Search Documents

By Li-min Liu

The Semi-Analytical method can be used to solve a variety of problems in geomechanics and civil engineering. When it comes to layered rock strata and rock masses, it is superior to all other analytical methods. This paper presents the application of a 3-D semi- analytical method to 3-D surface subsidence and stress analysis caused by mining. In this semi-analytical method the layered elements and triangular elements ate used alternatively. Their displacement pattern, strain mahix, elastic matrix, stiffiness matrix, load matrix and stress matrix are presented. A numerical simulation program based on the semi-analytical method bas been developed using Fortran 90. This program is suitable for subsidence prediction and stress analysis of mom and pillar mining, strip longwall and mechanized longwall mining methods. It is applicable to all geological conditions and mining methods. Comparing with the finite method, this method reduces significantly the number of simultaneous equations to be solved and the amount of data preparation. It not only reduces the computer memory, but also runs faster and cost less. Key Words Semi-analytical method, surface subsidence, stress analysis, layered element, triangular prism element

Jan 1, 2002

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By Holger Witthaus

The conditions of great mining depth and multi-seam¬longwalling require a special method of rockbolting, It can be described as a control loop which is based on the elements of planning, drivage and measurement. Different planning elements such as the results of the observation of physical models, numerical programmes for calculation of stress-distribution and support success, lab and underground support testing and the knowledge of strata behaviour underground including geotechnical classification are used to get best results. The increasing geotechnical information collected during drivage of roadways are used to estimate and minimise the risks of support-overload. The repeated plan/acutal comparison during the use of roadway and continuously monitoring of support and roadways provided the opportunity of optimising support design during the process of drivage and if necessary in front and after of the longwall face.

Jan 1, 2000

By André Zingano

This paper analyses possible causes for floor heaving in room-and-pillar coal mining. The coal mines are in the southern part of Brazil, where the Barro Branco Coal Seam varies in depth from 20m to 400m, and a very thick volcanic formation overlies part of the sedimentary basin. The erosion of part of the volcanic formation causes this large range of overburden thickness, which formed large V-type valleys. The mine in study is located near the slope of one of these valleys. The mine inclined shaft is at the lower overburden thickness area of the valley and the mining is developing toward the thicker overburden area. The floor heave occurred in the crosscuts, which are parallel to the slope valley direction. Numerical modeling was applied to study the stress distribution around the openings; and fieldwork on the floor heaved entries was carried out. The geometry of mining (pillar and openings width) also was analyzed. The results showed that the very weak rock and the high horizontal stress were the causes of floor heave. As the mining gets near the valley slope, the stress distribution around the crosscuts changes considerably. In addition, the stress distribution changes as the mining goes far from the crosscut. Keywords: floor failure, room and pillar, finite element model

Jan 1, 2002

By Hani Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in Bolts) has been recently developed. The device SAFEBOLT, essentially replaces the load cell, it permits the monitoring of bolt axial load from the time of its installation underground. The SAFEBOLT system consists of a portable readout unit, connecting cable and the SAFEBOLT device, which is installed in the bolt head. SAFEBOLT can be installed on any industry standard rockbolt. No special installation method is required; the conventional method of bolt installation by the stoper or roofbolter remains unchanged. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electrical wires. Pilot tests at three underground Quebec mines were carried out and helped improve the initial design of the device connector. The paper reports on two of such pilot tests.

Jan 1, 2001

By I. Geldmacher

In-Seam Seismic (ISS) methods have been used extensively worldwide for the past 10 years to assist mine planning, espe¬cially longwall mining in coal seams. The technique is only starting to gain wide acceptance in North America where it is being applied in a much wider variety of applications than was initially considered. Surveys elsewhere have concentrated on the detection of faults (structures) in coal mines prior to longwall mining. The majority of surveys in North America has been the location of abandoned workings which were not adequately surveyed prior to closure. Modeling data based upon the lithological logs, geophysical logs and interpreted sections show whether the method will be successful prior to carrying out the survey. The surveys have been performed to locate abandoned wor¬kings from the surface and underground using both seismic reflection and transmission techniques. Data from coal seams in both Illinois and West Virginia will be presented. A second method where ISS surveys are being applied to detect old workings will be presented. The ISS tomography produces an image of the P-wave and Channel Wave velocities which is representative of the material through which the signal traveled thus identifying the location of the old workings. Data from Texas will serve as an example.

Jan 1, 1990

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By K. Itakura

Information about geostructure for effective rock bolting must be obtained before setting the bolt into rock in a coal mine roadway. Especially, rock type variation and distribution of discontinuities such as layer boundaries, and separation of strata and cracks all represent indispensable knowledge. To achieve in-situ evaluation of roof rock, we developed an MWD (measurement while drilling) system using mechanical data from a drilling machine for rockbolt. System hardware detects torque, thrust, revolution, and stroke of the machine, and software analyzes the mechanical data log and displays locations of discontinuities using Neural Network techniques. Also, this system is able to estimate roof rock 3-D geostructure for varied rock types and discontinuity distribution in cases of a drill hole array arrangement in roof rock. We conducted a feasibility study for it using hydraulic drilling at roadways of the Taiheiyo Coal Mine, Japan. Simultaneously, some core drillings were also performed to confirm system analysis data. For core samples, distribution of cracks was observed and the borehole wall was investigated by OFS (optical fiber scope). Must discontinuity locations estimated from roof logging were conformed with data obtained from core inspection. However, the core sample contained a number of cracks which were not found in the mechanical data log. This indicates that additional cracks were generated during and/or after core drilling by the influence of rotational force of the machine and water supply. Furthermore, in comparison with the OFS image, resolution of the discontinuity's log estimated by this system was clarified; that is, it is difficult to detect small size cracks (hairline cracks) from a mechanical data log and the core inspection by OFS. This paper outlines the new hardware system for hydraulic drilling machine and compares the discontinuity map obtained from the software system with drilling core inspection.

Jan 1, 2001

By E. M. Williams

The U.S. Bureau of Mines is investigating the use of in-seam seismic methods to monitor stress-induced changes in coal near the working face of longwall mines. Seismic surveys performed through a longwall panel and pillars near the face can provide valuable information on geologic anomalies, high stress regions, tailgate support performance and other conditions that could endanger miners or interrupt production. This paper describes the details of the equipment and data analysis techniques used, and the significant results obtained and their implications for ground control. Using seismic tomography, it is possible to conduct measurements on the pillar and reconstruct an image representing the internal velocity distribution. Successive measurements over several days identify changes in velocity attributable to changes in stress. Several field measurements were conducted at a western U.S. longwall mine to observe stress induced changes within the panel and pillars during mining. A permissible data acquisition system was designed to meet mine safety requirements for operation in gassy air. Certification from the Mine Safety and Health Administration (MSHA) was obtained, and this approved system was used to monitor stress changes in several pillars as the longwall face passed during first panel mining. Tomographic surveys were completed across the longwall panel to map the apparent abutment stresses ahead of mining. Velocity distributions show an increase in vertical stress across the panel from the headgate to the tailgate. Additionally. a yield zone along the face near the tailgate and the forward abutment approximately 100 feet outby the face in the tailgate side of the panel were detected. These results agree well with data obtained from other instrumentation emplaced in the panel near the tailgate. Using velocities for both compressional and shear waves, the Poisson's ratio was calculated for the panel.

Jan 1, 1994

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

By S. M. Hsiung

In late September 1984, a longwall panel in West Virginia lost 60 powered supports when the face had advanced for 250 ft. from the setup entry. An in-mine investigation showed that it was a first weighting failure resulting from inadequate Support capacity. This paper presents the results of finite element modeling, which have led to a better understanding of the first weighting failure mechanism. The dynamic impact of the first weighting failure on the powered supports is analyzed. The optimum capacity for the powered supports in order to control the roof at face area under the geological condition is discussed.

Jan 1, 1984

By David Newman

The Southern Appalachian coalfield has a long history of coal bumps that are attributable to a unique combination of topography, geology, and multiple seam mining. The high pillar stresses that generate a coal bump result from: i. mountainous topography where the overburden commonly exceeds 1,500 feet beneath ridges, ii. multiple seam mining, iii. thin interburden between active and abandoned mines, iv. thick beds of competent sandstone and sandy shale strata throughout the stratigraphic section, v. strong coal seams, and vi. irregular pillar and mining geometry in older room-and¬pillar mines. Coal has been intensively mined for more than 100 years in Eastern Kentucky, Southwestern Virginia, and Southern West Virginia. As a result, it is commonplace to have abandoned mines above and/or below active operations. Therefore, those conditions that generate coal bumps will be more prevalent in the future, as underground mining continues in Southern Appalachia. The focus of this paper concerns two coal bumps that occurred in the Kellioka seam where both undermining and overmining had occurred. The purpose of the investigation is to determine the magnitude and distribution of vertical stress that initiated the bumps, to identify bump-prone areas in the unmined reserve, and to recommend pillar centers and mining layouts to avoid future bumps. The state of stress in three vertically adjacent seams was examined using the LAMODEL boundary element program. Large, detailed numerical models were constructed of both bump areas and of the remaining unmined reserve block. The results of the numerical analyses were compared with those obtained using analytical equations.

Jan 1, 2002

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By Ismet Canbulat

The cut out distance in the continuous miner sections in South African collieries is limited to 12 m. However, this distance can be extended to 24 m by the permission of the Department of Mineral and Energy (DME). This paper investigates the risk of roof Calls associated with the extended cut out distances permitted by the DME. Extensive underground experiments have been conducted using sonic probe extensometer under various geological conditions to identify the effect of cutting distance and tinge on the stability of the workings and the performance of the support. The results showed that that the most critical parameter with respect to ground control aspects of extended cut out distance is the bord width, which determines the amount of deformation that will take place in the roof. This was confirmed by the numerical modelling. The results also showed that a significant portion of the maximum deformation in the roof takes place before the ratio of cut out distance to bord width exceeds two. This indicates that once the face is extended more than twice the bord width, the roof will stabilise, assuming that no geological discontinuity is present and that there will be no further geometrical changes in the area as a result of for example the development of an intersection.

Jan 1, 2000

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development'. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines' Mine Roof Simulator.

Jan 1, 1995

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By Vladimir Adamek

Two existing predictive methods were chosen for evaluation; an influence function (Gals Theory) and a profile function (hyperbolic). These were applied to several field measured subsidence pro¬files over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1981

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000