Search Documents

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011

This paper carries on from an earlier paper 'Cemented fill practice and research at Mount Isa' and reports further on the laboratory programme at Mount Isa to develop a cheap cem- ented fill using Company waste products. The practical economic significance of availability of cheap cementing agents is re- viewed, with the various alternative approaches available The basic approach adopted within this paper is that use of reactive pozzolans such as ground slags to replace a proportion of the Portland cement in the fill can make mining methods employing cemented fill more economic- ally competitive with other mining methods.

Jan 1, 1973

By Edmund W. Murphy

At the first workshop on Surface Subsidence Due to Underground Mining (1 981 ) , Yarbrough delivered a paper (1 ) describing the mine subsidence insurance program in Illinois operated as the Illinois Mine Subsidence Insurance Fund (IMSIF) . In this paper we will present claims data and describe changes that have occurred in the Illinois Insurance Code during the first six years the IMSIF has been in existence. The change in the original Illinois Public Act 80-1 41 3 that most affected the public was an amendment increasing the maximum amount of mine subsidence insurance avail- able on a structure from $50,000 to $100,000. Seventy-two counties in Illinois have been undermined for minerals, primarily bituminous coal. In Franklin County (.in the southern part of the state) 36 percent of the land area has been undermined for coal extraction. In St. Clair and Madison Counties , two counties that include the St. Louis Metropolitan area along the western border of the state, 10 percent and 7 percent of the land surface have been undermined. Most of the undermined area in the two counties is beneath urbanized land. In 34 counties, approximately 1 percent or more of the land surface has been undermined (2). The first shaft mine in Illinois was sunk in the city of Belleville (east of St. Louis) in 1842, and the mines of early vintage have initiated the majority of the mine subsidence claims. Data compiled from the first six years reveals that most Illinois mine subsidence events that affect structures occur over abandoned mines where early methods of high- extraction mining practices were used. Maps of these mines operated in the 1800s reveal irregular development of room and pillar areas and poorly defined production areas (panels). Rooms in the mines varied from 15 to 40 feet in width and the pillars varied in width from 5 to 40 feet. The pillars were often long and narrow. Recovery rates in mines that operated prior to 1900 generally averaged 50 per- cent, and extraction rates as high as 80 percent have been documented (2). Some pillar robbing occurred.

Jan 1, 1986

The incidence of colliery disasters has highlighted the need for more centralised and directed coal mining safety research in Queensland, with particular impetus from explosions at Box Flat in 1972, Kianga in 1975 and Moura No 4 in 1986. Inquiries which identified the likely causes recommended measures and, research and two outcomes have been the present Mines Safety Research Advisory Committee and The Safety in Mines Testing and Research Station at Redbank, near Brisbane, dealing with all mining problems, coal and metalliferous. Already, important research into ignition and explosion and other health and safety matters has been accomplished; the Station has become an accredited testing laboratory; and international recognition has been achieved. Now the advisory, testing and research arms are soundly in place to pursue preventive investigations and be ready to provide assistance in any emergencies.

Jan 1, 1991

By T. Takamori

This paper reviews the present status of coal preparation in Japan concentrating on the process in coal cleaning and waste water treatment. This paper also discusses recent topics on maintenance, automatic control, raw coal management, etc.

Jan 1, 1982

By Harry Perry

Although the markets for coal in the United States have changed rapidly over the last three decades, the uses of coal, namely, to produce heat and power or coke have been left almost unchanged. The coke is used either as a chemical reducing agent alone or as a reducing agent and source of heat. Most of the heat and power markets for coal require no coal processing, although for more than 50 years, many proposals to skim the more valuable substances in coal before burning have been advanced. Thus, the only large tonnage market requiring processing of coal is high-temperature carbonization to make coke. At present, coal requires processing for some small markets, but for future potential large markets, such as gasification, conversion to liquid and gaseous fuels, and conversion to chemicals, coals will require more processing than is now being done.

Jan 1, 1962

By Joseph C. Hirschi

Mine engineers have been interested in building models that simulate mining operations since computers were introduced to the industry in the 1960s. Computer models enable operational scenarios to be evaluated without the need for actual field experimentation. Virginia Tech’s FACESIM and CONSIM, Penn State’s UGMHS, and KETRON’s CPMINE are perhaps the best known early models. Recently, SIUC has modified a Microsoft® Excel version of Virginia Tech’s Mathematical Model, calling it the SSP Model. It is used to quantify the significance of various controllable parameters. Productivity increases approaching twenty percent may be achieved where recommendations suggested by the model are applied.

Jan 1, 2005

By J. W. Oberholzer

The use of computers in the South African coal mining industry has increased during the 1980s. Applications at mine level commenced in the financial and personnel areas of payroll systems, mine accounting procedures and staff record keeping. More use is made now on mines of technical programs for purposes such as mine planning and mine survey calculations. The Coal Mining Laboratory of the Chamber of Mines Research Organization has provided, for a number of years, a service to Chamber member collieries in regard to the application of technical computer programs. Programs presently in use for simulating production procedures and conveyor belt transport systems are described. In addition, reference is made to the collection, storage and analysis of data concerning the performance of continuous miners over a period of eight years. More recently a computer program for the simulation of the cutting action of continuous miner cutting drums has been developed. The use of this program to assist with drum design is explained. The fact that many requests to make use of the programs are received from collieries is an indication of their acceptance by industry. Their interest in running the programs themselves on their own desktop computers has led to the need to convert the software for microcomputers.

Jan 1, 1987

By David La Rosa, Matthew Craft, Lee Julian

Rules of thumb are ubiquitous in blasting. Typically presented as ratios, they assist with the initial assumptions of blast design and provide guidance for best practice. Examples include the blast hole diameter as a function of bench height, and stemming length as a function of hole diameter. The most common rules of thumb were developed in mid-20th century and it is important for a blaster to know if the rules of thumb are still reliable.

Feb 6, 2023

By J. A. Allan

"The history of the development and application of controlled recirculation systems in U.K. collieries is traced and the theory behind such systems briefly examined. Specific applications for dealing with dust and dust/heat problems in headings, for which practical experience is currently available, are described. Consideration is given to the special features which these systems introduce in the underground situation and to the essential safeguards which are required for their safe use.IntroductionRecirculation of air is a commonly used technique in genera l ventilation and air conditioning practice, but has always been regarded with some suspicion for mining applications. This is perfectly understandable in view o f the hazardous conditions which can occur with dangerous forms of recirculation in mines. However, certain controlled recirculation techniques can offer advantages, particularly in the field s of dust and climate control in headings, provided that they are designed, Installed an d managed with full comprehension o f all aspects of the system and always bearing in mind that from the point of view of serious firedamp ignition risk, headings are potentially the most hazardous places in coal mines.BackgroundProbably the first recorded use of deliberate recirculation in British collieries was reported by Lawton in 1933. This researcher described trials, undertaken under the auspices of a national committee on ""The Control of Atmospheric Conditions in Hot and Deep Mines"", involving attempts to increase the velocity, and thereby the cooling power on hot faces, by means of simple recirculation systems using fans and ducts delivering recirculated air in the opposite direction to the normal face airflow. No significant cooling advantage was obtained and there is no subsequent record of this work being continued. During the discussion on this paper, there was considerable disbelief that fire damp percentages had not increased significantly when air was recirculated, but apparently no attempt was made to establish why this should be. It is of interest to note that J. Ivon Graham, one of the contributors, recommended that recirculation should be tried in stone headings for the control o f dust, as he believed that ""there may be scope for recirculation and filtration of the air under certain circumstances in such headings"". This idea was not developed for another forty years."

Jan 1, 1983

By Kristian E. Waters, Hao Ma, Haibei Wang

Heavy metal ions exist in waste effluents including mining tailings, manufacturing discharges, and smelting and metal plating process wastes. Various methods are available to treat industrial effluents containing high levels of metal ions, but when confronted with wastewater that has low metal ion concentration below 500 mg/L, most techniques suffer from low removal or separation efficiency as well as high operating cost. ELM-based techniques can be used to solve these problems.

Apr 1, 2023

By Michael S. Moats, Shijie Wang, Timothy Robinson

In 1987, John Schloen published a survey and analysis of copper electrorefining tank room data. Following this paper, a series of copper electrorefining surveys have been conducted and presented at each of the Copper-Cobre meetings over the past 20+ years (1991, 1995, 1999, 2003, 2007, 2010 and 2013). For each of these surveys, William Davenport has been key driving force in the collection and analysis of data. To honour Professor Davenport’s contribution to copper processing, a review of the data was conducted. Historic trends and possible future technologies are discussed.

Jan 1, 2014

By J. C. Paynter

A review of copper hydrometallurgy by J. C. PAYNTER, B.Sc. (Chem. Eng.) (Visitor) Copper hydrometallurgy is discussed with special reference to the treatment of chalcopyrite concentrates under South African conditions. The following processes are described and illustrated: Sherritt Gordon's ammonia pressure leachilng, the Arbiter Process, sulphuric acid pressure leaching, roasting processes, the Cymet Process, and the ferric chloride process developed at the National Institute for Metallursy. These processes are then compared with respect to the form of sulphur produced (elemental sulphur or sulphate), the character of the iron product and the handling of different types of ore.

Jan 11, 1973

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004

By H. J. Hartjens

"With the trend towards bringing into production ore bodies of lower and lower copper content every possible avenue of approach to achieve maximum copper metal recovery and keep milling costs to a minimum are of increasing importance.Equipment manufacturers have contributed a great deal by designing larger mills, flotation machines, pumps, etc. in lowering capital and operating costs; instrumentation and automation usually as a joint effort of operating staffs and equipment manufacturers have resulted in lower operating costs and improved metallurgy. Likewise manufacturers of chemicals used in mineral beneficiation have directed their research and development at new flotation reagents and treatment schemes to complement the needs for more efficient products, permitting coarser grinds without detriment to recovery, higher flotation rates, higher degrees of selectivity, as well as chemicals to improve settling, clarification and filtration. The various treatment schemes in use and suggested for consideration are:1) The choice of the flotation treatment scheme is largely dictated by the desire to operate a simple circuit, originally consisting of rougher and scavenger flotation, with scavenger concentrate either returning to the head of the rougher circuit or joining the rougher concentrate for cleaning by reflotation, with and without prior regrinding. The cleaner tailing was also recycled to the head of the rougher circuit. In the case of porphyry copper ores, this was originally the standard circuit. Lime is the preferred alkalinity regulator to adjust pH, usually in the range 10-12.To avoid the undesirable effects of circulating loads and gain the advantage of simplified control of the rougher circuit, open circuit cleaning is practiced more and more. In this scheme, cleaner tailing is scavenged to produce a discardable tailing and the scavenger concentrate returned either to the cleaner or the regrind circuit."

Jan 1, 1970

By James Keenan

Mesabi Range blasting has evolved in over a century of mining. The obstacles including: hard and heavily jointed rock, bitter winters and frequent wet holes; combine to create a unique challenge for blasters. This paper documents current pattern designs, powder selection and loading practices for these seven mines that consumes as much as 130 million lbs of explosives each year. Blasting is characterized by wide burdens and spacings, large diameter holes (up to 16-inch) and bulk loading of augered and pumped emulsion/prill products.

Jan 1, 1996

By Seymour K. M, Sampson D. B, Walker I. W

Ashton Mining Limited is the operator of two wholly-owned gold mine/mill complexes at Laverton and Leonora. In addition, Ashton owns 43% of the Bardoc Joint Venture mine/mill complex, which is operated by Aberfoyle Pty Limited. All three of these operations are located in the Eastern Goldfields region of Western Australia (Figure 1). At Laverton, milling capacity is in the order of 1 million tonnes per year in 3 mills (Duketon 200,000 tpa, Cork Tree Well 650,000 tpa and Craiggiemore 150,000 tpa). These mills service a distance of 80 km, from Baneygo in the north to Craiggiemore in the south. Mineral tenements cover a 150 km long stretch of a series of sub-parallel mineralised structures. At Leonora, the Harbour Lights mill is designed to treat 750,000 tpa of sulphide ore, and has treated oxide ores at an annualised rate of over 1 million tonnes/year. The mill is supported by several tenement blocks that lie within a 50 km trucking radius of the mill. The most important of these is the Mertondale tenement block, which covers approximately 25km of the Mertondale Shear Zone.

Jan 1, 1991

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By G. W. Ford, S. E. Black

Current research into coal based synthetic fuels is taking place on two fronts, fuels for power generation and conversion of coal to ultra-clean fuels for transportation. Present research into solid synthetic fuels is concentrated on development of clean coal technology which will meet or exceed the proposed cap and trade emissions set forth in the Clean Air Act Amendments of 1990. Research into ultra-clean liquid fuels is concentrated on either direct or indirect liquefaction process which could be used to manufacture both diesel fuels and gasoline.

Jan 1, 2003