Search Documents

By Ali S. Al-Watban

"In this paper, the room temperature friction and deformation properties of various polycrystalline diamonds; i.e. aggregates of diamond crystals with a ""binder"" phase of cobalt and a polycrystalline coating produced by a chemical vapour deposition processes (CVD) were studied when softer metallic and ceramic sliders were used. The experiments were conducted· at relatively low sliding speeds (10 mm/min), in a vacuum of 10-5 mbr after having cleaned the specimen surfaces by out-gassing them for about 30 min at 800 °C. As a result of increasing the number of traversals significant wear of the coated diamond by softer metallic sliders (aluminium and mild steel) was observed. With ceramic sliders, it is shown that the multiple traversals result in the formation of wear groove. With diamond silicon carbide, high friction and adhesion lead to significant metal transfer which then pre-empts cumulative deformation of the harder materials. With the diamond-cobalt composite, the friction is surprisingly low, there accumulation of wear debris on the tip of the slider but no permanent transfer of metal and the harder specimen is not damaged even after 5000 traversal.IntroductionPolycrystalline diamond is mainly produced as tool materials for the machining of hard metals and composites. Thus, the sliding friction and wear resistance are amongst the most important properties relevant to those applications.During cutting by PCD the wear mechanism is mostly influenced by the chemical affinity between the tool material and the workpiece. For example, diamond based materials are not recommended for machining ferrous materials because carbon is highly solubie in iron: This leads to the graphitisation of diamond particles and hence a high rate of diffusion wear is observed (Brookes and Lambert, 1982)."

Jan 1, 2000

By H. Itou, J. M. Toguri, T. Takasu

"Marangoni convection has a large effect on materials processing since it remarkably enhances heat and mass transport near a free interface. To have a better understanding of the behavior of Marangoni convection in molten salts, observation and calculation of the thermal convection in a column held between a pair of Pt disks (2mm in diameter) fixed to hot thermocouples, were carried out.Calculated flow patterns and absolute values of fluid velocity agreed well with the observed results. When the temperatures of both disks were set equal and the height of liquid column was 2.4mm, four vortexes were generated on the longitudinal plane with a typical velocity of 15mm/s . From the calculated isothermal lines, the behavior of the enhanced heat transport was obvious; fluid heated at the disks was conveyed to the free surface and the cooled fluid at the surface was conveyed to the inner region. Increase in the height of column and/or increase in the absolute value of applied temperature difference lead to increase in fluid velocity lineally in this calculation range.IntroductionIn the processing of many materials, fluid flow of melts has a large effect on refining capabilities and on the characteristics of the produced material. Marangoni convection is generated when a spatial gradient of interfacial tension exists on the free interface due to differences in temperature and/or concentration. This promotes heat and mass transfer locally near the interface.For example, Marangoni convection which are created following the dissolution of interfacially active materials, increases the local corrosion rate of refractories (1-3). In absorption and discharge of oxygen and/or nitrogen in a molten metal, the effective reaction rate of the gas components through the gas-liquid interface increases (4-7). Also in crystal growth, the distribution of defects and impurities in the crystal is affected and this can alter its quality (8-11 ). The temperature distribution is also affected and can greatly change the productivity. For these reasons, the effectiveness of Marangoni convection in refining should be quantitatively clarified and its control should be better understood."

Jan 1, 1997

By T. -M. Guo, M. J. Braun

"This paper presents an experimental and numerical study of melt flow near the solid-liquid interface and its effect on the interface curvature in a horizontal unidirectional solidification system with succinonitrile. Melt flow is introduced by increasing the ampoule channel thickness. Visualization techniques are employed to observe the flow field and the solid-liquid interface curvature. A numerical model is also developed to simulate the heat transfer, melt flow and phase change in the system. Quantitative information on the flow and temperature fields is generated. A good agreement is achieved between the experimental observations and model predictions. The results could be used for the study of the effect of the melt flow on interface morphology during solidification.IntroductionClassic unidirectional solidification experiments of transparent alloys are conducted with thin film samples sandwiched between two glass slides to investigate the development of interface morphology during solidification [1]. Samples with small channel thickness are usually used to suppress any melt flow due to natural convection and solidification in the channel would then be in the diffusive regime so that the solidification theory can be significantly simplified [2, 3]. Effects of melt flow, in particular due to natural convection, on solidification have also been studied extensively in those systems with large geometrical dimensions [4-6]. These studies indicate a strong effect of the melt flow on interface curvature during solidification [5, 6]. Only limited efforts were made to address the effect of the melt flow on interface morphology in horizontal unidirectional solidification, in particular for the cases when the channel thickness is not thin enough to suppress completely the natural convection [7]."

Jan 1, 2004

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By Jie Li, Zhongliang Tian, Xun Hu, Kai Zhang, Yanqing Lai, Hongliang Zhang

The Al-Sc Alloys show many advanced properties for a wide range of engineering applications. But the metal Sc must be added into the metal Al in the form of the Al-Sc master alloy, which is usually produced by the thermal reduction process. In this paper, the decomposition voltages of Sc2O3 and Al2O3 in Na3AlF6-K3AlF6-AlF3 melt were calculated based on the Nernst equation. And the Al-Sc master alloy was prepared in the melt at 950°C by electrolysis. The results show that the Al-Sc master alloy can be prepared by the co-deposition of Sc3+ and Al3+ at the cathode if the concentration ratio of Sc2O3 to Al2O3 in the melt is more than 2:1 under the condition of the aluminum electrolysis. SEM and ICP analysis of the product indicates that the Al-Sc master alloy is made of the phase Al and the phase Al3Sc.

Jan 1, 2016

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Yuanbo Zhang, Ruijun Wang, Qian Li, Zhao Jing, Guanghui Li, Zhengwei Yu, Chen Liu

The high content of sodium and potassium in sinter is harmful for blast furnace ironmaking. Reductive sintering technology can remove more alkali metals than conventional sintering process. In order to improve the removal ratios of Na and K, reductive sintering with both CO-containing flue gas circulation and carbon-bearing pellet was conducted in this study. Experimental results show that all indexes except the VSV and P were improved in reductive sintering with CO circulation. Flue gas circulation technique combined with carbon-bearing pellets were beneficial to reductive sintering, because it could maintain good sintering indexes and enhance the removal of Na, K. The best removal ratios of Na, K and reduction degree of iron oxides were 20.37%, 63.73% and 23.76%. In reductive finished sinter, silicate mineral becomes the important binder phase, and main iron mineral phases are wustite (FexO) and magnetite (Fe3O4).

Jan 1, 2016

By Vladimir Mindin

This paper presents results of thermodynamic investigations and experimental' studies of some essential for pyrometallurgy of sulfide concentrates topics. Among them: 1. Thermodynamic simulation and experimental investigations of roasting process, 2. Thermodynamic investigations of sulfur dioxide off-gases treatment technologies. 3. Investigations on "Mind in -Kiknadze" effect of suppression of sulfur dioxide formation during sulfide concentrates roasting in the vapor containing atmosphere. 4. Thermodynamic simulation and experimental investigations of sulfide concentrates and manganese containing materials co-roasting processes. Some essential aspects of thermodynamic simulation techniques are also discussed.

Jan 1, 1998

By Hiromichi Ohta

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thermal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thermal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By W. K. Choi

Stainless steel exposed to wet environments at ambient temperature is subject to the formation of a surface biofilm. Depending upon the prevailing environmental conditions (dissolved oxygen, pH, Eh, concentration of cationic/anionic species), the biofilm may stimulate corrosion through formation of differential aeration zones and concentration cells. Corrosion significantly impacts the United States economy, since on a yearly basis, corrosion induced losses are estimated to be over $200 billion. A large portion of this corrosion is imputable to bacterial activity, and basic information is needed for a better understanding and control of the biocorrosion phenomenon. The present study has investigated the influence of Thiobacillus ferrooxidans in the corrosion of American Iron and Steel Institute (AISI) 304, 316 and 416 stainless steel samples. The formation of biofilm and microstructural changes on the surface of stainless steel samples and their weldments were assessed by microscopic examination, and the changes in the mechanical properties by stress-strain measurements. The significance of the results will be discussed.

Jan 1, 1993

By Hiromichi Ohla

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thernnal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thennal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By Bing Gao, Zhe Wang, Xiangdong Xing, Xueqi Zhang, Shan Ren, Jianliang Zhang

"In sintering, the flame front speed (bed permeability) and sinter qualities are greatly depended on the feed size, especially coke breeze and limestone particle size. It is well known that coke breeze provides sinter bed with heat to meet the demand of partial fusion and diffusion bonding while limestone reacts with iron ore to generate bonding phase in the sintering process. Accordingly, it is necessary to find the optimum combination of different particle size of coke breeze and limestone to yield sinter associated with better qualities. In this study, sinter was produced in the sinter pot with varying coke breeze and limestone particle size together in sintering of a coarse hematite iron ore. The sintering productivity was measured and all of the result sinters were examined by microstructure analysis and reduction degradation test (RDI test). For the sintering of a coarse hematite iron ore, it was found that the optimum mean particle size combination of coke breeze and limestone was 1. 71mm and 1.55mm in the sinter mix. On such a circumstance, sintering productivity was higher and the properties of sinter were better.IntroductionNowadays, as the main iron bearing burden material of modem blast furnaces, sinter has a great influence on the blast furnace operation. Sintering is a greatly complex process involving various chemical reactions to form kinds of mineral phases [1, 2]. In the sintering process, coke breeze is used for fuel and it generates heat to raise the green bed temperature. Limestone serves as flux and it reacts with iron ore to produce various mineral phases. On one hand, during the sintering process, the particle size of coke breeze can have an effect on temperature, atmosphere, the flame front speed and all of them act on the microstructure and mineral constitutions of sinter [3, 4]."

Jan 1, 2013

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By K. J. Richards

The converting of copper mattes to blister copper has seen few technical advances since the introduction of batch furnaces using submerged tuyeres over a hundred years ago. The first side-blown converting vessel, operated by P. Manhes in 1882, was an offshoot of the 'Bessemer steelmaking process, and subsequent improvements in the conversion of molten mattes resulted In the Peirce-Smith converter, still the Industry standard today. While Peirce-Smith' converting has served the industry well since the early 1900!s, increasingly stringent environmental regulations, burgeoning energy costs, and a trend toward continuous processing have set the stage for a major improvement in this area of copper production. In contrast to a growing number of approaches for continuous converting using molten copper mattes, Kennecott is developing a process for treatment of solidified matte which allows improved' control, higher oxygen enrichment and a separation or decoupling of smelting and converting operations not possible with the other converting technologies. The new process known as Solid Matte Oxygen Converting, or SMOC, eliminates the need for molten matte transfers, minimizes fugitive emissions, and produces high strength SO2 off gases which substantially reduce offgas handling requirements. The SMOC process, despite additional matte solidification and size reduction steps, offers both capital and operating cost advantages for new smelters and the upgrading of existing plants, when compared with conventional converting technologies. Capital cost reductions of up to 35% in converting, gas handling, and sulfur fixation are indicated. Kennecott has successfully tested the new process concept and continued' development work is now under way to commercialize the technology. This paper reviews the limitations of batch copper converting with emphasis on the need for a continuous process, previous industry approaches to continuous converting of molten mattes, and the new Kennecott development.

Jan 1, 1983

By Adam Powell

A Cahn-Hilliard phase field model is formulated to describe transport-limited electrochemical reactions coupled with fluid flow in a metal reduction cell. When the reaction is limited by mass transfer of metal ions from the electrolyte to the cathode, the metal-electrolyte interface at the cathode exhibits a Mullins-Sekerka instability, leading to the growth of dendrite-like "streamers" of liquid metal into the electrolyte, which in turn significantly enhance the apparent mass transfer coefficient there. Model results for iron reduction from ferrous oxide in slag show formation of these streamers. Although the double-layer is not included in this model, the related phenomenon of electrocapillarity can be represented by a gradient penalty term which includes the electric potential gradient, such that interfacial energy is a function of the electric field normal to the interface.

Jan 1, 2003

By W. Hoffelner

Plasma technology has become increasingly important for the treatment of several types of waste (toxic, nuclear, metal-bearing scrap). Plasma furnaces combine the advantages of a closed hearth process with a very versatile (several plasma gases can be employed) and effective heat source. It can be successfully used for recovery of metals with subsequent purification and/or vitrification of residuals from drosses or filter dusts.

Jan 1, 1994

By D. Doungdeethaveeratana

The extraction kinetics in a novel solvent extraction process have been investigated. In this process, the liquid-liquid emulsion is generated by bottom gas injection into countercurrently flowing aqueous and organic phases. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration, without any mechanical moving parts, and the ease of cleaning and process control, while providing a sufficiently large interfacial area for rapid mass transfer. The overall rate increased with increasing gas injection rate and height of the aqueous phase but decreased with increasing injector diameter at the same gas injection rate. The variation of the overall rate constant was correlated against a set of dimensionless numbers, representing the operating conditions. Extraction rates and efficiencies comparable to those in a mechanically generated emulsion were attained in this new process.

Jan 1, 1998

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By José Antonio, Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo, Antonio Ernandes M. Paiva

"The production of alumina from bauxite using the Bayer process generate 1.25 ton of the residue known by red mud and 460 kg of CO2 per ton of alumina.The direct use of exhaust gases from the alumina refineries to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing the reactivity of red mud and sequester approximately 15% or 67 kg of CO2 per ton of alumina.This paper shows the reaction of a suspension of bauxite residue-water with a simulation of the calcinator exhaust gases of the refinery. The influence of the temperature and the ratio water red mud is also analyzed.2 IntroductionThe production of millions of tons per year of alumina around the world generates around 1.25 tones of the residue known as red mud and 0.4 ton of CO2 per ton of alumina . The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity is considered dangerous and currently there is no operating process capable of reuse all the material at any refinery. These lakes after filled of solid material eventually have the surface revegetated. Otherwise will need monitoring for decades and remain as an environmental passive. The search of a industrial process that combine the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of use in large scale in a economically viable way is the main objective of this work.The use of the exhaust gases of the refineries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester million of tones of CO2 plus other gases like SO2 [7] and NOx.This project main objective is to study the reaction of the CO2 with the Bayer process residue in order to obtain the basic parameters to design an equipment capable of process this reaction on a pilot scale. With this objective compositions of red mud on spray were processed with flow of gas containing CO2 at different temperatures and with concentration similar to the exhaust gases of the calcination process of the refineries. With the results, basic concepts of a pilot scale equipment were evaluated.A revision of the work already done on this type of residue were done [3, 9, 10]. Alternatives and potential barriers on chemistry and environmental fields were discussed. With the objective of industrial application the potential use of these materials were evaluated through the pH control, mass balance and x-ray diffraction."

Jan 1, 2010

By Hong Ouyang

A unified computational model has been developed for the Bridgman growth processes of B-NiAI and CdTe crystals. To handle the geometrical and physical complexities, a two-level approach has been developed. At the gtobatlevel, conjugate heat transfer, phase change dynamics, and variable material properties along with the realistic geometries and thermal boundary conditions are accounted for inside the entire crystal growth system. Refined calculations are then made within the ampoule, with the boundary conditions supplied by the global simulations. This model can optimize the use of computational source, help understand solidification behaviors, and improve designs of crystal growth system.

Jan 1, 1996