Search Documents

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By Peter Bauer, Klaus Gamweger

"Gas purging systems are well established in nonferrous metallurgy at multiple steps during metal production, including melting, converting, alloying, and metal cleaning. Since the kinetics of all of these stages are positively influenced by using gas purging systems the overall process benefits are substantial. In the aluminum industry, inert or reaction gases are blown into the melt using porous plugs to achieve improved metal grades, higher productivity, and more efficient energy utilization. To enable the most effective application of the process gases a complete package, termed AL KIN, was developed by RHI that includes porous plugs, refractory expertise, gas supply technology, and gas control equipment. This paper discusses the technological and economic advantages of this system and the specific benefits of fuel reduction, production time savings, decreased process gas consumption, and improved refractory service life and maintenance are illustrated using an aluminum slug plant in Austria.IntroductionIn addition to high quality production, increasing productivity is the main goal in many aluminum cast houses to maintain or even strengthen their market position. The Neuman Aluminium Group, based in Austria, North America, and based in Austria, North America, and China, is the largest slugproducer for tubes, cans, and automotive parts worldwide. Recently, a comprehensive improvement program was initiated at the Neuman Aluminium Austria slug plant in Marktl - the main factory and technological centre of the group. The principal goal of the optimization project was to increase the productivity of the strip-casting production. The investment included a gas purging system, ingot preheating equipment, a new insulated launder system, and optimized melting cycles. However, the introduction of the gas purging system was pivotal to the project and has accounted for approximately 50% of the benefits achieved. This paper describes the AL KIN gas purging technology and details the process benefits resulting from the improvements at Neuman Aluminium Austria."

Jan 1, 2009

By I. A. Ibrahim, A. K. Ismail, A. A. I. Afifi

"Synthetic rutile for paints industry is conventionally produced by a combined smelting and leaching process. Smelting process is an energy intensive step and represents economic burden in view of the increasing energy costs. Egyptian ilmenite ore containing 40% TiO2 and 38% total Fe was thus directly leached with sulphuric acid to produce eventually synthetic rutile. The process-involves digestion of the ore with sulphuric acid whereby both TiO2 and Fe are dissolved. The solution was then treated with iron powder to convert Fe3+ to Fe2+ to avoid co-precipitation of iron during the hydrolysis step. After solid/liquid separation and clarification, Fe was crystallized as ferrous sulphate hydrate by chilling. The titanium pregnant liquor was concentrated by evaporation and then hydrolyzed to precipitate hydrated titanium dioxide which was then calcined to produce synthetic rutile containing 98.6 TiO2 and 0.58% Fe2O 3. The optimum conditions of all the processing stages were determined.IntroductionSynthetic rutile for paints, welding rods and other industries could be produced from ilmenite ore by sulfuric acid leaching process. This process is a batch process and nearly 80% of all TiO2 produced in the world is made by this process [1]. Figure l shows simple block flowsheet of the process. The process involves the following stages.Digestion: In this stage, ilmenite ore is treated with concentrated sulfuric acid where both iron and titanium are converted to their respective sulfates according to the following equations:"

Jan 1, 2000

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By A. Warczok

The heat transfer coefficient between liquid slags and solid surfaces is important for the design and operation of metallurgical reactors. An experimental technique developed for the purpose of measuring the heat transfer coefficient between liquid slags and solid metals is described. During the initial heating up of a Ni cylinder upon immersion in a liquid slag, a layer of frozen slag initially forms, then melts. The heat transfer coefficient measured during the initial rapid heat-up of the Ni cylinder, is approximately twice as high as the heat transfer coefficient measured during the final heat-up of the Ni cylinder subsequent of the liquidus temperature of the slag. The technique was tested in various melts i) NaNO3, ii) NaCl, iii) Na3AlF6 and iv) 2FeO*SiO2, giving consistent results. It was found that the heat transfer coefficient increases with increasing bath superheat and stirring. The heat transfer coefficient during the heating up following complete remelting of the frozen slag, is related to the slag superheat(AT) and the specific stirring energy(W) per kg of slag(E) as follows.

Jan 1, 1993

By Cecil Harriss

Philip Environmental Services Corporation's (Philip's) innovative fluidized bed thermal desorption system recovers mercury from contaminated soil. Referred to as the Thermal Recycling System, Philip has constructed a mobile thermal desorption system that has a processing rate up to five tons per hour. The system includes a continuous-feed system, all radiant heat, inert gas atmosphere, hot gas filter, two-stage cooling, and a water treatment system. Based on treatability studies, the processed soil can meet cleanup objectives as low as two milligrams per kilogram and passes the mercury toxicity characteristic leaching procedure test.

Jan 1, 1996

By S. S. B Wang

Zirconia-based ceramic materials have potential applications in high temperature furnace insulation, hot extrusion and casting dies, pressure nozzles, cutting tools, engine parts and electronic materials. High purity and superfine powders of zirconium oxide (baddelyte) were synthesized from a solution containing zirconium oxychloride and urea under hydrothermal conditions. crystallization of the metastable tetragonal zirconia using magnesium oxide or yttrium oxide as stabilizing agents was successfully achieved. The mechanism of hydrothermal reaction to produce these powders are discussed.

Jan 1, 1989

By R. W. Smith

A microorganism will function as a mineral flocculant if it is to some degree hydrophobic and can attach itself in some manner, such as through electrostatic interaction, to the fine mineral particles to be flocculated. The present paper concerns the use of a hydrophobic bacterium, Mycobacterium phlei, as flocculating agent for phosphate slimes. Experimental work on the flocculation of phosphate slimes and of dolomite and clay mineral suspensions was performed. It was found that M. phlei functions as an excellent flocculant for a dolomitic slime but does not function as well for mineral suspensions where large quantities of the solids are finer in size than the approximately 1 µm size of the bacterium.

Jan 1, 1992

By Cassandre Nowicki, Louis Gosselin, Carl Duchesne

"Quebec's primary aluminium production industry consumes roughly 39 TWh of electricity per year and is accountable for roughly 7 million tons of CO2 equivalent. By tapping only a small portion of waste heat and integrating it inside the production facility itself, we can significantly reduce GHG emissions and energy consumption. Although the amount of thermal waste can be adequately estimated by applying an energy balance to production processes, this provides very little information on the quality of waste heat and its potential for integration. A measure of exergy is required. Waste heat streams characterized by high exergy content may generally offer valuable incentives for recovery and integration. More generally, exergy values limit integration possibilities. An exergy analysis is provided for the aluminium electrolytic reduction process. This is meant to guide future heat recovery initiatives and energy efficiency measures.IntroductionCanada is one of the world leaders in primary aluminium production and 92% of its aluminium production capacities are located in the province of Quebec. In 2007, production capacity reached 2,786,000 tons in Quebec alone. Since it is estimated that 2.5 equivalent tons ofCO2 are released for each ton of aluminium produced in Canada, Quebec's aluminium production industry is accountable for roughly 7 million tons of CO2 yearly [1, 2]. Furthermore, with an average electricity consumption of 14 MWh per ton, primary aluminium accounts for 39 TWh of electricity per year in Quebec and this energy consumption represents 350 thousand tons ofCO2 equivalent [3, 4]. Natural gas consumption associated with primary aluminium production accounts for less than 1 TWh, but it represents an additional 350 thousand tons of CO2 equivalent [ 4].This work is meant to provide a tool to guide future efforts towards heat recovery and energy efficiency in the primary aluminium industry. Waste heat recovery and thermal integration can cut down both energy consumption costs and GHG emissions. In a primary aluminium production facility, waste heat represents roughly half of the energy input into the Hall-Heroult process. Tapping only a small portion of this energy could reduce natural gas and electricity consumption significantly. In order to evaluate how much of this energy is actually usable, we propose to apply an exergy analysis to individual transformation processes in an aluminium production facility, such that a potential to do work can be assigned to every waste heat flux. The approach will be described in the next section."

Jan 1, 2012

By V. Baltazar

The behaviour of arsenic and antimony during copper electrorefining was studied in order to identify the conditions under which good quality copper cathodes could be produced from anodes with high levels of these impurities. Examination of the effect of current density over the range 21 to 37 mA/cm2 indicated that the relative amounts of As and Sb entering the electrolyte affected the onset of passivation. When the ratio of As/Sb entering the electrolyte was greater than 2, the anodes showed no sign of passivation even at the highest current density; when the ratio was less than 2, the anodes passivated at 37 mA/cm2. Cathode analyses showed that anodes with an As/Sb dissolution ratio less than 2.0 tend to produce cathodes of inferior quality even at normal current densities (25.7 mA/cm2). The criterion of a minimum As/Sb dissolution ratio of 2.0, and mathematical correlations for the distribution of As and Sb between the electrolyte and slime developed in a previous study, allow the calculation of the maximum allowable Sb level in en anode for a given As concentration. Analyses of plant data at the CCR Division of Noranda Inc. for the last four years of operation have demonstrated that the use of this as a quality control tool has allowed the quality of copper cathodes to be maintained despite a significant increase in the average Sb levels in anode receipts.

Jan 1, 1987

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By Carlos G. Levi

"The principles involved in the rapid solidification of supercooled metal droplets and existing numerical models are reviewed. The limitations of these models for studying alloy solidification are discussed in terms of the effects of alloying elements on the relevant heat transfer, thermodynamic and kinetic parameters. Analysis of the enthalpy-temperature diagram reveals how the extent of rapid solidification is hindered by the addition of solute. A solidification model incorporating thermodynamic and kinetic relationships into a Newtonian heat transfer formulation is used to analyze the thermal history and concurrent solute redistribution during recalescence. IntroductionIt is well acknowledged that microstructural evolution during solidification is intimately associated with the thermal history of the liquid-solid interface. Structural parameters like chemical homogeneity, morphology and size scale of the phases can be related to the interfacial temperature and velocity. These in turn change by the interaction of the interface with the thermal and solutal fields in its neighboring environment.The thermal history of powder solidification can be conveniently described on the enthalpy-temperature diagram for a pure metal shown in Figure 1 and discussed in detail elsewhere [1). A system can conceivably follow any path of decreasing enthalpy in the supercooled region of Figure 1 (~ < 1), starting at the nucleation temperature (oN < 0) on the liquid line, and ending at some point on the solid line. A vertical path represents an isothermal transformation, of which a limiting case is solidification without significant barriers to nucleation and growth, with the interface at the equilibrium temperature TM (path one in Figure 1). A horizontal path represents isenthalpic (or adiabatic) solidification whereby the system could form an amount of solid proportional to the initial supercooling of the liquid without further heat loss to the environment. A liquid that can completely transform to solid under adiabatic conditions is said to be ""hypercooled""."

Jan 1, 1986

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients&apos;, lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By Sunil Jayasekera

This paper describes the results of a study carried out to examine the feasibility of electrolytic recovery of silver from cyanide leach liquor generated from a Western Australian silver mine tailings using a novel high mass transfer electrowinning cell. The proposed circuit involves heap leaching and electrowinning in a closed loop. The filter-press-like closed electrode arrangement of the cell allowed much improved mass transfer of metal ions to the cathode surface, making direct electrowinning of metals from dilute solutions feasible. The tests were conducted both in the laboratory and at large scale using a prototype with ~1.0 m2 cathode area. The results showed that the recovery of silver from as low as 250 mg L-1tenor was feasible. The silver deposit produced with the prototype cell was non-adherent and powdery and could be readily removed from the closed cell. A system was developed so that silver powder was discharged continuously during the run.

Jan 1, 2003

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By Antoine Allanore, Luis A. Ortiz, Donald R. Sadoway

"The steelmaking industry has drastically reduced its energy consumption in the last fifty years, and today’s technologies are considered to operate at their optimal efficiency with respect to energy needs. To cope with new constraints related to greenhouse gas (GHG) emissions, a change of paradigm is necessary. One of the promising technologies that could be deployed to help reach CO2 mitigation targets relies on the intensive use of electricity: molten oxide electrolysis (MOE). This paper presents the key process parameters that need to be tuned to address the practical needs for both high productivity in a steelmaking reactor and for an energy efficient process. Herein we show that contrary to common perception, the electrolysis process for ironmaking requires less energy than today’s chemical reduction route. Furthermore, we prove that most of the energy that must be provided to operate the electrolytic iron production cell is thermal energy which is readily generated by joule heating during electrolysis due to large currents being passed through the electrolyte. The energy consumption of the electrolysis cell is therefore shown to be highly dependent on the cell configuration and the chemistry of the electrolyte. As a consequence, the CO2-impact of the technology strongly depends on both the power production mode and the technological choices for design of the process, including cell configuration. Surprisingly enough, even when the electricity generation is not carbon-free, MOE still appears to be viable from the perspective of reducing GHG emissions providing sound reactor design considerations are made.IntroductionIn the context of greenhouse gas (GHG) emissions mitigation, the steelmaking industry is considering several techniques that could sustain the efforts and progress achieved by this sector in the last decades [1]. A recent report [2] on potential routes for low-CO2 steelmaking highlighted for all techniques both the strong dependency of CO2 emissions on electric power production mode and the need for a decrease in energy consumption per tonne of steel. Incited to innovate with respect to this last criterion, the steel industry considers electrolysis to be a promising technological solution, and in particular the molten oxide electrolysis (MOE) process. This process conducts electrolysis in a mixture of oxides that dissolve the iron oxide feed, which by the action of electric current is decomposed into liquid iron and oxygen gas. The opportunity for reduction in energy consumption during steelmaking by MOE is commonly attributed to the “direct” pathway from iron oxide to liquid metal offered by the use of a molten oxide melt and operation at a temperature above the melting point of iron, ideally 1600°C, to provide enough superheat for tapping the molten iron product:"

Jan 1, 2011

By Kenichi Moriyama

The Sumitomo Toyo Copper Smelter started operation in 1971, as an epoch-making smelter at which 9996 of the charged sulfur could be captured. In the past ten years, the amount of treated copper concentrate has-been increased from 1,300 l/ day to 1;900 t/ day by the extremely effective application of the oxygen enrichment for a flash smelting furnace and converter furnace. The sulfuric acid production capacity at the acid plant has also been increased up to 1,900 t/ day corresponding to the increase of copper concentrate smelting rate without installing an additional acid plant. Furthermore the sulfur fixed ratio is kept at a high level, more than 99.996. despite the SO. strength fluctuation of the wide range of 596 to 1396 which is attributed to the combination of flash smelting furnace and, P.S. converter. These -operational results at the? acid plant were achieved by several modifications. and two examples are briefly described as follows; (1) Converter modifications in order to cope with the high SO, strength -gas (2) Introduction of the anodically protection shell and tube type acid coolers In addition. the quality of sulfuric acid has been positively increased. For example, the concentration of iron and arsenic, which were the main Impurities in ?sulfuric acid, was successfully .reduced.

Jan 1, 1995

By R. M. G. S. Berezowsky

Treatment of Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) zinc concentrate in the Sherritt zinc pressure leach process produces a residue containing elemental sulphur, residual sulphides, precipitated iron species, si1ver and gold. Flotation of the residue recovers most of the elemental sulphur and residual sulphides to the concentrate, leaving iron oxides and bask sulphates in the tailings. The tailings also contain most of the sflver and some gold. Direct cyantde leaching of the oxide tailings (220 g/t Ag, 1.4 g/t Au) was capable of leaching most of the gold, but only a minor portion of the silver. This paper reports testwork, conducted by Sherritt on behalf of HBM&S, to define a process for a high recovery of the precious metals from the oxide tailings. A si1ver enhancement treatment, consisting basically of digestion of the residue with lime at 90°C to render the silver amenable to enhanced recovery by subsequent cyanidation, was selected as the most promising approach. Batch silver enhancement and cyanidation tests showed that treatment of the oxide residue with 80 kg/t CaO at 90°C for 1 to 2 h increased the silver extractability in subsequent cyanidation from <20% to 96%. A 96 h continuous miniplant test (1 kg/h solids feed rate), of a circuit including a silver enhancement treatment step followed by conventional cyanidation and carbon in pulp silver and gold recovery, confirmed metal recoveries to the carbon of 90% Au and 96% Ag. Reagent consumption rates were 1ess than 100 ?kg/t CaO and 5 kg/t NaCN.

Jan 1, 1990