Search Documents

By R. Kaund

"Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence, preventative measures can be taken to avoid severe hazards to mine safety.INTRODUCTIONWith the increasing demand of mineral resources and depletion of near-surface ores, the depths of underground mines have made the mining activities one of mankind’s most dangerous types of work (Ortlepp, 2005). The Mine Safety and Health Administration (MSHA) defines rockburst as “a sudden and violent failure of overstressed rock resulting in the instantaneous release of large amounts of accumulated energy.”The types of rockburst can be classified into three types: (1) strain burst, (2) pillar burst, and (3) fault slip (Müller, 1991). Strain burst is the most common type of unstable rock failure in underground openings, where the intensity and scale are usually smaller than pillar burst and fault slip (White and Whyatt, 1999; White, Williams and Whyatt, 2002; Ortlepp, 2005). The cause of strain burst can range from shattering of rock under high stress concentration to buckling of discontinuities parallel to underground openings. The occurrence of pillar burst also depends on the stress and discontinuity conditions in the rockmass, but pillar burst usually involves the sudden loss of strength in the core or foundation of a pillar (Whyatt and Blake, 2002; Kias and Ozbay, 2013; Khademian et al., 2016). Fault slip or slip burst can be either slip along pre-existing discontinuities or shear failure in the rockmass, when the shear stress is larger than shear strength in the fault (Rice, 1983; White and Whyatt, 1999; Sainoki and Mitri, 2014). The consequence of fault slip can vary from very small rockmass damage to consequential rockmass damage, but large seismic magnitude does not always result in large rockmass damage (White and Whyatt, 1999; Whyatt and Blake, 2002)."

Jan 1, 2018

By T. Verdel, Y. Gunzburger

Rockfalls are major and essentially unpredictable sources of danger, particularly along transportation routes (roads and railways). Thus, the assessment of their probability of occurrence is a major challenge for risk management. From a qualitative perspective, it is known that rockfalls occur mainly during periods of rain, snowmelt, or freeze-thaw. Nevertheless, from a quantitative perspective, these generally assumed correlations between rockfalls and their possible meteorological triggering events are often difficult to identify because i) rockfalls are too rare for the use of classical statistical analysis techniques and ii) all intensities of triggering factors do not have the same probability. In this study, we propose a new approach to investigate the correlation of rockfalls with rain, freezing periods, and strong temperature variations. This approach is tested on three French rockfall databases, the first of which exhibits an outstandingly high frequency of rockfalls (approximately 950 events over 11 years), whereas the other two databases are more typical (approximately 140 events over 11 years). These databases come from (1) the national highway RN1 on La Réunion Island, (2) a railway in the Bourgogne-Franche Comté region, and (3) a railway in the Auvergne region. Whereas a basic correlation analysis is only able to highlight an already obvious correlation in the case of the “rich” database, the newly suggested method appears to detect correlations even in the “poor” ones. Indeed, the use of this method confirms the positive correlation between rainfalls and rockfalls on La Réunion Island database. This method highlights a correlation between cumulative rainfalls and rockfalls in the Bourgogne region, and it detects a correlation between the daily minimum temperature and rockfalls in the Auvergne region. This new approach is easy to use and also serves to determine the conditional probability of rockfall function of a given meteorological factor. This approach will help to optimize risk management in the studied areas based on their meteorological conditions. Nevertheless, even if some rockfalls are correlated to meteorological factors, other seems to occur independently of these factors, which highlights the unpredictability of rockfall hazard.

Jan 1, 2015

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Keith Jones, Michael Francis

Contract 240 of the Channel Tunnel Rail Link comprises construction of twin4.7 km long running tunnels through a densely populated area of East London. The tunnels were constructed by EPBM in Sands and Sandy Clays, passing 4.4 m below the existing London Underground tunnels, and at depths of 20–30m below ground level beneath the Great Eastern railway lines into London Liverpool Street and a series of railway bridges and hundreds of buildings. This paper describes how the project team managed the challenges relating to the issue of settlement: mitigating settlement effects, prioritising the structures to be assessed, controlling resource expenditure by incentives and flexible response to urgent work relating to unforeseen events such as ground collapse and discovery of unusual structures.

Jan 1, 2005

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen's University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne's pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By Eugene F. Mehr, Dennis C. Martin

"Development of the final slope for the 340 m (1200 ft) high hanging wall at Cassiar Mine precipitated an area of deep seated instability involving an estimated 17.6 million tonnes. The deformation mechanisms involved squeezing of soft deformable serpentinite rocks in the toe which caused planar sliding and graben toppling of the stronger sedimentary rocks in the middle and upper sections of the slope. Although movement rates up to 150mm/day were recorded, by understanding the controls on failure, the mine was able to install a suitable monitoring system and complete the open pit with only minor loss of the mineable ore. Accelerated mining was required in the last full year of operation. This paper describes the deformation behaviour, failure mechanisms and back analysis results for the failure. The monitoring systems and operational aspects related to the failure are also presented.IntroductionCassiar Mine is located in steep mountainous terrain in northern British Columbia approximately 1200 km north of Vancouver (Fig. I). During the final mining phase of the open pit, instability developed in the approximately 340 m high hanging wall (east wall) slope. A unique graben toppling mechanism was identified based on detailed assessment of slope monitoring data and visual observations. Comprehensive slope monitoring enabled mining to continue even though movement rates as high as 150 mm/day were being recorded. Three-dimensional limit equilibrium back analyses and numerical modelling have been used to assess the various controls on the slope movements and to understand the failure mechanism."

Jan 1, 1993

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By M F. Navarrete

During 2003, different plastic stemming plugs (Cats«, Stemtite«, and Taponex«) were tested in EscondidaÆs Mina Sur, to determine the effect on gas retention time when used in conjunction with drill cuttings in production shots with a blasthole diameter of 10 5/8ö. Longer retention times were expected to provide greater fragmentation and muckpile looseness. In order to determine which plug showed the greatest enhancement of stemming retention, 17 trials were carried out û in the first seven tests, only the Cats were used, in the following five tests, a combination of Cats, Taponex and Stemtite were used, and in the last three tests, only the Taponex plug was used. In the last two blasts, drill cuttings were used without stemming plugs as a benchmarking exercise. Blasts were filmed with a high-speed camera, which could record the detonation times of holes using rolls of shock tube tied to stakes at the hole collars, to act as flash indicators. The camera allowed measurement of the time between charge detonation and the commencement of stemming ejection. In order to obtain the statistical parameters of each one of the stemming plugs used in the 17 trials carried out, the Minitab software was used and a data base was created for it, corresponding to each stemming configuration with the retention time obtained from the filming. Once it was determined which stemming plug provided the greatest enhancement of stemming retention, the impact on the fragmentation was analysed using the WipFrag image analysis software to estimate the muckpile size distribution.

Jan 1, 2004

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture. These equations are called geometric probability equations.Davy derived a geometric probability equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. This covariance can be used to measure the variance of the particle composition distribution of each mineral. The equation as presented by Davy requires textural information; however the equation was modified by Gay to be more directly applied to particle sections and linear intercepts. The variance obtained from applying this equation is fundamental to the binary stereological correction procedures developed by Gay and his colleagues; the covariance is fundamental to the multiphase stereological correction.Thus far, validation of both the binary and multiphase stereological correction has been achieved using numerical simulation. This paper shall present results comparing the covariance (and variance) estimates from Gay’s equation with actual three-dimensional information obtained from serially sectioning particles. This involved mounting a set of particles and continuously sectioning all particles uniformly so that the three dimensional structure of the particles could be obtained.The mineralogical data to which the equations described above were applied were derived from two individual size fractions from a hard-rock titanium deposit. The deposit contains a range of minerals and of mineral textures and the two size fractions selected were:"

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By David Oliveira

"INTRODUCTIONOne of the key drivers for the selection of a mechanized tunneling method in good quality rock masses is a good excavation advance rate. In order to achieve satisfactory advance rates, a good geotechnical performance of the rock grippers in main beam open tunnel boring machines (TBM) is required, besides other factors related to ground support and the performance of the cutter head.One well known potential issue of main beam gripper TBM is associated with the bearing capacity of the tunnel side walls while crossing fault zones or poor rock masses in general. Such a mechanism is similar to that of footings on rock and perhaps the most common problem associated with gripper performance. Depending on the quality of the rock, the rock under the gripper contact may experience significant damage and crushing (Figure 1), eventually affecting the TBM advance rate due to a lack of tunnel wall reaction/support. Such a mechanism is primarily dependent on rock quality, applied loads and gripper size.In the case of large diameter TBMs (e.g., D > 12 m), a second potential failure mechanism may arise associated with the loss of confinement within a rock pillar between twin tunnels, even in good quality rock but particularly in bedded sedimentary strata. Punching of the rock pillar may develop due to excessive shear along bedding partings and sub-vertical joints (Figure 2), particularly under a low stress environment. As a result, this mechanism is dependent on both the rock pillar width between twin tunnels and stress conditions around the tunnels, in addition to the previous factors described for the first failure mechanism."

Jan 1, 2016

By Aspinall T. O

This paper discusses the identification and assessment of risk for mining developments particularly for open pit mining. A distinction between sensitivity studies and risk analysis is developed, demonstrating the importance of geological and mining engineering judgement -as applied by experienced practitioners to the analysis and assessment of risk in such projects. Technical and financial risk analysis are discussed under: ò mineral resources and ore reserves; ò mining and processing methods; ò project construction; ò financing; and ò costs and commodity pricing predictions.

Jan 1, 1994

By T. B. Whitmoyer, J. E. Sneckenberger, M. A. Jerabek, C. F. Stanley

The measurement of acoustic impedance at frequencies up to 6,400 Hz has been proposed as a diagnostic tool to yield more detailed information about lung condition. A three generation branching system of plastic Y-tubes has been constructed. The impedance of the branched system is measured by an impedance tube using the two-microphone technique. The impedance spectrum is used to calculate the reflection coefficient spectrum, which is converted to an impulse response by an inverse FFT. The area function is extracted from the impulse response by the Ware-Aki algorithm. Measurements of acoustic impedance of the branched system were made for several different end conditions of the eight terminal outlets. The outlets were either blocked with modeling clay, plastic packing material, or aluminum blocks or were unblocked. Six measurements were made of each configuration. In general, the more outlets blocked, the larger the shift to the right of the impedance magnitude peaks for frequencies above 3000 Hz. The impedance magnitude peaks for the plastic packing material were shifted in frequency to the right relative to the peaks of the other system terminations. The impedance magnitude peaks for the clay and aluminum system terminations were significantly different in magnitude but not shifted in frequency. The area functions at the end of the branched system were significantly different (a > 99%) for most of the end conditions. Area functions for the modeled branched lung systems between the end of the impedance tube and the termination outlets of the branched system were similar but distinctively different for the various end conditions. These results indicate that the two-microphone technique can sense small changes in the terminating end conditions of a rigid system of branched tubes and thus may sense impedance changes due to lung disease in the conducting airways. Keywords: acoustic impedance, lung model, area function.

Jan 1, 1991

By D. M. Milne, H. H. Kanduth

INTRODUCTION The past few years has seen an increased interest in the determination of statistically valid properties of a rock mass. The increased use of computer modelling for the study of rock excavation behaviour has created a need for upper and lower statistical bounds for the properties of a rock mass being modelled. Obviously, to determine the statistical properties of a large volume of rock, many samples must be tested - an expensive proposition when using conventional testing facilities and procedures. As a result of high costs per sample, sufficient tests for statistically valid results are rarely done. In an effort to reduce both sample preparation and test facility costs, an instrument called the Bemek Advanced Rock Tester (BRT) was developed in Sweden. With a total weight of approx. 35 kg, the BRT is portable and sells at a small fraction of the cost of a conventional testing machine. It is comprised of a small 65 KN loading frame with attachments for a variety of tests (see Table 1) , a hand operated hydraulic pump, an electronic balancing unit and a programmable microprocessor. The microprocessor is capable of storing data, performing arithmetic operation on, and printing signals from, a transducer and two strain gauges. A detailed description of the apparatus is given by G. Swan et al. (1). The proposed test strategy involves first a 3-point flexure test on a notched core specimen, followed by a 4-point flexure test on the separated specimen halves. Finally, point load and Brazilian tests can be carried out on the quarter parts of the original specimen. Thus specimen preparation is kept to a minimum. These and other perceived advantages have prompted the purchase of this machine and an evaluation of its suitability to provide data on mechanical properties of intact rock for numerical modelling and rock mechanics design at Noranda's underground mines. Details of its performance evaluation and experiences with the unit are discussed in the following sections. [ ] INITIAL OPERATING EXPERIENCE During the commissioning stage the BRT had, or developed, a series of problems, some of which seriously affected its operation. Below are some examples. Poor documentation was the most serious problem encountered. Confusing instructions for the 4-point bend test installation and its microprocessor programing, as well as poor and ambiguous information on the calculation of gauge factors, are some of the difficulties which had to be overcome. Meehan~cal problems occurred, including failure of the hydraulic pump, as well as electronic difficulties with the microprocessor. Other problems with the printer, requiring its replaceqent, were fortunately covered under warranty.

Jan 1, 1986

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By Stephan A. Jefferis, Adrian H. Bath

"This paper draws together some themes on the durability of barrier systems, and particularly cementitious systems. For contaminated land and water retaining structures, durability can be poorly addressed at all stages of a project, from specification, to barrier material selection, barrier design including toe-in and through to performance assessment in operation. Permeability (hydraulic conductivity) is a dynamic property which will vary over time as reaction processes propagate through a barrier. However, laboratory testing, when undertaken, tends to be focused on short term tests with aggressive chemicals so that the effects of longer-term processes such as carbonation and leaching by permeating water are missed. For water retaining structures, carbonation and leaching actually may be the most significant processes affecting barrier performance as the groundwater adjacent to many water bodies can be otherwise rather benign (as regards bentonite and cementitious systems). These and other reaction processes have been modelled in the arena of nuclear waste repositories and procedures are well recognised. However, such procedures have yet to be widely adopted for the assessment of other barrier systems.INTRODUCTIONOver the last few decades there has been an enormous amount of laboratory research on the durability of barrier materials or more specifically papers reporting the results of permeability tests. Unfortunately there is a much smaller literature on scaling test results to barrier dimensions in the field or to required design lives. Although in the geotechnical industry durability research has been largely laboratory based, in the nuclear industry where relevant timescales are multi-millennia rather than decades, research has been heavily underpinned by geochemical modelling. A significant purpose of this paper is to examine the tools that may be used to analyse the results of tests on barrier materials used in geotechnical engineering, for example, for water retaining structures and contaminated land and draw the attention of the construction industry to the potential of the modelling procedures developed for nuclear repository assessments. Modelling can help to identify underlying processes and so augment information from laboratory testing focused on changes of physical properties such as permeability and strength."

Jan 1, 2016