Search Documents

By Helena Byrdziak

KGHM Polska Miedz S.A. is a significant European copper producer with production of 447,000 mtpy, operating three underground mines and three smelters. The company has been involved for years in environmental activity, which was stimulated not only by the company itself, but by the development of environmental regulations as well. The first set of regulations, concerning water protection, was' established in Poland' in 1974, while a comprehensive environmental law was passed in 1980. This law in general requires industry to submit all data of environmental significance to the local authorities. Based on this data, they establish limits concerning emissions into the air, water and ground, the amount of wastes produced and the means of their disposal. A company has to pay fees for each tonne of emitted substances and stored wastes. When the emission of a substance exceeds the limit, the company has to pay a penalty which is about ten times higher than the fees. This approach in general is effective because it forces companies toward: reduction of their emissions. The problem is that the law is constantly subject to change and is becoming not only more restrictive but is involving more and more bureaucracy.

Jan 1, 1999

By Takashi Nakamura, Kenji Oosumi, Kazuhisa Fujisawa, Takayuki Kogishi

"Recycling of used aluminum beverage cans(UBCs) is one of the important issues for aluminum manufacturer presently. The direct re-melting of UBCs shows two problems. One is a reduction in molten aluminum recovery and the other is a contamination of other metals such as Ti and Fe from paints. Both problems are caused by paints coated on the surfaces of aluminum cans. Removal technique of the paints, therefore, has been required. Although roasting and shot blast techniques have been developed, both were not successful in removing the paints effectively. A swell-peeling method has been applied to remove them using a methylene chloride solution with acids and it works very well. Small laboratory scale tests have been carried out to develop the commercial process and clarify the mechanism of the swell-peeling method in the present study.When the surface area of UBC is more than 10 cm2, peeling time is independent of the surface area, about 60 seconds, because swelling phenomenon is controlled by the penetration of the liquid through the fine pits on the surface of the paint. This is good for a commercial process. Peeling takes place when the swelling force generated by methylene chloride exceeds the adhesion force between the film and the surface of aluminum, that is weakened by the coexisting acid, especially halogenated acetic acid."

Jan 1, 2000

By Chao Zhang, Kexin Jiao, Yi Qian, Jianliang Zhang

Now low-grade iron ore were widely used. However, one prominent problem is that the content of trace elements is higher than that in high quality iron ore. For the requirement of the content of Mn, Cr, Ni, Cu, and Ti in hot-rolled steel sheet and strip, the upper limits of these elements in sinter will be studied in this paper. Using the activity model of aggregation of electronic phased slag composition, the distribution ratio of each element in converter is analyzed and the content of each element in hot metal is calculated. Furthermore, through the thermodynamics method, the distribution ratio of each element in BF is analyzed and the content of each element in raw material is calculated. The upper limits of Mn, Cr, Ni, Cu, and Ti in sinter can be determined by calculating, the values are as follows: Mn 0.767%; Cr 0.552%; Ni 0.055%; Cu 0.159%; Ti 0.108%.

Jan 1, 2015

By Mahesh C. Jha

Molybdenum, a major refractory metal, is widely used as an alloying element in steels and superalloys to improve their corrosion resistance, physical properties and mechanical strength, particularly at elevated temperatures. The current worldwide production and consumption is estimated at about 130,000 tons contained molybdenum per year. Molybdenum occurs in nature as molybdenite mineral and is recovered by a flotation process as a primary concentrate at molybdenum mines and as a byproduct concentrate at copper mines. The concentrate is roasted to a technical-grade molybdic oxide (tech oxide) in multiple-hearth roasters. About 80 percent of the tech oxide is sold, as such or after conversion to ferromolybdenum, for addition to iron and steel. The remainder is further refined to pure oxide and molybdate chemicals that are used in the manufacture of catalysts, specialty chemicals, molybdenum metal and superalloys. This paper discusses the various steps in the extractive metallurgy of molybdenum, from flotation of sulfide concentrate to reduction of pure oxide to molybdenum metal.

Nov 26, 1999

By Pascal Gardin

The purpose of the paper is the mathematical modelling of flows inside steel continuous casting mould. For CFD validation of flow oscillation prediction, unsteady calculations with a realizable k- model were performed in a billet caster with rectangular section. Self sustained and regular oscillations were obtained. Calculated flapping frequency is very close to what is mentioned in literature. For slab caster configuration, flow oscillation is influenced both by lower roll, which creates very small frequency oscillation (0.012 Hz for our water model), and upper roll, which creates slightly higher frequency oscillation (0.05 Hz). The two rolls interact and it is possible to detect both frequencies in the nozzle jet region. Numerical results are in good agreement with measurements for fluctuating velocity spectra and provide explanation for interaction of rolls. To improve flow stability inside the mould, it is established that gas injection in the nozzle has a very positive effect.

Jan 1, 2006

By S. C. Sharma

The aluminium matrix composites with ceramic dispersoids can be separated by density difference concept. In the proposed work composite scrap is recycled using an oil fired furnace. The scrap is melted in the furnace and temperature is maintained below 740 degree centigrade. Because of the density difference the lighter dispersoids will float and heavier dispersoids will settle down. The clean melt is separated be removing the floating and settled disperssoils, and then filtering using ceramic filters.

Jan 1, 1995

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By James A. Sommers

Hydrolysis of NbC15 is used to recover oxide values for ceramic and metals production. Reaction of NbC15 with water is rapid, exothermic and vigorous, yielding a gelatinous slurry. In contrast, dissolution of NbC15 in 12 N HCl is endothermic, resulting in a clear yellow solution. Such solutions can be de-hydrochlorinated by controlled contact with air, to precipitate a tantalum¬rich solids, depleting the liquid of its tantalum content. In this way, cheap, useful Nb-Ta partial separation is achieved. The separation is based upon differential oxide-chloride stability. Nb2O5 with <200 ppm Ta/Nb has obtained from starting levels of 2000 ppm. Observations are made on the different types of hydrolysis.

Jan 1, 1992

By Yong Xian, Zhaohui Sun, Honggang Zhong, Qijie Zhai, Jie Sun

Vacuum refining is admitted as an effective means to remove impurities in the process of alloy smelting. In this paper, Orthogonal and single factor experiments were carried out to investigate effects of multiple factors, such as superheat degree of the melt, degassing time and vacuum degree, on the vacuum refining process. The results showed that the best removal rate of oxygen and nitrogen is up to 82.71% and 61.3%, respectively, due to high vacuum degassing efficiency. It is found that the superheat degree is minimal impact on the deoxidization rate, in addition, nitrogen removal is controlled by the degassing time. The inclusions exist in the AlV55 alloy are mainly composed of oxides and vanadium-nitrogen compounds.

Jan 1, 2015

By I. K. Chopde, M. M. Dhobe, C. L. Gogte

"The quality of machined surface is becoming more and more important to satisfy the increasing demand of component performance and its reliability. While machining any component, it is necessary to satisfy the surface integrity requirements. Heat treatment plays an important role in improving the characteristics of the material.This work investigates the effect of heat treatment on the surface characteristics of AISI D2 tool steel after Wire-Electro Discharge Machining (W-EDM). The test specimens were prepared by hardening and tempering and then machined with Wire-Electro Discharge Machining process. Optical and scanning electron microscopy, surface roughness and micro hardness tests were conducted to study the surface characteristics of the machined surface. After characterization based on microstructures and test results, it is observed that the recast layer droplets are of smaller size with reduced white layer thickness resulting in higher hardness and lower surface roughness.IntroductionWith the development of mechanical industry, the requirement of alloy materials having high hardness, toughness and impact resistance is increasing. At the same time the quality of machined surface is becoming more and more important to satisfy the increasing demands of component performance and reliability. When machining any component, it is necessary to satisfy the surface integrity requirements. Surface integrity has two important parts. The first is surface texture, which governs mainly surface roughness. The second is surface metallurgy, which concerns to the nature of surface layer produced in machining [2]."

Jan 1, 2012

By Leonel Contreras

The gas treatment system, MALIGAS (in Spanish MAnejo y Llmpieza de GASes which means handling and cleaning of gas), is part of the Codelco-Chile Potrerillos Smelter decontamination plan; which includes the newly designed system for the cooling and cleaning of the gas generated from a Teniente Converter and four Peirce Smith Converters. The gas generated in the process is captured by water cooled hoods and mixed with air. Then the gas enters a cooling pre-chamber which utilizes a water cooled screen to capture and remove the coarse and semi-fused particles. At this stage; the gas loses a portion of its heat with temperature falling below 608°C which is a necessary condition to avoid damage to the pipes, ducts and other metallic structure of the gas handling system. The gas is further cooled at the Radiation Cooler to a temperature ranging between 315 and 380°C. The gas is conditioned to avoid damage to the electrostatic precipitators that are designed to clean the gas by removing significant amount of dusts from the: gas stream. This gas stream is currently discharged to the stack, however, it will be treated in a sulfuric acid plant that is currently under construction and is scheduled for commissioning during the second half of 1999. The gas handing and cleaning system has been operated without any significant interruptions. Minimal emissions of SO2 and dusts in the work place are noted. The system requires minimum maintenance. The key to the high availability of the system is due to the good, performance of he Radiation Cooler, which efficiently cools the gas before entering the electrostatic precipitators (ESPs). This enables the ESPs to remove the dusts efficiently.

Jan 1, 1999

By Akira Yazawa

The composition of ferrous calcium silicate slag is located on the tie line between FeOx and calcium silicates in ternary FeOx-SiO2-CaO system. This slag has never been used as copper smelting slag because of high sulfidic copper solubility. However, when the dissolved copper in slag is just oxidic, as in direct white metal production or in converting process, this slag is quite attractive and can be regarded as the third copper smelting slag after fayalite and calcium ferrite slags. Based on the authors&apos; studies on phase separation thermodynamics and laboratory experiments, it was clarified that the oxidic copper loss in this ferrous calcium silicate slag become the minimum not only %Cu in slag but also the total copper loss when the amount of slag is taken into account. It has been proven that calcium ferrite slag is suitable for continuous converting where the dissolved copper is oxidic, but there exist some drawbacks such as limited solubility of silica, low lead removability and too high fluidity. To overcome these difficulties accompanying traditional slags, ferrous calcium silicate slag is the hopeful alternative. In view of the general trends of modem copper smelting processes, the interesting features of this new slag system are discussed.

Jan 1, 1999

By Rachel De Lucas

In recent years, as the price of oil soars upward, scientists have started to focus on other energy sources, such as hydrogen. As magnesium can be used for hydrogen storage by forming MgH2, industry will see a growing demand for the hydride. In hydrogen storage and release cycles using magnesium, hydrogen is released from magnesium hydride through hydrolysis and magnesium hydroxide is produced. Therefore, recycling magnesium hydroxide back to magnesium becomes important. The solid oxide membrane (SOM) process is an emerging technology for this process. In the SOM process, MgF2-CaF2-MgO flux is contained in a stainless steel crucible, which works as the cathode. An ionic-conducting YSZ membrane, connected to a liquid metal anode, is partially immersed in the flux. During electrolysis, when the voltage between anode and cathode is higher than the dissociation potential of magnesium oxide, magnesium ions move toward the cathode and are reduced into magnesium vapor. The oxygen ions move toward the anode, passing through the YSZ membrane. They are then oxidized, forming pure oxygen, CO/CO2 or steam (by reaction with hydrogen). The magnesium vapor, generated at the cathode, is collected in the condenser as high purity magnesium. SOM experiments have been conducted with different liquid metal anodes and without reductants. The SOM technique is a highly energy efficient process and with by-products being oxygen or steam, it is also an environmentally friendly green process. A 2-D electrostatics mathematical model was developed as an initial step towards optimizing the design for a three-tube scale-up SOM electrolysis cell. Several possible geometries were examined to develop the scale-up model and convergence of the model was achieved.

Jan 1, 2006

By Dan Wang, Qian Li, Yong-bin Yang, Tao Jiang

"Thiosulfate is one of the most promising non-cyanide lixiviants for gold leaching. However, the undesirable reaction between thiosulfate and copper (II) gives rise to increased reagent consumption, which results in high cost and huge limit to its development. This paper presents study on the effect of ammonia, copper (II) and Cu(NH3)l+ ions on the oxidative decomposition of thioulfate. It shows that the presence of copper (II) and Cu(NH3)l+ can significantly increase the thiosulfate oxidation, while ammonia is relatively unaffected. The oxidation of thiosulfate by copper(II) in the absence of ammonia is fast at first and then decreases as time increased within a certain time, which can postulate that an intermediate product is responsible for the decreased consumption. The effect of ammonia is depended on the interaction with copper (II), which was found to significantly affect the consumption of thiosulfate.IntroductionFor over one century cyanidation is widely used in industrial production of gold, due to its simplity of process and low cost of production. However, cyanide is a highly toxic chemical reagent used dangerously and brings serious environmental pollution. What's more, cyanidation has slow speed of leaching gold and poorly leaching effective for refractory ores. With the exhausting of free-milling gold ores and promoted environmental protection requests, the disadvantage of cyanidation becomes a growing problem. In recent years, more and more research activities have been focused on alternative processes using non-cyanide lixiviants. Among the non-cyanide lixiviants, thiosulfate is considered as the most promising one[l-5].Compared to cyanide, thiosulfate is an inexpensive, nontoxic and less-pollution reagent, which can form complexes with many metal ions. Thiosulfate leaching of gold has an acceptable leaching rate and is insensitivity to impurities. Moreover it presents advantage on the treatment of refractory gold ores such as carbonaceous gold ores, copper gold ores, complex arsenic and sulfur gold ores, and so on[6]."

Jan 1, 2013

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By P. Louis

Gécamines is the world largest cobalt producer with about 60 % of the Western World production. During the last ten years, its annual production varied from 5,400 to 14,600 t/year. The actual cobalt production capacity of Gécarnines is 18,000 t/year and could be increased in the near future if necessary. Cobalt is presently produced at the Shituru plant by an old in-pulp electrolysis process and in Luilu, by electrolysis of a clear weakly acidic solution. The Shituru Cobalt quality is lower than the Luilu one. For that reason, part of the Shituru Cobalt is fire refined and cast into granules. Large efforts have been succesfully accomplished to improve the cobalt quality. This has been made possible by a better knowledge of the purification processes and of the electrolysis parameters.

Jan 1, 1988

By Song Ning

The main mineral constituents of phase-transformed chalcopyrite are CuS and FeS2. CuS is more soluble than FeS2 in an acidic CuCl2 solution with presence of excessive NaCl, so that FeS2 could be removed as solid residue from a leached solution. The experimental results showed that the efficiency of the copper leaching is heavily determined by the following two factors: a) The degree of the chalcopyrite phase transformation to CuS and FeS2 b)The concentration of Cl during the leaching, specifically whether there is enough excessive Cl existed. I t was found that when the Cl in the solution is not excessive, the slowest step of the leaching is the dissolution of Cu2Cl2.

Jan 1, 2006

By René Bustamante

A GPSS/H simulation is beeing done for a traditional smelter of copper, which envolves a reberberatory furnace, a set of Peirce Smith converters (PSC) and a refining furnace. The objective is to try different plant layouts, being the handling of liquid material at high temperature one the mainly concern, this envolves a study of the ladles and cranes used. Some of the modifications that can be evaluated through the model is the role of oxygen potential when tonnage oxygen is used, number of cranes, PSCs in operation, etc.

Jan 1, 1992

By D. Nozadze

A new method of isothermal electro-contact diffusion welding of layered composites under pressure is offered. The scheme is developed and laboratory installation is created on which preproduction models of the layered composite of steel and aluminum is produced. A new method of electro-contact hot deformation is proposed for realization of diffusion welding by pressure of stratified blanks providing high-temperature isothermal process. In this case a rolling process or composite pressing is meshed with simultaneous electric current transmission in deformation center. Considering that a resistance of transient layer far exceeds the resistances of composite components, the heat release takes place intensively just in this layer. As the surfaces are approached over a distance of inter-atomic forces, the energy of boundary atoms easily reaches the energy threshold of capture with a formation of qualitatively new metallic bond. Proposed method, providing isothermal process in deformation center, excludes a necessity of previous preparation and prevention of surfaces. In this case strength of layer connection may approximate or exceed strength limit of cladding layer.

Jan 1, 2006