Search Documents

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Yotamu Stephen Rainford Hara, Animesh Jha

The investigation focuses on a low temperature recovery of Cu and Co from a 40 wt% SiO2-(30 wt%Fe,6 wt%Al)2O3-10wt% CaO-7wt%CuO-7wt%CoO slag over a temperature range of 1173K to 1323K. The alloy phases containing Cu-Co and Fe-Co alloy formed via the carbothermic reduction of oxides: MO + C = M + CO(g), where M represents metallic copper, cobalt or iron. In the direct reduction of oxides, the recovery of metallic phase was well below 90% at 1323K, due to the kinetic barrier which was analysed and attributed to oxygen and metal-ion transport in the slag. This barrier was overcome by adding CaSO4 and carbon, which yields a matte (MS) phase via MO + CaSO4 + 4C = MS + CaO + 4CO reaction. Lime thus produced in situ participates in metal oxide/metal sulphide reduction reactions, which are analysed with the help of X-ray powder diffraction, scanning electron microscopy, and thermogravimetric analysis.

Jan 1, 2014

By Ian M. Ritchie

Right across the universities of the developed world, the traditional disciplines of physics and chemistry are losing ground. Extractive metallurgy, which depends so heavily on chemistry, is also contracting despite a clear need for people with this kind of training in the mining industry. Reasons for this loss of popularity are discussed in this paper. High on the list is one of image. The extraction of metals is widely seen as a dirty, polluting, sunset industry which involves working in remote and uncomfortable corners of the earth for inadequate compensation. Ways in which the image problem can be overcome are considered. It is concluded that a concerted effort needs to be made by the universities and industry to redress this situation. The importance of extractive metallurgy, both now and in the future, when a greater emphasis will be placed on sustainability and recycling, needs to be stressed. In addition, courses need to incorporate training for a career path that leads on beyond extractive metallurgy.

Jan 1, 2003

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By William Petruk

"Heap leaching is a developing technology for recovering native gold and electrum from low grade deposits and from tailings. Recovery depends on permeability of the rock and ore minerals, size of particles in the heap, and ore textures that influence exposure of gold grains to cyanide solutions. These ore textures include gold-bearing veinlets and microveinlets along fractures and microfractures, gold grains in porous minerals and rocks, and gold graim. occurring along grain boundaries of other minerals. On the other hand, small encapsulated gold grains arc not likely tote exposed even with fine grinding. Most gold grains that occtir along grain boundaries of other minerals can be exposed with a moderate to fine grind, but the. resulting material will be too fine-grained to be permeable in a heap. Such finely ground ore, as well as tailings from flotation operations, can however be prepared for heap leaching by agglomerating the material into porous briquettes. Oxidized and weathered zones above. orebodies are frequently amenable to heap leaching because the gold-bearing pyrite and arsenopyrite have become permeable by conversion to porous iron oxides and ferric oxyhydroxides. A review of ore textures in several types of gold deposits suggests that:(1) the gold in vein deposits would gtmerally be amenable to heap leaching of both oxidized ores and fresh non-refractory ores,(2) the gold in Carlin-type deposits and in volcanogenic massive sulfide deposits is not likely to be amenable to heap leaching fresh ore, but oxidized zones above the orebodies are generally amenable to cyanidation, and(3) the gold in porphyry copper-gold deposits and in Witwatersrand-type deposits would likely be amenable to heap leaching of both fresh and oxidized ores but with high cyanide consumption."

Jan 1, 1997

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By Zuhair A. Munir

"The use of self-propagating combustion reactions to synthesize metallic, ceramic, and composite materials is described. The limitation of this process because of the porous nature of its products is discussed. The formation of dense bodies through the simultaneous application of pressure is shown for a metal-matrix composite. The effect of an external electric field on the synthesis of ceramic and composites is described. The nature of the effect of the field on the mechanism of synthesis is analyzed theoretically and experimentally. The use of the self-propagating combustion to synthesize intermetallic thin films is presented for the Ni-Al and Ti-Al cases. The formation of functionally gradient materials (FGM) by centrifugally-assisted self-propagating high-temperature synthesis is described.IntroductionThe use of self-propagating combustion reactions for the synthesis of a large number of simple and complex materials has been described in numerous publications. These have been amply discussed in several review articles [1-4]. The many benefits of this method of materials synthesis are commonly examined in light of its most significant limitation: the porous nature of its products. The porosity in the products of self-propagating high-temperature synthesis (SHS) is an intrinsic characteristic of the process and its elimination has been the focus of numerous attempts. Various experimental methods have been used to accomplish this goal."

Jan 1, 1994

By T. Shi, Q. Yuan, S. P. Vanka, B. G. Thomas

"The quality of continuous cast steel is greatly affected by fluid flow in the mold region, especially involving transient phenomena. Mathematical models are being applied to investigate many different aspects of these phenomena, but their accuracy must be validated before they can be applied with confidence. As part of a long-term effort to develop and apply comprehensive models of the continuous casting process, this work evaluates the relative accuracy of models of three different fluid flow phenomena in continuous casting through comparison with measurements.Firstly, transient flow simulations of velocities in the mold region are compared with digital particle image velocimetry (PIV) measurements in a single phase water model. Large-eddy simulations (LES) are found to reasonably match the flow measurements, including transient flow variations, except at long time scales, which could not be modeled owing to the excessive computation costs. The standard K-e model produced very good agreement with time-averaged velocities for relatively little computation time, although it is inaccurate at predicting the transient variations. Secondly, particle trajectory calculations are compared with water model measurements to study the distribution and flotation removal of inclusion particles. The LES model was able to match the measurements both qualitatively and quantitatively. Thirdly, steady, multi phase flow computations are compared with flow patterns observed in both a water model and an operating steel caster with argon gas injection. For the same conditions, the water model and steel caster produced very different flow behavior. The computational model was able to match the measured flow patterns in both cases.This work suggests that computational flow modeling has the potential to match real processes as well or better than water models, especially when complex related phenomena such as particle motion and multiphase flow are involved. Much work is still needed to further improve the models and to apply them in parametric studies."

Jan 1, 2001

By Liyuan Chai, Qin Liu, Bing Peng, Jia Wang, Qiang Zhang

"Electrolytic Manganese Residue (EMR) was used as the main material to prepare cementing material activator for the utilization of the residue from electrolytic manganese dioxide (EMD) or electrolytic metallic manganese (EMM) production. The effects of chemical activation, thermal activation and mechanical activation on retarding activity and excitation activity of EMR were investigated according to the setting time and activity index of EMR-slag cementing material. The results showed that the EMR exhibited good activating performance after being ball-milled for 18 min and then treated for 1-2 hours at temperature range of 350-450 ?. The optimal properties of cementing material activator were achieved at the weight percent ratio 30 : 3 : 5 of EMR/Ca(OH)2/cement clinker.IntroductionMany hazardous industrial solid wastes such as blast furnace slag, fly ash, steelmaking slag, chromic slag and electrolytic manganese residue [1] are generated n China and their amounts increases every year. The accumulation of the solid wastes during past years is very huge and they could be hardly recycled effectively as a sustainable resource. 2.35 billion tons of industrial solid wastes have been produced up to now [2]. It is estimated that they would exceed 3.3 billion tons by the end of 2015 [3]. On the other hand, the quick development of Chinese infrastructural construction needs more cementing materials. The production of traditional building materials consumes lots of natural resource such as clay and limestone and discharges at least 1 ton CO2 and other pollutants per ton clinker [4]. Therefore, it is necessary to develop new types of cementing materials instead of clinker [5,6]."

Jan 1, 2012

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By B. L. Chulu

In the carbothermic reduction of lead sulfate to produce lead, the inclusion of soda ash (Na,CO,) in the charge provides for the control of sulfur dioxide in the effluent gas. An important mechanism in the process appears to be the carbothermic reduction of the sodium carbonate whereby sodium gas and carbon monoxide are produced. These intermediates then participate in the reduction of the lead sulfate to produce lead metal and stable sulfur species in the molten slag phase. In addition, there is some evidence that the presence of lead metal in the charge may also serve to increase the lead recovery in the process. These aspects were investigated by conducting laboratory-scale smelting tests with small charges (;3g), at 1173°K(9000C). Recovery did not exceed 74w% and the role of incipient lead metal in the charge could not be clearly assessed.

Jan 1, 1993

By Richard D. Hagni

An enhanced Interest in pyrometallurgical dusts has recently emerged due to increased world-wide environmental concerns. Mineralogical study of dusts samples from lead sinter plants. lead smelters, and secondary steel mill electric arc furnaces has shown that they can be readily studied by reflected light microscopy. These dusts typically are composed of small particles sufficiently large that their mineralogical identification and characterization can be conducted under the reflecting light microscope. Scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) has been used to confirm optical identifications and chemical compositions. The sinter and blast furnace dusts at the Doe Run Smelter at Herculaneum, Missouri are commonly about 20-150 11m. They consist predominantly of galena, chalcopyrite, sinter. slag. coke. and particles. Dusts from remote sampling sites 112-1 mile from the lead smelter are composed of similar particles and abundant fine-grained particles, less than 10 um. of locally derived calcium-aluminum silicates. Electric arc furnace (EAF) dusts are mostly spherical and less than 10 11m. They consist predominantly of iron oxides (magnetite. franklinite. jacobsite and solid solutions of these spinels), zincite. and calcium-iron silicate glass, together with smaller amounts of hematite. sylvite. coke and metallic iron. Reflected light microscopy is rapid provides mineralogical data on individual grains within dust particles. and allows direct observations of textural intergrowths in pyrometallurgical dust particles.

Jan 1, 1991

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By James C. Barker

Near Rainbow Mountain in the east-central Alaska Range an ultramafic complex forms a sill-like intrusion composed of dismembered bodies exposed along the south side of the Denali Fault and Broxson Gulch Thrust. The complex comprises dunite and peridotite with lesser gabbro, which together exhibit poorly defined, steeply-dipping compositional layering. The complex hosts four types of copper-nickel occurrences which have characteristic platinum-group elements (PGE), gold, and cobalt distributions. Three of the occurrence-types are considered to have formed as a result of primary mineral segregations which developed during intrusion of the complex. The fourth type of copper-nickel occurrence formed as a result of post-magmatic hydrothermal fluids at intrusive contacts. Scanning electron microscope examination indicates that PGE occur as micron-size telluride and arsenide minerals.

Jan 1, 1987

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By Reed M. Izatt

SuperLig® materials are capable of individually separating Rh, Pd, and/or Pt in highly purified form (99.95 to 99.99%) from a variety of chloride-based feed streams in a single stage operation. The hydrophillicity and associated kinetics of the supported materials allow for operation at relatively high flow rates of both loading and elution in a packed bed format. Pilot and commercial systems have been operated with Rh, Pd, and/or Pt present in the feed from single digit ppm (mg/l) to tens of g/l. A dual SuperLig® system for one pass Au(CN)2- separation followed by Cu and CN- recovery for CN- recycle has also been tested up to a pilot level,

Jan 1, 1999

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By John A. Thorpe, Gary R. Maxwell, Kirk M. Schall, Kenneth A. Brunk

"Gold ores containing oxide and some sulfide copper minerals incur significant cost penalties when leached with cyanide, because 4-5 moles of cyanide are consumed for each mole of leached copper. This equates to ~4 kg of NaCN per kg of leached copper. Total cost of excess NaCN consumption plus CN destruction can exceed $4.00 per tonne of ore. AuGMENT Technologies has patents pending on a process that can 1) economically recover 70-80% of the cyanide that is fed to a mill, 2) produce salable copper cathodes, and 3) reduce the need for a cyanide destruction facility. Standard equipment for resin processing and electrowinning are used to recover the cyanide and produce the copper cathodes. Steps have been taken to determine: 1) how to develop the resin kinetics, 2) how much savings are incurred at a mill site, 3) how the novel 'electro-elution' circuit achieves efficient operation.IntroductionWhen gold ores containing nuisance copper are leached with cyanide, a significant cost penalty is incurred because 4-5 moles of cyanide are consumed for each mole of copper that leaches. This is equivalent to the use of -4 kg of NaCN per kg of copper that leaches. The total cost of excess NaCN consumption plus cyanide destruction can exceed $4.00 per tonne of ore.AuGMENT Technologies has a patent pending on a process that can 1) economically recover 70-80% of the cyanide that is fed to a mill, 2) produce salable copper cathodes, and 3) reduce the need for a cyanide destruction facility. This ACCS (Au-.C.u-.C.N Solution) Process Technology involves the novel application of copper cyanide chemistry. Standard resin processing and electrowinning equipment are used to recover the cyanide and produce the copper cathodes."

Jan 1, 1997