Search Documents

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By Takahiko Okura

Most non-ferrous raw materials are associated with sulphur. To extract the metals, the sulphur is recovered typically as Sulphuric acid or liquid S02. On the other hand, natural gas may contain over 20% of hydrogen sulphide (H2S) and a huge quantity of elemental sulphur is produced through oil and gas refining processes in the world. A large fraction of the sulphur mined from natural sources is eventually returned to the earth as fertilizers, by-products of desulphurisation and neutralisation processes, or as fugitives to the atmosphere. However, the supply and demand for sulphur are in imbalance. Such situation urges to develop a new smelting process without sulphuric acid production. This paper briefly reviews the global sulphur balance and the technologies for recovering elemental sulphur. The core of this paper is a proposal to convert S02 gas to elemental sulphur by using organic materials. Some results of thermodynamic calculations and experiments are presented.

Jan 1, 2003

By John A. Herbst, William T. Pate

"Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen, and the coordination of all unit operations in pursuit of the highest performance level. However, several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of unit operations to account for critical interactions within and between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significaritly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated with the models and can be effectively optimized. Financial goals seems to be the objectives of choice.This paper discusses recent progress in overcoming the challenges and illustrates a promising approach which is being pursued at Mexicana de Cobre's La Caridad copper ore concentrator. At M de C, advanced control strategies have been installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, increased from 76,000 tpd to 90,000 tpd. Plantwide integration is expected to gain an additional 3% improvement in profitability."

Jan 1, 1996

By Guo Chen, Xuefeng Liao, Tu Hu, Shengzhou Zhang, Hongying Xia, Jinhui Peng, Libo Zhang

Pine nut shell is as raw material for preparation of high surface area activated carbon (HSAAC) by microwave induced KOH activation. The effects of microwave power, activation duration and KOH/C mass rate (R) on the iodine adsorption capability and activated carbon yield were investigated. Additionally the surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms and SEM. The operating variables were optimized utilizing the response surface methodology and were identified microwave power 738W, activation duration 17 min, and R 4, corresponding to a yield of 46.28 % and an iodine number of 2154 mg/g. The key pore structure parameters of HSAAC such as the Brunauer–Emmett–Teller (BET) surface area and total pore volume were estimated to be 3819 m2/g and 2.09 mL/g, respectively. The findings strongly support the feasibility of microwave heating for preparation of HSAAC from spent pine nut shell by microwave induced KOH activation.

Jan 1, 2016

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000

By Gary R. Adams

Coating thickness control is typically difficult with touch-up solders for galvanized steel, and corrosion properties and abrasion resistance are sometimes poor. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with zinc-tin based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix The mouldability was dependent on the microstructure of the starting material, and optimum structures could be obtained through control of casting solidification rates and/or by the addition of small amounts of copper. Hardness and preliminary corrosion test results showed potentially good mechanical and corrosion behaviour. The absence of toxic materials ensures environmental friendliness. Comprehensive performance testing is continuing on selected experimental zinc-tin-copper touch-up solders.

Jan 1, 1992

By S. P. Ball

A major limitation to maximising the rate of gold extraction in commercial operations occurs as a consequence of the limited solubility of oxygen in cyanide liquors. The use of additions of solid inorganic peroxides as an in-situ supply of oxygen to the lixiviant has been studied, in particular in its application to heap leaching. Experimental studies showed-that the release of oxygen into solution from these peroxides is very sensitive to solution pH. Agitated leaching tests showed that, when either Ba, Ca or Sr peroxides were used as the-sole source of oxygen, both the rate and extent of gold extraccion was enhanced. Column leach tests were used to simulate heap leach conditions. These showed that significant increases in the rate of gold extraction could be achieved by additions of calcium peroxide, made to the ore, prior to it being loaded into the columns.

Jan 1, 1989

By Metehan Erdogan, Ishak Karakaya, Fuat Erden

"Mg-Ni system draws attention due to the promising hydrogen storage properties of Mg2Ni. The proposed method involves the use of NiO and MgCl2 in an electrochemical cell to from Mg-Ni intermetallics directly. The electrodeoxidation of NiO was followed by combination of Mg and Ni in molten salt electrolytes. The products were characterized by XRD analysis and SEM examinations. The quantitative results from Rigaku supported by Rietveld Refinement method conducted by Maud showed that more than 50 percent of the input Ni was converted to Mg-Ni intermetallics.INTRODUCTIONIt is well known that fossil fuels are the most common energy producing materials throughout the last century although, they are not renewable and their usage cause critical environmental problems [1, 2]. Hydrogen, on the other hand, is known as a clean, renewable energy carrier and instead of fossil fuels; usage of hydrogen for energy production will be the benefit of mankind. However, there are problems that hinder more common usage of hydrogen such as hydrogen storage [3]. Mg2Ni is known as Mg based hydrogen storage material with high hydrogen storage capacity [3-6]. Common Mg2Ni production methods are; mechanical alloying [8-11], vacuum induction melting [12, 13], vacuum arc melting [14], combustion synthesis [15], melt spinning [16], repetitive rolling [17] and isothermal evaporation casting [18] were also used. However, in all of these, pure Mg and Ni are required to be produced previously. Therefore, difficulties arise during handling, preparation and combination of Mg and Ni due to highly reactive nature of especially magnesium (i.e. oxidation of Mg) [11, 17, 19, 20]. Although hydrogen desorption dynamics can be significantly improved with usage of nanostructured Mg2Ni [7], it is difficult and it requires very long processing durations to produce nanostructured Mg2Ni by above processes."

Jan 1, 2014

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill as an aid in predicting the effect of corrosion on minerals and how this effect relates to downstream processing. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5% of the total grinding media wear in the operations studied.

Jan 1, 1987

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would be reduced at the new smelter to about a half of the sum of those from previous two 1 smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive offgases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By Stephanie Trant

Montana Tech has been engaged in fundamental research on the processing of critical materials for more than a decade. Efforts include examining novel reagents for the flotation of Rare Earth Minerals (REMs). For this paper, research results on a collector, salicyl hydroxamic acid (SHA), are presented. Various REMs were examined and include the rare earth oxides (REOs), carbonates (RECs), and phosphates (REPs) of a suite of Rare Earth Elements (REEs). Differences are attributed to solution and surface chemistry, coordination number, and ionic diameter. SHA adsorption follows an ion-exchange process that leads to chemisorbed and surface-precipitated states, depending mostly on pH. Many effects are directly attributed to lanthanide contraction. Results should also be applicable to other REM/collector systems and further suggest that REM flotation should consider dual collectors.

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By Jillian Spindura

This work investigates the carbothermic reduction of the complex sulphide mineral, pentlandite, in the presence of lime. The effects of change in temperature and the use of different carbon sources are studied and the role of these variables on the reducibility of pentlandite mineral is discussed. The microstructures of the heat-treated pellets are examined using X-ray diffraction and scanning electron microscopic techniques. The latter analytical method also allows any variation in the morphology and composition of the metallic phases formed, with temperature, to be considered. The kinetics of the reduction process is studied and the magnitude of the overall activation energy is determined from the plots of percentage reduction versus time.

Jan 1, 1996

By Ing. R. Geutskens

Zinc-bearing dust from blast furnace gas-scrubbing operation is a well known environmental health problem in the iron and steel industry. Hoogovens IJmuiden (The Netherlands) developed processes to solve this problem. 90% of the zinc is concentrated in 25% of the dust (the fine particle fraction) by means of slurry-hydrocyclonage. The resulting fine particle fraction is treated in a pressure leaching process. Hydrochloric waste pickle liquors have been used as a leaching liquor. By creating optimal leaching conditions more than 98% of the zinc is brought into an acid' solution, whereas nearly all the iron remains in the residue. The zinc can be separated selectively from the solution. The residue can be reused in the blast furnace (via the sintering plant). In the article information is given about the research work and -results of the pressure leaching process as well as the possibilities of the process for solving comparible problems.

Jan 1, 1990

By Tao Zeng, Jianchao Li, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"The densities of the selected quaternary Ca0-5%Mg0-Alz03-Si02 slag with low silica were measured by the Archimedean method in a wide temperature range from l 723K to 1823K. Slag compositions were chosen based on five different levels of Si02 content between 0.00 pct and 11.40 pct. The MgO content was equaled to 5.00 pct. The mass ratio of CaO/Alz03 was varied from 0.67 to 2.14. The effects of temperature, Ca0/Alz03 ratio and optical basicity were studied. It is shown that density decrease approximately linearly with an increase in temperature. With the same Si02 content, the density decreases with increasing of CaO/Alz03 ratio and optical basicity. Based on the experimental data as the boundary of the homogenous phase region predicated by F ACTSAGE software, the mass triangle model is used to calculate the density of selected limited homogenous phase region. The results showed that the mass triangle model is working well.IntroductionIt is of great importance to measure density of slag melt not only to the theory research for melt, which that is directly amenable to the structure correlations of molten slags, but also to the industrial application. Many metallurgy phenomena such as inclusion formation in molten melt and its removing, slag foaming, slag-metal reaction are closely related to the density of slag. Density is also required to estimate other fundamental properties, like surface tension, viscosity, and thermal conductivity from thermal diffusivity so that a relatively complete picture in regard to the behavior of high-temperature molten oxides could be made."

Jan 1, 2013

By M. D. Stephens

A new, one-step process for extracting titanium from titaniferrous materials has been demonstrated. In the process, depleted uranium tetrafluoride (DUF 4), a solid, is mixed with ilmenite (FeTi03) and heated to 900°C. Titanium is extracted in the vapor phase as titanium tetrafluoride (TiF4) and the DUF4 is converted to uranium-iron oxide. The process has been found to selectively fluorinate the titanium in ilmenite and is capable of producing high purity TiF 4 with very low iron content. TiF 4 can be collected by condensation or through reaction with a fluoride salt such as NH4F, KF, or NaF. The TiF4 produced from the process can be used to make titanium metal, titanium oxide, or fluorotitanate compounds. Since the fluorination process is highly selective for titanium, it avoids many of the separations and waste issues common to other titanium extraction processes.

Jan 1, 2001

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By Mikiya Tanaka

This paper outlines our attempt to establish a recycle process of nickel in the spent baths and waste rinse water of electroless nickel plating plants using solvent extraction and solvent-impregnated support, Solvent extraction studies of nickel from actual spent baths revealed that (i) nickel is efficiently extracted by a hydroxyoxime extractant such as LIX84I at a pH greater than 6 and is readily stripped with sulfuric acid, and (ii) the mixtures of LIX63 and acidic organophosphorus extractants (D2ERP A, PC88A, and Cyanex 272) enhanee the nickel extraction efficiency to a sufficient degree without pH adjustment, but at the same time, reduce the stripping efficiency. The application of acidic organophosphorus extractants to selectively remove impurity metal ions (iron and zinc) from a real spent bath before extracting nickel lead to the finding that PC88A and Cyanex 272 effectively remove iron and zinc without pH adjustment leaving nickel in the raffinate. The removal of nickel from the waste rinse water was also studied. Solvent-impregnated supports with a macroporous resin and oil sorbents made of natural kapok fiber and synthetic fiber as supports were applied using D2EHPA and LIX860 as the extractants. During the batch operation, nickel is removed with a high efficiency without pH adjustment. During the column operation, however, the effective removal is hindered by (i) the dissolution of the nickel-D2EHPA complex into the aqueous phase in the high loading region, and (ii) the slow removal rate of the LIX860-impregnated support.

Jan 1, 2003

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016