. This is obviously threatening to the US' direction and brings about vulnerability to shortages and cutoffs. In spite of these developments and the overall change in the mining industry, there is good opportunity for growth ahead. The way has been paved for the smaller mining companies, particularly the more bullish of these. Smaller mining organizations possess a tight management and strong sense of direction. They can easily adapt to and cope with change. "Windows" that exist in the industry directly depend on a number of factors. These include the busi¬ness climate, market research and planning, management and human resources, applied appropriate technology, favorable hunting ground, and entrepreneurship. Mining as business Mining (and exploration) as a business is by its very nature highly speculative. It involves greater risk for a longer period of time than most other businesses. The entire mineral estate in the US continues to shrink. This is primarily because of various legislated wilderness measures. Consequently, the probability of finding an economic ore deposit in the US has decayed to less than 1%. Although the risk is high, the stakes far outweigh the gamble and are larger than most other businesses can offer. Mining properties, as investments or business opportunities, can provide effective hedges against long-term inflation because the real price for selected commodities, such as gold, may sometimes rise faster than inflation. Recessionary periods seem to provide the best climate for entering the mineral business or for a particular mining organization to expand its activities. Looking ahead and seizing opportunities during a depressed market will pay off. Property payments and royalties are likely to be lower. And the potential for an upward shift in prices for a given commodity is very positive. The decision to invest in a prom-

Jan 9, 1985

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth's lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today's market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By Gary Beerkirkcher

INTRODUCTION The mine hoisting equipment that is selected and installed at a mine is for the lifetime of the mine and, therefore, it is extremely important that a proper choice be made. Several types of mine hoist designs, including double drum hoists, single drum hoists, friction hoists, and various special designs of these, are available to¬day. Each has advantages and disadvantages and they should only be used in suitable applications. Drive systems for mine hoists must be evaluated together with the mechanical systems for each hoist application. It does not make sense to properly select the hoist mechanical system and then choose a drive system that turns out to be a bottleneck. MINE HOIST TYPES There are two basic types of mine hoists available in the world today: the drum hoist, on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe) hoist, which merely passes the rope over the wheel during the hoisting process. Drum Hoists Single Drum Hoist: A single drum hoist (shown diagrammatically in Fig. 1) can be used as a service or production hoist with the cage or skip in balance with a counterweight (Figs. 2 and 3). It can efficiently service one or more levels, since the location of the counterweight at any time is not important. As a pro¬duction hoist with skips in balance, the single drum hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the single drum hoist. This has to be done periodi¬cally to compensate for rope stretch. A variation of the single drum hoist is the divided drum hoist. If multilayer winding is necessary, the single drum hoist must have a divider to allow a sep¬arate compartment for each rope. If a counterweight is used with a divided drum application, the counter¬ weight rope can be wound on a smaller diameter (Fig. 4). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are re¬duced. Double Drum Hoist: A double drum hoist in oper¬ation is shown in Fig. 5. Double Drum Hoist With One Drum Clutched: As a service hoist with cage and counterweight, a double drum hoist with one drum clutched (Fig. 6) can serve several levels efficiently. The advantage of having the clutched drum is that it allows rapid adjustment of ropes due to initial stretch. Some users may prefer the single drum hoist with manual rope adjustment, while others consider the added expense of the second drum and clutch is justified to make rope adjustments quickly. The value of this feature for a particular application should be discussed with the hoist manufacturer. As a production hoist with skips in balance for a multi¬level operation, the clutch can be adjusted for efficient hoisting from any level. Double Drum Hoists with Both Drums Clutched: There are also double drum hoists that have both drums clutched (Fig. 7). The main advantage claimed for this type of hoist is that if something happens in one of the two compartments, the hoist can operate in the other compartment to raise and lower men and sup¬plies. This feature is particularly favorable if there is only one shaft entrance to the mine. Multiple Drum Hoist: The multiple drum hoist, a South African innovation, is a type of drum hoist about which everyone should be aware. Basically, it uses two hoist ropes per conveyance which at great depths per¬mits use of smaller ropes and smaller drums. There are none in use in the United States today. However, they should be considered in very deep mines. Friction (Koepe) Hoists This hoist (Fig. 8) was introduced to the mining world by Frederick Koepe in 1877. The basic prin¬ciple of the friction hoist is that the hoist rope passing

Jan 1, 1982

By Geoff W. Seward, Charles J. Maes

INTRODUCTION The work of the metallurgical engineer engaged in developing a leach, solvent extraction electro- winning process usually begins in the laboratory and generally proceeds via pilot plant testing before finally resulting in a commercial operation. The path leading to the development of the eventual process will involve a test program on leaching in order to derive information on the amenability of the copper-bearing material to acid dissolution, under various conditions. Commonly in North America the leach process of choice is either dump or heap leaching but it may also be in-situ leaching or the treatment of mine waste- waters and bleed streams. In the past, agitation and vat leaching have also been included in the list of options. Currently the economics of copper production dictate that only material of mineralogy and grade, capable of being leached without prior milling, will lead to a viable process. This is not necessarily true in other parts of the world where grades are higher and milling costs lower and therefore this paper con- fronts all the techniques available to the metallurgical engineer in terms of the evaluation of the solvent extraction process. Understanding the objectives of a laboratory and pilot plant evaluation of a solvent extraction route is important and these are described in some detail in this paper. Of at least equal importance is understanding limitations of such a test program and this aspect of process development is also discussed with reference to the kind of equipment and experimental practices that have been shown to produce results consistent with the objectives. WHERE TO BEGIN? At the inception of a project much information is developed on the variables of the leach process and indeed in some instances the type of leach that best suits the ore to be treated is the subject of intense investigation (Wadsworth 1983). The decision to treat the leach solution by solvent extraction focuses attention on the selection of the extractant most suited to the nature of the chemical composition of the solution. A laboratory screening program will probably need to be arranged in order to assist in narrowing the options and the following is suggested for this initial screening. Selection of a Representative Leach Solution This is preferably obtained from leaching a representative sample of the ore under conditions likely to pertain in the commercial leach circuit. As the conceptualized circuit flow sheet will undoubtedly involve the recycle of aqueous solutions via the leach, then it is desirable to know the nature of and the likely level of the impurity ions in the solution as well as the concentration of copper. The other most important parameter that is required is the free acid (Anon, Acorga Analytical Method) content of the solution. As a rule of thumb, it is always true that recovery across SX is maximized as the pH of the leach solution rises. Whilst a high pH may be desirable for SX recovery, it is not always desirable for the pH (or more correctly, the free acid) of the leach to rise too high. The working range, therefore, tends to be between 1.5-2.5 pH. At an early stage in process development it is likely that a number of ill-defined conditions will exist, making it difficult to decide on typical leach conditions in which case the screening tests should be carried out using a synthetic leach solution prepared from laboratory chemicals. In doing this the copper and free content should be carefully controlled along with the appropriate addition of major impurity ions as their sulphate salts. Preparation of Suitable Organic Solutions Manufacturers information sheets on the reagents to be tested are required at this stage The information necessary to make an informed judgment on reagent performance is: Copper Uptake Value. This will indicate the amount of copper that can be extracted by a reagent as a function of its operating concentration in a

Jan 1, 1986

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thor¬ough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield reve¬nues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equip¬ment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Ar¬ranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1989

By Jeong-Heum Kim, Jan M. Mutmansky

The primary purpose of the research summarized in this paper was to experimentally investigate the performance of numerous mine ventilation network iterative solution procedures under controlled conditions to determine which procedures were most favorable in terms of number of iterations and total computational speed. The solution methods investigated included: (1) the Newton-Raphson method, (2) the Hardy Cross method, (3) the linear theory method, and (4) the second-order approximation method. The first three of these methods have been widely used while the fourth was formulated by the authors to investigate its potential for ventilation network computation. In addition to the four solution procedures, three methods for selecting the branches in the meshes and three methods for ordering the meshes for computational purposes were also studied during the investigation. As a result of these various options, a total of 36 combinations of solution methods, mesh selection procedures, and mesh ordering schemes were studied. To investigate the performance characteristics of these combinations, an identical set of 180 randomly chosen ventilation networks was used in sets of 30 networks at six different levels of complexity. Here, the level of complexity is defined as a function of the size (number of branches) and the density (number of nodes compared with the number of branches) of the network. To eliminate variations in the solution times due to differences arising from the fans, a single fan with a fixed characteristic was utilized in all the experiments. This paper will deal only with the results for the four iterative methods used to achieve solutions to the mine ventilation networks. The minimum-resistance spanning tree method for mesh selection and random mesh ordering was used throughout the analysis. The conclusions will be based upon a detailed accounting of the efficiency of each method using the total time to achieve a solution to each problem and averaged over the total problem set. However, the number of iterations and the time to complete each iteration will be studied in order to better understand the solution procedures.

Jan 1, 1991

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By Nikhil C. Trivedi, Robert W. Hagemeyer

Despite the apparently unflattering term filler, this group of industrial materials has become an essential component of many industrial products with varying degrees of sophistication. Mineral fillers are, by definition, inert materials included in a composition for some useful purpose. Included in this broad category are asbestos, barite, bentonite, natural calcium carbonates (limestone), clays, diatomite, feldspar, micas, silica, talc, and other industrial minerals. Also included in this category are synthetic mineral- derived materials such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. Mineral fillers are included in compounds to accomplish a variety of final results. Inclusion of fillers modifies physical characteristics such as hardness, brittleness, impact strength, compressive strength, surface texture, fire resistance, softening point, and electrical conductivity. Depending upon the performance characteristics of the particular filler used and the quantity of the usage (i.e., percentage added), these materials can enhance the physical and optical properties, price-performance, and appearance of the finished products. These enhancements in properties of the finished compounds are the result of properties of the fillers including chemical activity, purity, hardness, particle size, particle shape, particle size distribution, surface structure, color, density, and refractive index. This chapter will review the general usage of fillers, the rationale for their use, trends, and economic factors influencing those trends. Major using industries will be examined in detail with extensive discussion of major fillers used in those industries. The reader is referred to the appropriate commodity chapter for specific information on deposits and processing for industrial minerals. All of these same filler materials have additional significant uses based on their chemical composition or other characteristics. Cross-references for these will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 5th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and synthetic) and their more important end uses.

Jan 1, 1994

By John F. M. Sims, Charles B. Green

Introduction The gold rush to the Canadian Klondike and then to the Alaskan gold camps is legend to Americans. The early years of the century also saw flourishing hard rock mining at the famous Treadwell and Alaska Juneau gold mines and the bonanza Kennecott copper mine. Over the last two decades, rich discoveries of copper, cobalt, zinc, lead, molybdenum, tin, and silver have furthered Alaska's reputation as a storehouse of US minerals. Alaska may also contain large commercial deposits of chromite, platinum, and nickel. Yet in 1984, with the exception of the Usibelli coal mine and several hundred small placer gold mines, Alaska's mineral potential remains largely undeveloped. Uncertain 70s The 1970s were years of uncertainty for the mining industry in Alaska. The discovery in 1968 of a huge reservoir of oil and natural gas in Prudhoe Bay brought the land claims of Alaska's natives to national attention and focused interest in Alaska's resource wealth. The Alaska Native Claims Settlement Act of 1971 (ANSCA) created the regional native corporations and granted them selection rights to some 178 000 km2 (44 million acres) of Alaska's 1.5 Gin' (375 million acres) - about 12% of the state's land area. The native land selection process would take years. During this time, the status of much of Alaska's land was in question. Additionally, section d(2) of ANSCA provided for the conversion of an undetermined amount of federal lands into conservation units. These consist of parks, scenic rivers, national monuments, and wildlife refuges. The debate over the d(2) lands was long and acrimonious. National conservation groups lobbied to include as much acreage as possible within restrictive classifications, regardless of its mineral or energy potential. The process was polarized into a preservation-versus-development struggle. To many Alaskans, what was at stake was the ability to develop a viable independent economy, rather than an ongoing role as economic wards of the federal government. The resulting compromise was the Alaska National Interest Lands Conservation Act of 1980 (ANILCA). ANILCA resulted in the placement of some

Jan 1, 1985

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993