Search Documents

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

By B. Steyn

AngloGold Ashanti?s Obuasi Mine, in Ashanti Province, Ghana, operates a plant utilizing bacterial oxidation technology. The mineralization consists predominately of arsenopyrite with gold associated in the sulphides. The plant was commissioned in 1994, at that time was the largest BIOX® plant in the world, and has been operated by AngloGold Ashanti since 2004. The constraints identified in the plantwere the flotation capacity, BIOX® feed size and disruptions to the BIOX® process. This paper focuses on the practical steps that were followed in order to increase the recovery of the plant. The original plant design was based on a head grade of 10 g/t and an overall recovery of 86.5%. In 2007 the plant was operating at an overall recovery of 79.2% at a head grade of 5.6 g/t and this has improved to 80.6% at a head grade of 5.8 g/t during the last quarter of 2008. Additional improvement to 81.5% are expected by the end of April 2009. Improvements that have been implemented include: ?Replacement of the regrind mill ?Installation of additional float capacity ?Installation of a scavenging circuit ?Installation of a complete water treatment plant. In addition we have focused on the effect of the water circuit on the BIOX® process and the steps involved in correcting this problem. The water circuit was originally designed as an open circuit and through environmental considerations the circuit was closed towards the end of 2007. The bacteria in the BIOX® are particularly sensitive to cyanide and cannot tolerate levels above 0.05ppm (free cyanide), this required extensive modifications to the water circuit. The plant improvement project is ongoing and the current scope of work should be complete by the end of April 2009. Further research and development work is being planned, which includes a ?white rot bacteria? that can consume the preg-robbing carbon and oxidize the sulphide in a single pass.

Jan 1, 2009

By Alastair Grogan, Ron Elliott, Dale MacLean

Blasting for armour stone presents many unique challenges. Often, blasters get themselves into trouble when they assume that they can simply modify a production blast design to produce the required fragmentation size. They bid on the project using typical production blasting costs, and then find that they cannot produce the required fragmentation size and quantity with an acceptable waste factor. This paper outlines industry best practice guidelines for the production of riprap or armour stone. The paper examines the importance of initial geological mapping to determine the average in-situ block size, and the advantages to be gained from working with the geology to maximize production of the required block sizes. The paper also outlines the importance of proper explosives selection as well as blast designs that are unique to the production of riprap. The paper reviews challenges and experiences realized from multiple projects in differing rock types.

By R. Gehauf

Magnetic separation using rare earth rolls (RER) and rare earth drums (RED) have seem tremendous development and use in recent years. While the process of magnetic separation is understood, the principles affecting the separation, the specific application and the optimization of RERs and REDs are less well known. This paper offers practical insight into the basic operation, selection and optimization of RERs and REDs. It is a guide for the engineer who must design a test series and select the proper equipment for that application. It provides the engineers and line operators who control the daily operation of the equipment a basic understanding of the dynamics of operation and the principles that govern the optimization of RERs and REDs.

Jan 1, 2004

Dealing with Aboriginals and various others purporting to represent them has become part and parcel of exploration and mining in Australia, whereas 20 years ago it was not. The author has been involved in dealings with Aboriginal groups over this period. The following paper is a summary of the social background to such dealings and a compendium of rules for the newcomer to this aspect of the resource industry.

Jan 1, 1990

By B W. Atkinson, J Docherty

An Australian Working Group has been compiling a guide for operators to use in order to improve the efficacy of their routine and non-routine sampling tasks within their coal preparation process. The guide focuses on unit operations within the process, and not conveyor belts or transfer stations that are adequately covered by the existing Standard ISO 13909.Representative sampling of unit operations is generally an after-thought following plant construction, whether that be a result of oversight, or more commonly, capital cost minimisation during initial construction. Minimising capital cost by avoiding adequate sampling systems is generally a poor decision, since the result is a process that cannot be adequately measured, meaning that it cannot be adequately managed and optimised.The use of the term ‘guide’ rather than ‘standard’ is intentional. Practical means of sampling unit operations within existing plants generally relies on a compromise between sample representativity (minimisation of bias) and sampling feasibility. The guide does not endorse poor sampling practice, but instead offers practical guidance to overcome, to the extent reasonably possible, real-life limitations.When it comes to sampling any particular process, it is almost always necessary to make a professional judgement as to whether or not the proposed samples are likely to be sufficiently representative such that the sampling will be worthwhile. Such judgement needs to be exercised by personnel who understand the principles of sampling, as they apply to the stream being sampled. There are many circumstances where available methods for sampling of a particular stream will be meaningless, and in such circumstances analytical data from that sampling will only serve to propagate poor decision-making.This paper outlines the approach for the guide, the areas it covers and the approaches adopted for different types of unit operations and associated equipment configurations.CITATION:Atkinson, B W and Docherty, J, 2017. A practical guide to sampling in coal preparation plants, in Proceedings Eighth World Conference on Sampling and Blending , pp 241–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

Response of a mineral to anionic and cationic flotation reagentsvaries with the nature of the mineral and the particle size. A ruleis deduced for the selection of the correct type of reagent, which leads to a simple method of testing ores to determine the possibility of separating the constituents by flotation.

Jan 1, 1963

By M S. Stern, R Aguila

To control direct blasting costs many open pit mines dewater and line wet blastholes before loading them with ANFO or Heavy ANFO blends of explosives. The plastic lay-flat tubing used for these liners can be punctured during loading and allow water to partly dissolve and desensitise the explosive column which reduces blasting performance.

Jan 1, 1997

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By J. B. Yianatos

A practical an interactive model to describe the operation of a flotation bank of mechanical cells was developed based on the hydrodynamic and metallurgical characterization of large industrial flotation cells. Thus, the mineral grade and recovery, as well as the stream properties along the flotation bank can be described in terms of the operating variables. The model was built considering the flotation bank as a distributed system, so the solution for the water and solids mass balances, per size classes, for each single cell, are sequentially solved. Also, each cell was described by two distinct zones, the collection zone characterized by the flotation rate constant and the froth zone characterized by the froth recovery. The mineral feed was described in terms of the mineral species and particle size classes, using a rectangular flotation rate constant distribution. Also, the effect of changing the actual operating variables (air flowrate, pulp level, pulp density, pulp flowrate, etc.) on the mineral collection process, in the collection (pulp) zone, was considered downstream along the bank. The froth recovery of floatable mineral has been estimated by measuring the mass flowrate of particles entering the froth by true flotation together with the concentrate mass flowrate (ton/h). The mass flowrate of collected particles at the pulp/froth interface level was calculated from direct measurement of bubble load (ton/m3) and gas flowrate (m3/h). Flotation recovery is mainly related to the froth depth and air flowrate. All parameters considered in the model have been adjusted from direct measurements in plant site. Also, the effects of other operating variables such as reagents dosage, top of froth grade, or froth discharge velocity are presently under study. This procedure has been tested using data from industrial rougher operations consisting of flotation banks with 5 cells to 9 cells in series, and different cell sizes, such as 45m3, 130m3, 160m3 and 250m3. Thus, it has been shown that the model approach is a powerful tool for flotation cells diagnosis, operation and development of new control strategies, as well as, to evaluate the effect that de-sign and operating variables have upon the collection and froth zones performance in large flotation cells.

Jan 1, 2014

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

By Herbert H. Kellogg

A model of the ISF is described. which reproduces with accuracy the "normal" operation of three industrial furnaces. The model, written in Fortran, is based on detailed heat and material balances, and the concept that the ascending gases reach equilibrium with zinc oxide and with the water-gas shift reaction. "Solution loss" of carbon in the lower shaft, and partial reoxidation of zinc vapor in the upper shaft are also essential features. For prediction of furnace behavior under altered operating conditions (blast rate, temperature, moisture content, oxygen enrichment, or injection of oil or coal through the tuyeres) the model modifies the heat loss, temperature of slag and bullion, amount of reoxidation in the upper shaft and the condenser efficiency to reflect the altered operating parameters. Model predictions for such operating conditions are in reasonable agreement with plant experience.

Jan 1, 1990

By D. Farahmand

This paper focuses on formulating a practical procedure for forming long-range production and development schedules in underground mining. A computer program developed to be run on a microcomputer is presented and discussed in detail, and a practical case study is analyzed to demonstrate the suitability of the procedures discussed in the paper. The intent of the computer scheduling model is to have quick access to vital information when changes in development and production are under consideration by management.

Jan 1, 1986

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By Osborn G

The bulk flotation behaviour of an industrial rougher bank has been determined with a view to characterising the size iepend ent behaviour of the identifiable nineral groups present. A relatively simple flotation model, based on first order kinetics and the assumption of perfect mixers in series ias been used to provide a fit to the operation of the cells. The adequacy of the model is discussed in relation to the characteristics of the ore and the size iependancy of the parameters. It is shown that improved fits are possible if the model accounts explicitly for this size dependancy and demonstrated how the model may be of use in prediction of the grade recovery relationships for different operating conditions as an aid to plant optimisation.

Jan 1, 1986

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007