Search Documents

By Donald T. Mylar

It is axiomatic that in designing a bulk material handling system the primary consideration is the functioning of the machines. The structure is secondary -its reasons for being are to support, enclose and provide access to the machine, for servicing. This results in a wide variety of supporting structures. Other considerations are: plant layout, local soil conditions, climate, local laws and codes, and last, but by no means least, the Customer's wishes.

Jan 1, 1971

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By P. J. Conners, H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of moving bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at the same speed and without impact, then about 90% of all belt conveyor problems would disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. Some general design criteria required for proper transfer of materials from one conveyor to another are established and discussed. Specific attention is given to loading chutes and skirting.

Jan 1, 1973

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and'reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By J. P. Van Kleunen

9.3-1. Introduction. The demands of industry for handling materials at higher rates and at reduced costs have had a very significant effect on belt conveyor technology. Although the general appearance of the belt conveyor today is essentially the same as it has been for the past several decades, the similarity ends there. Each component comprising the conveyor system has been continuously improved through design and materials technology to enable present conveyor systems to operate at ever-increasing rates and reliability. For example, twenty years ago the strongest commercially available, fabric-reinforced conveyor belting had a tension rating of 50 lb per ply-in. Currently, fabric-reinforced belts are available with ratings of 350 lb per ply-in. and steel cable reinforced belting is available with tension ratings of 3000 lb per in. of belt width (3). These technological advances have therefore enabled the belt conveyor to not only attain acceptance as a preferred method for in-plant movement of bulk materials, but also to be used for long distance transportation of bulk materials, particularly in areas of adverse terrain. The information contained in this chapter is intended to assist the reader to make basic decisions regarding the use and application of a conveyor system. The design of an overland conveyor transportation system or an in-plant process conveyor is accordingly beyond the scope of this article. Many comprehensive technical works covering the design of a belt conveyor are currently available from the manufacturers of materials handling equipment (6, 7, 9, 11). The design handbook published by the Conveyor Equipment Manufacturers Association is particularly recommended (2). 9.3-2. Conveyor Capacities. One of the most important factors in determining the proper size of a conveyor system is the rate at which material must be handled. Although tables and charts are available to the conveyor designer to assist him in his selection of conveyor components, only the

Jan 1, 1968

Although the title of this paper permits a very broad scope for discussion, I propose to deal mainly with those aspects of design part- icularly related to rook filling, the'theme of this conference. The unique suitability of belt conveyors for the continuous economical delivery of materials into or out of underground workings, is well established and needs no elaboration. The facility with which conveyor units, comprised of modern modular components, can be adjusted to lengthen or shorten, their ability to be readily repositioned to suit the develop- ment of a work pattern and their virtues as low noise, reliable transport media, are already accepted by all who are involved with the mining industry.

Jan 1, 1973

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By J. Kircher

Nevada Goldfields' Aurora Mine consists of a 270 mtpd (300 tpd) precious metals mining and milling facility located 28 miles southwest of Hawthorne, Mineral County, Nevada and lies within five kilometers of the Nevada-California border. (Figure 1) Ore production presently is derived 85% from an open pit source with the balance from underground. The Aurora Mill is a compact conventional cyanide plant utilizing a carbon-in-leach extraction process followed by stripping of loaded carbon and electrowinning at Nevada Goldfields Kingston Mine, located near Austin, Nevada. Production commenced in December 1987 and annual gold production is currently 20,000 troy ounces of gold and 22,000 troy ounces of silver per annum, produced at an average cash cost of $178 per ounce of gold. Tailings handling at, Aurora was originally accomplished using a belt filter press producing a solid cake that was then transported to a final storage area. Although overall operating costs at the mine were' in the lower percentile of producing gold mines, the tailings handling portion of the operating costs were inordinately high.

Jan 1, 1989

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By M Olsen

"Segregation of conveyor roadways is a ventilation practice that is being increasingly applied in Australia. It is largely driven by the legislated requirements in Queensland pertaining to separation of escapeways from the mine. This legal requirement was based on a recommendation from the Moura No. 2 WardenÆs Inquiry (Windridge, 1996) into the mine disaster that claimed 11 lives. The report recommended: ... the introduction of a requirement for all underground mines to have one intake airway that is completely segregated from other parallel intake airways so as to provide two separate means of egress from the mine via an intake airway.This recommendation seeks to assist mine workers in escape from a mine after a fire by providing them with an airway that is free from smoke or contaminants.The concept of an airway being æcompletely segregatedÆ is an ideal that is challenging to implement in practice when considering the effect of leakage. The practice of belt segregation is concerned with the potential for fires in the belt roadway although there are numerous other potential fire sources in underground coal mines. A review of segregation practices has been conducted applying ventilation engineering principles. Four different scenarios have been analysed with regard to the effectiveness of the segregation stoppings in preventing potential fire contaminants migrating to other parts of the mine. The results show that in some cases the benefits of segregation to a person evacuating a mine in the event of a fire range from beneficial to detrimental. This is influenced by many factors including the location of that individual in that particular mine. There is room for improvement in the design and implementation of escapeways in underground coal mines. Escapeways need to be planned and designated with regard to the potential sources of fire, pressure differentials between escapeways and the operational practicalities of maintaining the pressure differential between them.CITATION:Olsen, M, 2013. Belt road segregation and escapeways - Compliance or risk management?, in Proceedings The Australian Mine Ventilation Conference, pp 311-318 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013

By H. Colijn

Belt scales are frequently used in the mining industry because of the ability to handle large tonnages without interrupting the material flow, fitting easily into all types of bulk handling systems and being relatively inexpensive. Although manufacturers claim weighing accuracies better than Y2%, many operators experience, in practice, much larger errors and they have become apprehensive about the use of belt scales. However, in spite of these disappointing instances, a belt scale is one of the most valuable tools for process and inventory control. Since it is a measuring device, care should be given to the design and installation of belt scales. The basic components of a belt scale are: (1) conveyor belt, (2) scale suspension, (3) sensing device, (4) integrating and recording. The first component of this system is of great importance to the overall accuracy and has been thoroughly discussed in earlier papers. This paper will review primarily the various scale hardware designs currently available, and will be confined to the last three components of the system.

Jan 1, 1973

By Jon P. Thorson, James W. Babcock

The second Belt Symposium in Missoula, MT, Oct. 9-16, 1983, was designed by its conveners as a field conference on progress in the Proterozoic Belt Supergroup rocks. The symposium was sponsored by the University of Montana with corporate support by Anaconda Minerals. Asarco Inc., Exxon Minerals Co.. Hecla Mining Co., Molycorp Inc., Noranda Exploration Co., and Utah International Inc. Introduction The Belt Supergroup is a thick middle Proterozoic sedimentary sequence deposited in a basin along the edge of the North American craton. Subsequent geological events have modified the basin so its remaining rocks outcrop in Montana, Idaho, northeast Washington, southeast British Columbia, and southwest Alberta. The Canadian equivalent of the Belt is called the Purcell Supergroup. Several similar age basins occurred along the western edge of the Proterozoic North American craton. The sedimentary sequence in the Belt basin aggregates is more than 18 km (60,000 ft) in the thickest section, where the bottom is still unexposed and the top removed by erosion. The limits of the Belt basin are poorly known because of later sedimentation and tectonic disruption. Knowledge about the Belt terrane has been difficult and tedious to obtain because the rocks are generally monotonous and fine-grained. During the last decade, new 1:250,000 scale reconnaissance maps of most of the Proterozoic Belt terrane were published, open-filed or otherwise brought close to completion. These maps provided the opportunity and challenge to consider the stratigraphy and tectonics of the Belt Supergroup as a complete basin. This broader view has contributed greatly to the solution of numerous geological problems created by previous, more focused work. Along with the availability of better geological base, there have been new exploration developments. The 1973-1983 decade saw proof of the commercial viability of the Cu-Ag mineralization at the Troy mine. The conclusion was also accepted that the Sullivan mine was a sedimentary massive sulfide. So was the conclusion that the Cu-Co mineralization at the Blackbird mine at Cobalt, ID, was the result of similar submarine exhalative processes. And there were discoveries of another Cu-Ag deposit "larger and higher grade" than the Troy mine and of two new massive sulfide districts. The Belt-Purcell terrane has long intrigued exploration and mining geologists as the host of Pb-Zn-Ag veins of Idaho's Coeur d'Alene district and of the Sullivan mine at Kimberley, British Columbia, one of the largest Pb-Zn-Ag deposits in North America. In the mid-1960s, Bear Creek Mining Co.'s discoveries of the stratabound copper-silver occurrences in the Revett Formation brought new interest in the basin's geology. The recognition of the Sullivan ore body as a sediment-hosted massive sulfide has also generated minerals exploration activity in the US portion of the Belt basin. This activity increased again after the Australian discovery of the world class Olympic Dam deposit at Roxby Downs, South Australia. This occurred because of some suggested similarities in the regional geologic setting of the Belt basin with the Adelaide geosyncline, the host for the Olympic Dam deposit. Technical Sessions Technical sessions topics included Lower Belt and Ravalli Group stratigraphy, Middle Belt carbonate and Missoula Group stratigraphy, Belt-Purcell stratigraphy, structure and tectonics, strata-related mineral resources, geochronology and geophysics, geochemistry and isotope geology, and a summary of significant problems. Evening poster sessions dealt with the topics and papers presented each day. Since the first Belt Symposium, mapping of the stratigraphic units and their tectonic setting has enabled geologists to progress in conducting a basin analysis. Belt Symposium II revealed no concensus on many aspects of belt geology. However, basic stratigraphic studies have reached the point that models can be constructed. The Prichard Formation is equivalent to the Aldridge Formation, but detailed correlations were not previously available. Studies were made by Finch and Baldwin (Cominco American) and by Cressman (US Geological Survey). These studies established important correlations of key markers within the Aldridge Formation to units in the Prichard Formation. This will help eliminate geologic interpretation problems at the US-Canada frontier and make Belt basin reconstruction more accurate. Also, the Sullivan ore deposit was shown to be formed in the deeper distal part of the basin. This contrasts to the more proximal depositional position of the Prichard Formation. Hamilton

Jan 6, 1984

By R. T. Swinderman

This paper discusses a series of tests designed to help answer the age old question: ?How much does the belt cleaner wear my belt?? The experimental set up and test method are described. The main variables are: belt cleaner blade materials, cleaning pressures, cleaning angles, belt speeds, and belt top cover grade. The bulk material used is a standard test-grade silica sand. The measured results include: blade mass loss, belt mass loss, and cleaning efficiency.

Jan 1, 2010

By H. Colijn

Weight may be defined as the gravitational attraction or earthpull on a body (mass). Thus, from a practical viewpoint, a scale or other form of weighing device is a mans for determining mss. Weighing devices fall into two principal categories: (1) gravimetric; and (2) non-gravimetric or nuclear devices. At present, after many centuries of use, the effect of gravitational force as a meas¬ure of mass in industry and commerce remains by far the most common method for mass (weight) determination. Non-gravimetric methods are just becoming established in the industry. The general trend is toward weighing materials on the Trove. The predominant advantage of continous weighing over batch weighing operations is its ability to handle large tonnages without interrupting the material flow. The accuracy and reliability ability of continuous weighing equipment have improved greatly over the past decade. However, static weighing equipment still outsells continuous weighing equipment, because it is considered more accurate. Batch weighing can also produce a continuous weighed delivery through automation where the process requires it. In caparison with continuous weighing devices, such as belt scales, the batch-type scales have same inherent advantages affecting their accuracy. For example, weighing 300 lbs. per minute on a belt scale may mean that only 3 lbs. will be on the scale mechanism at one time. In order to obtain a scale accuracy of 1/2%, the sensitivity must be at least 1/2% of 3 lbs. or 1/4 oz. On the other hand, a batch scale may discharge a 300 lbs. load every 60 seconds through a timing mechanism. An accuracy of 1/2% can be easily obtained with a sensitivity of 1/2% of 300 lbs. or 24-oz.

Jan 1, 1970

By C. A. Wiggins, J. M. Kennedy

The Benbrook Connection tunnel forms approximately 6,666 m (19,560 ft) of17,678 m (58,000 ft) of raw water pipeline connecting Lake Benbrook with the Rolling Hills Water Treatment Plant. This connection is designed to minimize costs to the owners, the Tarrant Regional Water District, for providing raw water to its’ various clients. The geological formations through which the tunnel passes and the design requirements resulted in some-what unique applications of initial ground support systems which were modified by the con-tractor to optimize the mining operations. The pipe sections, fabricated in 12 m (40 ft) sections, are concrete lined and coated steel pipe. Construction of the work shaft and tail tunnel was also modified to suit the contractors methods. A Lovat universal TBM was chosen to excavate through the various rock types. The pipe sections will be transported using beam carriers.

Jan 1, 1997

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

By P. D. R. Maltby

This paper describes the background and markets for calcium carbonate and silica sand in Canada, as well as the results of recent test work carried out at the Ontario Research Foundation. Tests on sericite, tremolite, vermiculite, barite and graphite are also mentioned.

Jan 1, 1979

By I. R. Firth, D. L. Taylor

The ability to accurately model the movement of grade boundaries during a typical bench blast would be of significant benefit to mine operators. The movement of grade boundaries during the blasting process may have significant impact on grade recovery if not accounted for. The paper describes the preliminary stages of a research project which combines numerical blast models and conventional mine planning software to allow practical use of the results of a numerical blast simulation. A two dimensional bench blast is simulated using the Universal Distinct Element Code (UDEC). The results of the simulation are used to provide input to the Surpac mine planning package which can be used to generate grade control plans.

Jan 1, 2001