Search Documents

By M. Solomon

Giant, sediment-hosted lead-zinc deposits in northern Australia fonned during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6",Wm-3, probably sufficient to fonn giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of IOS to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-fonning fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

By Jennifer B. Leinart, Otto L. Schumacher

JIM ARNOLD: Our next speaker is Otto Schumacher. He's president of Western Mining Engineering in Spokane, Washington. His company offers services in the area of mining feasibility analysis and publishes Mining Cost Service. Otto's talk will be "Are Metallurgists Overpaid?" [laughter] I know one that's not. [laughter] OTTO SCHUMACHER: I really think it's kind of a dirty trick for Doug to put me up here and pose that question since I'm a mining engineer. However, it's probably most appropriate that a mining engineer address the question because I can be more objective than the rest of you. [laughter] SPEAKER. Otto, do you promise to say something nice about metallurgists? [laughter] OTTO SCHUMACHER: I'll see how much time I have. [laughter]

Jan 1, 1998

Alternatively are they a necessary evil'? Exploration geologists are a much higher profile group but then again the higher they are the bigger they Bill. At a mine site they are reluctantly being accepted as equals by mining engineers given the requirements of the `Code' in the reporting of Ore Reserves. How best can mining geologists service their customers? Are more revealing questions to be answered in who are their customers? In the past mining geologists lived isolated existences pouring over plans and sections, now with user-friendly software packages available and the use of LAN, mining geologists and mining engineers talk electronically - God forhid what the future might hying - they might even talk to accountants and metallurgists!

Jan 1, 1997

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

By George C. Bravner

WITH the great expansion currently being made in the aluminum output of the United States, not only by the company that has heretofore been the sole producer but by a now organization in the field it is only natural to wonder to what degree the; ore reserves of the United States can contribute to the growing consumption. For the three-year period 1937-&apos;39 the U.S. Bureau of Mine&apos;s figures indicate that the annual domestic production of bauxite averaged about 370,000 long tons, compared with average, annual import of about 194,000 long tons. About 85 per cent of the imports came from Surinam, nearly all of which went into aluminum manufacture. Not all of the or -kipped from mines in the United States is used to make alumimun however as Bureau figures indicate that in these three years an average of only 48 per cent of the domestic ore shipment were so used the abrasive chemical and other industries taking respectively 27, 21, and 4 per cent of the output. The recent increase in the demand for bauxite has been of course in it use for aluminum manufacture. This as is well known is largely attributable to the world race for supremacy in

Jan 1, 1941

By P B. Swart, P D. Erskine

Despite an increasing focus by media, communities and activists driving an elevated regulatory focus in Australia and indeed some other mining jurisdictions, the mining industry globally has had limited successful mine lease relinquishments and transfers to support a next land use.Critique from anti-mining lobbyists frequently uses the large estimates from historically abandoned mine sites to influence risk-averse regulatory reforms to improve environmental performance. The mine rehabilitation regulatory processes in Australia, and specifically in the State of Queensland, are thus largely in place to prevent mining operators from abandoning their obligations.Regulatory responses to the lack of mine rehabilitation and closure performance in the last five to ten years have primarily focussed on compliance and enforcement of rehabilitation conditions in environmental approvals. Additionally, financial assurance measures have been tightened to protect against abandonment of rehabilitation obligations by the Industry, including the Chain of Responsibility legislation (Queensland Government, 2016b) in April 2016, to hold to account those who have benefitted from mining and processing/refining projects, and then avoid their environmental obligations.CITATION:Swart, P B and Erskine, P D, 2018. Are our closure planning and regulatory processes adequate to identify, quantify and appropriately transfer residual risks after successful mine rehabilitation?, in Proceedings Life-of-Mine 2018, pp 155–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A. C. Johnstone

The aim of the study is to determine if pit lakes are a sustainable coal mine closure option in South African. The water balance, chemistry, limnology, and bacterial population of three selected pit lakes were investigated. The lakes are in the three major coal basins of South Africa and are associated with different lithologies and mining methods. The major factors driving the water balance of the pit lakes are direct rainfall, runoff, inflow from old mine workings, and groundwater infiltration, with the major losses being evaporation or discharge onto surface. The study indicated that pit lakes can be designed as ’terminal sinks’ to provide a sustainable mine closure option. The pit lakes sampled have an alkaline pH, and mostly a sodium/calcium sulphate water with total dissolved solids content of less than 3000 mg/l. The phytoplankton and microbiological data indicates that the pit lakes support aquatic life. The study shows that correctly designed pit lakes can be an environmentally sustainable closure option for South Africa’s coal mines. A suggested design manual has been developed to assist mine owners and regulators in developing sustainable coal mine pit lakes as a closure option.

Oct 1, 2021

By B. Yu, N. Verbaan, A. Mezei

The recent 20 years witnessed a boom and bust in the nickel laterite industry. Most notoriously is the story of the first three Western Australian nickel laterite projects which all suffered major ramp-up issues. Many hard lessons were learned by the industry and it has been widely reported that the major contributing factors included insufficient testing as well as a limited understanding of the materials handling characteristics at the front-end stage of the flowsheet. This paper compares the current "race to production" in the REE industry to the laterite industry 20 years ago and addresses the fundamental question: ‘Have mining and exploration companies with rare earth projects learned from past lessons and are they doing sufficient and appropriate testwork to prevent failure’? The authors will provide the perspective of a commercial metallurgical laboratory that has gone through the laterite cycle and is active in the present REE cycle.

Jan 1, 2014

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By R E. Hobbs, O Grabandt, C Das

Mine hoisting is carried out from depths of up to 4 km. At extreme depths, the ropes are so heavy that a large part of their capacity is employed in lifting themselves. Consequently, deep mines have an intermediate winding station. Even at lesser depths, the weight of steel wire rope reduces the possible payload. Of course, steel wire ropes have, over the years, demonstrated exceptional reliability and acceptable lifetimes. The use of steel is supported by well established operating rules and sound NDT methods. However, lightweight ropes made from synthetic fibres could be of great benefit to the industry, with the prospect of eliminating two-stage winding and substantially increasing the payload. Initial tests, in cycling over sheaves, have demonstrated that an aramid co-polymer fibre, Technora« is a potential candidate for this type of service. This paper presents results of testing carried out on aramid co-polymer and other synthetic fibre ropes. These results hold out the prospect of exceptionally long lives. Possible NDT methods are explored including optical fibres with optical time domain reflectometry or with Brillouin scattering, plus a method based on carbon fibre continuity. The introduction of aramid co-polymer ropes will require extensive testing and a program is proposed in the format of a Joint Industry Project.

Jan 1, 2005

By P A Ferenczi

The Proterozoic iron oxide related Au-Cu-Bi (Tenant Creek style&apos;) deposits at Tennant Creek can be classified as syntectonic polymetallic hydrothermal replacement type mineralisation. These deposits have characteristics in common with a number of other Proterozoic iron oxide (Cu-U-Au-REE) hosted deposits in regions which include Southeast Missouri, USA; the Kiruna district, Sweden; the Great Bear Magmatic Zone, Canada; the Stuart Shelf, South Australia; and the Wemecke Mountains, Canada. Similarities between these and Tennant Creek style deposits include: 1. Tectonic Setting: Formed at shallow crustal levels (

Jan 1, 1994

By Henry Howe

- §1. INTRODUCTION.-Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in the familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal re-crystallizing. The network in Fig. 22 and the parallel N.-70°-E. lines in Fig. 21 are slip bands in copper.

Jan 3, 1915

Discussion of the paper of HENRY M. HONE and ARTHUR G. LEVY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 587 to 600. J. E. STEAD, Middlesbrough, England (communication to the Secretary*).-As I have not personally studied the question of quenched and distorted manganese steels I cannot give any information of my own on the subject. The question as to whether certain indications in strained manganese steel are "slip bands" or "twins" might be settled, I think, by heat tinting-a method I have applied with success to certain meteorites and other alpha irons in which there were undoubted twins. After polishing and very slightly etching with picric acid in alcohol, and then "heat tinting," the colors assumed by the twinned strata and the adjoining metal are different. The reason of this, as I have proved repeatedly, is that different faces of the iron crystals are differently attacked by oxidizing and other reagents, and consequently some of the faces take temper oxidation tints more rapidly than others. This simple method enables one to determine with certainty whether the "twins" are actually, twins and differently oriented from the bed in which they are found. After correspondence with Dr. Howe, I think we both agree that Neumann lines should not be called "lines" but "bands" or "strata," preferably the latter term, as I have found that they are more or less continuous throughout the crystals, and it would be just as improper to call the edges of cementite plate by the term "lines" as to call stratified twins by the same term.

Jan 5, 1915

By John B. Hastings

CHIEF among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr 1 is quoted, because it sets forth Mr. Spurr&apos;s theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. &apos;&apos; The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars&apos; worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerous, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the Drink-

Jan 1, 1913

By I Ritchie, G Lane, C Morley, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa project in Peru. The project has a lower grade oxide orebody overlaying the higher grade sulfide orebody. The oxide ore is treated by acid leaching; consumption of acid is high and is managed by vat leaching rather than the more conventional heap leaching process.The leaching process uses ore crushed to 100% passing 8 mm to optimise copper recovery. Acid consumption generally increases with a higher proportion of fines. Marcobre is investigating a three-stage crushing circuit with high pressure grinding rolls (HPGR) in the third stage, instead of the more conventional four-stage cone crushing circuit. The use of HPGR can result in higher fines production due to the higher compression forces in the crushing zone. This paper reports on the outcomes of the test work completed by Marcobre in 2016 and 2017 to manage fines production and compare the use of HPGR with conventional crushing on a high acid consuming ore.At moderate pressing forces, a HPGR crushing circuit appeared to produce similar size distributions to cone crushing. On average, both the copper recovery and the acid consumption in subsequent vat leaching were higher with HPGR crushing than with cone crushing.CITATION:Lane, G, Morley, C, Yataco, D and Ritchie, I, 2017. Are there differences in size distribution when comparing conventional crushing and HPGR?, in Proceedings MetPlant 2017, pp 60–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By I. M. Ritchie

Cyanide owes its great success as a lixivant for gold to the great strength of the Au-CN bond. A replacement for cyanide must similarly be a strong complexant for gold (I) or gold (III). The various alternatives are briefly considered and it is concluded that only thiosulfate has a reasonable chance of replacing cyanide as a relatively non-toxic lixivant at the present time. However, there are considerable technical problems to be overcome before thiosulfate can be considered to be a realistic alternative to cyanide. Firstly, the leaching of gold using aerated ammoniacal thiosulfate with copper as a catalyst is a complex process which needs to be understood and controlled carefully in order to achieve maximum recoveries with minimum reagent losses. Secondly, there needs to be an option similar to the CIP process for recovering and concentrating the dissolved gold thiosulfate complex from pulps produced in the processing of low grade gold ores. The prospects for overcoming these technical&apos; challenges are evaluated and discussed.

Jan 1, 1998

By William B. Plank

IN this paper are presented the results of a complete statistical survey of the enrolment, courses and degrees, and the employment situation of recent graduates in all of the 46 institutions in the United States, including Alaska, and four of the six schools in Canada that grant degrees in mineral technology. The data were collected by the writer by means of a questionnaire in December, 1933, to which all the institutions, except one, replied. Included also are data of a similar study made by the writer in May, 1933, for the S. P. E. E. summer session of mining and metallurgical teachers at the University of Wisconsin and published in the Journal of Engineering Education for December. 1933. Some of the data of a paper of the writer&apos;s entitled, "The Trend of Mineral Engineering Student Enrolment in the United States," read at the A. I. M. E. meeting on Feb. 16. 1931, are given for comparison. Acknowledgment is made to all the administrative officers of the institutions who took the time from their busy lives to supply the in- formation asked for. Their fine cooperation has alone made possible these two surveys with a completeness of detail never before attempted

Jan 1, 1934

By Ron Hatch, M. K. Witte

"INTRODUCTIONThe proper selection of carbon for a gold carbon in pulp (CIP) circuit involves careful evaluation of several physical, chemical and economic factors. A series of evaluations are required to maximize gold recovery at the lowest capital and operating costs, whether the carbon is selected for an existing gold mill circuit or a new mill under design.Although evaluation may proceed through various stages, it is the intent of this paper to outline some of the preliminary testwork that should be carried out to screen potential carbons for a particular application.An examination of the specification sheets supplied by the various carbon manufacturers may indicate some desirable properties on which to make cursory selection. This exercise by itself will not provide the basic data needed for selecting the best carbon for a particular ore pulp and metallurgical circuit. The necessity of further metallurgical evaluation is indicated by the fact that different carbons perform differently depending on the physical and chemical nature of the leach pulp. In the case of an existing mill, actual leach slurries using mill water are available and should be used for testwork. In the case of new mills, leach pulps must be prepared to simulate the proposed circuit.Five coconut shell activated carbons were obtained from various suppliers, all reported to be 6 x 16 mesh carbons recommended for CIP circuits. A metallurgical evaluation was made utilizing two leach pulps with significantly different characteristics. This paper describes the test procedures utilized and the results obtained from the testwork."

Jan 1, 1985

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977