Search Documents

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By Frank H. Kingdon

and eventually we would have trouble. That is, these little localized overstresses may not be important if the structure is loaded a few times, but may be important if the structure is loaded many thousands of times. The existence of localized stress has been demonstrated by direct experimentation with delicate extensometers by the elaborate investigations of Coker. Localized stresses four, five, and six times those that we would get by the ordinary laws of mechanics exist in most of our structures. These stresses, ordinarily, under steady load do no damage but if they are repeated many times may start progressive failure. So far, we have seen no failure that could not be explained by localized high stress at a nick, a crack, a point where one heat treatment stopped and another began, or where there was local faulting, or any one of a dozen causes. In the case of drill rods, the actual distribution of stress must be different from that which any mathematical analysis could predict. It would seem that the spread of damage from the localized overstresses, so far as we can see now, explains the phenomenon known as fatigue. The Ideal Drill Steel By Frank H. Kingdon The essential qualities of a drill steel are: (I), It must be easily forged; (2), the forged bit end must permit easy heat treatment to obtain hardness to resist chipping; (3)) the bar or body must be stiff to resist bending or twisting and yet tough to resist shock and vibration, with resulting breakage, (4), the forged shank end must be easily heat treated to obtain hardness with great toughness. Minor requirements are that the bit and the shank are in alignment with the body; that the shank is of the proper shape and length and the shank collar or lugs of the proper diameter and length; that the hole is free from obstruction; that the striking end of the shank is flat and square; that the bit is of the proper shape, with the cutting and reaming edges formed full and to the required size; that the reaming edges are concentric with the axis of the steel, and that there are no sharp corners at the shoulder where the bit blends into the body. The essential qualities of a bit, are: That its shape be such that maximum cutting speed can be maintained for as great a distance as possible before wear of the gage and cutting edge reduces the speed of penetration to a point where a change of steel is made necessary; that the size or diameter of the drill hole corresponding to the gage of the bit can be maintained with the least possible reduction as the depth of the hole increases, and that the bit can be correctly and readily formed and heat treated. The following features of bit design require attention: Shape,

Jan 1, 1922

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935

On the following pages are abstracts of papers published by the Institute during the year 1936 as TECHNICAL PUBLICATIONS and CONTRIBUTIONS, papers in bound volumes appearing for the first time, and papers in MINING AND METALLURGY For abstracts of papers that appeared in bound volumes in 1936 but that were published as TECHNICAL PUBLICATIONS in 1935, see the YEAR BOOK dated January 1936.

Jan 1, 1937

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920

By C. P. Summerhayes, J. W. G. Gilbey, S. Henley, G. P. Glasby, J. J. T. Harvey, J. Larsson, O. Akiman, A. G. Brown

Abstracts are presented from six University of London, one University of Nottingham and one University of Durham PhD theses

Dec 1, 1971

By P. G. Vikre

Several factors have caused less emphasis to be placed on geologic mapping in mineral exploration in the last 15 years. These include opportunities for "easy" discoveries of near surface gold and silver deposits in developed countries, and of base metal deposits as well in less developed countries, a decline of emphasis on geologic mapping in many universities, and a decline of useful mapping by government agencies in many areas. Geologic mapping is simply a way of recording geologic observations on volumes of rock larger than can be seen from one place. Since most geologic processes involve systems larger than this, mapping is also essential to understand the significance of observations made on smaller volumes of rock, such as thin sections and sample taken for chemical or isotopic analysis. To be useful, the observations recorded through geologic mapping are then interpreted to arrive at an understanding of the 3D geometry and geologic history of a volume of rock, which is used to direct mineral exploration, or any number of other purposes.

Jan 1, 1995

By David B. Plumeau

The Cayuga Mine, a deep rock salt mining, operation, changed from a standard room and pillar mine design to a yielding pillar/pressure arch design five years ago. In general the roof conditions improved. However, entries adjacent to the abutment pillars continued to fail. It was noticed that where abutment pillars were accidentally "notched" (by driving cross- cuts one cut into the pillars), the abutment entries had better roof conditions than where there were no "notches". Experiments with intentionally notched abutment pillars showed that notching did improve abutment entry conditions. During the past four years notch configuration has been varied to suit local ground conditions. Recently, "pre-cutting" of notches has proven itself as a means of protecting abutment entries under severe ground conditions. As an added bonus, the notches improve productivity by providing more places to work and reduce costs because it is not necessary to bolt the notches.

Jan 1, 1981

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By Md Sazzadur Rahman

Electrochemical Impedance Spectroscopy studies were conducted on two organic thermal energy storage materials; Neopentylglycol (NPG) and 2-Amino-2-Methyl-1,3-Propanediol (AMPL). The ionic conductivities and dielectric relaxation times in the low temperature ordered a-phase (monoclinic for both NPG and AMPL) as well as high temperature orientationally disordered cubic y-phase are reported.

Jan 1, 2006

By S. A. Matthews, M. L. Nave

AC variable frequency motor drives are emerging technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of drive, motor, and conveyor features. The purpose of this paper is to familiarize and inform possible mining users of AC variable frequency drive attributes.

Jan 1, 1998

The National Mine Health and Safety Academy near Beckley, W. Va., is dedicated to reducing accidents and improving health conditions in the mining industry through education and training. Though this basic mission remains unchanged, the Academy now serves a much broader mining community than it did when established in the late 1960s. From its original emphasis on training federal coal, metal, and nonmetal mine safety inspectors, the Academy has expanded its programs to reach mining industry and labor representatives, state agency employees, and university students taking mining-related courses. The Academy's resident programs, short courses, seminars, and continuing education courses cover a wide range of subjects and various experience levels, but all have been developed with one idea in mind - to reduce accidents and health hazards through education and training of the widest possible audience.

Jan 11, 1979

By Cayo Soto

Mining activity is important for the development of humanity. This development must be understood from the Academy where it allows showing alternatives for the industry performance. Likewise, these mining companies need to improve their results. Historically, a few years ago the application of the ESG (Environmental, Social and Governance) criterion was verified, which is positioned as a factor/regulator in the design of the performance of industries in general. ESG as an integral part of the concept of sustainability serves as a tool to conceive mining without conflicts and with a reputation based on trust in the interrelation of the university, industry and society. Therefore, the academy must strive for new knowledge in a way that allows it to continue in the virtuous circle of constantly feeding it. In this context, the best mining practices are implemented in constant questioning of their activities. The scientific essence of the industry supported by the academy developed in an operational dynamic is addressed. Finally, the objective of this research work is to interrelate 3 variables: ESG, Academia, and the Mining Industry, where the transition of knowledge and the role of each variable in relation to each one can be understood. This allows for an additional understanding of mining in the future with new mental attention.

Feb 1, 2025

Coal exports are forecast to grow strongly, so that coal is likely to remain very important to Australia for the foreseeable future. However there is no sign that prices or profitability will rise of their own accord. Therefore the intense squeeze on costs will continue for the foreseeable future. This will mean lower manning, more outsourcing and probably an increasing rate of company attrition. As well, the political pressure from the greenhouse debate is only going to intensify and the pressure on the Federal Government after Kyoto is likely to be irresistible.

Jan 1, 1998

By D Eschebach, D Mathewson

A belt press filter (BPF) handbook containing practical information for the reference of plant designers and operators has been created as part of Australian Coal Association Research Program project C23040. The handbook combines research and experience with newer generations of equipment and circuitry. BPFs are increasingly finding application in the dewatering of thickener underflow tailings slurries due to changing environmental regulations, difficulty obtaining tailings storage facility approvals and limited water availability. Sources of BPF inefficiency and low availability stem from a lack of understanding of the key operational parameters that affect their performance. This lack of understanding typically leads to increased operational expenditure due to suboptimal reagent dose rates and increased maintenance costs, or decreases in plant availability due to excessively high filter product water contents and equipment failure. It is essential for the continued economically competitive operation of Australian coal handling and preparation plants that complex factors affecting BPF operational performance are clearly defined and understood. Installation and operation handbooks are often provided to sites with new installations, but these manuals are manufacturer- or even model-specific and are often focused on mechanical maintenance. The handbook identifies industry ‘best practice’ and improvements developed by other sites, such as extra spray bars, air system bleed valves, guarding designs, feed and filtrate protection screens and roller tensioning systems. Equations to predict optimum operating conditions – such as free moisture, belt tension and reagent dose rates, with simple feed-specific variable inputs – have been developed from site-specific test work. The correlations developed provide a benchmark for plants to attempt to achieve. This provides operators and process engineers with a tool to explain BPFs and assist them in optimising the performance of BPF dewatering plants of both contemporary and less modern design.CITATION:Mathewson, D and Eschebach, D, 2015. ACARP belt press filter design, operation and maintenance handbook, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Folwell, G Phillips, F Gassner

Geomembranes selected for various applications often start with considering target properties developed by industry organisations such as Geosynthetic Research Institute (GRI), and test methods developed by ASTM and other Standards organisations The geomembrane types are typically, initially selected based on manufacturers recommendations and chemical resistance data from the manufacturer or industry knowledge. Geomembranes considered for this project included materials with material properties that exceeded the minimum target values of various test methods. The difficulty is in selecting which parameters are most important for a particular application and also what service life can be expected for the geomembrane under various chemical and environmental exposure conditions. Accelerated aging testing of candidate geomembranes in simulated exposure conditions can be useful to select the preferred geomembrane and predict the service life of the geomembrane under different exposure conditions. The exposure conditions of immersion in acidic tailings liquor, splash zone and freeboard zone were considered for evaporation ponds on a site with significant heat and UV radiation. Candidate geomembranes considered a range of different types of polyethylene liners. The results of the accelerated aging testing have allowed the selection of the geomembrane for the range of exposure conditions and evaluation of the expected service life of the geomembrane.

Jul 1, 2021

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

By B Miles, D J. Williams, J Ahn, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. It is therefore important to understand the mechanisms and degree of degradation likely to occur within coal mine spoil of different qualities.To investigate this, five clay mineral-rich coal mine spoil samples were collected from the Bowen Basin, and each sample was subjected to wetting and drying cycles to simulate degradation that could be expected on wetting-up in situ, with their particle size distribution analysed both before and after degradation. These results were compared with the results of a modified slake durability test, in which the entire sample was tested.The paper presents the results of the accelerated degradation and modified slake durability tests on each of the five spoil samples. These results were related to the physical and geochemical characteristics of the samples, which highlighted their importance. The modified slake durability test may be used to rapidly simulate the expected in situ degradation of coal mine spoil on wetting-up, enabling susceptible spoil materials to readily be identified.CITATION:Vangsness, T A, Williams, D J, Ahn, J and Miles, B, 2018. Accelerated degradation and modified slake durability testing of clay mineral-rich coal mine spoil, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Xiaobing Yang, Abhishek Lahiri, Animesh Jha

"In the FFC-Cambridge process, the cathodic dissociation of oxide and CO/CO2 production on carbon anode is the basis for metal production in a CaCl2 bath. By using an inert intermetallic anode, the CO2 evolution can be eliminated altogether with acceleration in the electro-reduction kinetics. At present the process suffers from slow reduction kinetics of TiO2 to Ti metal, which can be enhanced significantly by the incorporation of alkali species in the TiO2 pellet at the cathode and in the CaCl2 bath in the presence of an intermetallic inert anode. Nearly full metallization with greater than 99% of Ti metal containing 1500 ppm of oxygen is possible to achieve in less than 16 hours of electro-reduction. Analyses of phase composition and the microstructures morphology in fully metallized pellets revealed the presence of localized solidified Ti layer, indicating that fast reduction process also involved formation of liquid phase as middle stage reaction. In addition, in situ creation of porosity and maintain higher current level during electrolysis process were two key factors to fully reduction of TiO2.IntroductionDuring cathodic dissociation of TiO2 in a CaCl2 bath and anodic evolution of CO2 on a carbon anode, which is the basis for the FFC Cambridge process [1], the rate of metallization slows down due to the formation of CaTiO3 at the reaction interface. Calcium and alkaline earth perovskites are known for their poor electrical conductivity which adversely affects the overall electro-reduction. One of the ways to increase the porosity is via the addition of polyethylene precursors in the pellet or by directly starting from perovskite [2, 3]. The experimental evidences shown in the literature confirm although the speed of reaction increases, but a complete or near complete metallization is not possible by enhancing the in-situ porosity alone, as the insulating perovskite is very slow to decompose under the equilibrium that prevails in the cell. Plethoric evidences on carbon anode show with the current decrease gradually, and finally stabilize at a very low value between 0.2 and 0.4 A, which is a testimony of the presence of perovskite insulating barrier in the current path. Our aim in this paper is to demonstrate the mechanism of enhanced electro-reduction when alkali ions are present in the oxide pellet at cathode and in the bath. We also show for the first time the use of an intermetallic anode for Ti-metal production using the FFC Cambridge process."

Jan 1, 2009