Search Documents

By G. E. Karantzavelos

Introduction Pure alunite (KAl3 (SO4 )3 (OH)6 ) contains 37% A1203. In the alunite ore found on Milos Island, Greece, opal is the principal gangue while some aluminum, iron, and titanium oxides are also present. Processing of alunite ore leads to the recovery of potassium sulfate, alusil (alumina-silica mixture), and sulfur dioxide. An interesting process has been developed in Greece (Svoronos, 1977) consisting mainly of roasting the alunite ore mixed with KCl to disrupt the mineral lattice in preparation for separating its components. The thermal decomposition of alunite at approximately 600°C occurs by the reaction: KAl3 (SO4)3 (OH)6 + nSiO2 + 6KC1 - 4 K2SO4 + 3 A1203 . nSiO2 + 6 HCl + 3H20 According to the process pure alunite mixed with 543 kg KCl, 840 kg K2SO4, 370 kg alusil, 264 kg HCl, and 65 kg H2O are produced. The roasted calcine is leached in hot water. The potassium sulfate leach slurry is then thickened and washed to obtain a solid residue (alusil) plus a solution rich in potassium sulfate. Assuming the alunite ore feed consists of 50% to 60% alunite, the solid residue might consist of approximately 22% to 27% A1203, silica, iron, and titanium oxides. This leach residue could be digested in a hot sodium hydroxide solution to dissolve alumina. An amount of the alumina (approximately 10%) would not dissolve. In addition, part of the silica would dissolve requiring removal from the solution in a subsequent desilication operation. The same leach residue could be attacked by mineral acids such as a diluted hydrochloric acid to extract aluminum chloride (Sawyer et al., 1983). Alumina and aluminum are presently produced from bauxite of which Greece has important reserves. If this aluminous material (alusil) could be beneficiated by any physical process, then it would be considered as a raw material for the production of fire-clay refractories instead of an alternate source of alumina. Experimental procedure Extensive laboratory work (mineralogical and chemical analyses) indicates that alusil is a mixture of liberated (mostly) alumina and silica particles, not a natural silicate mineral. Table 1 shows the chemical assays of two alusil samples that were obtained from a roasted alunite ore leaching pilot plant. The samples used for the experiments were a very fine alusil powder (K80 = 400 mesh, 38 µm). These were pulped in tap water. Desliming of the pulp before each flotation test was ineffective. Flotation tests were performed in a 2000 ml Denver cell. A standard 500-g sample was first conditioned at a pulp density 50% solids for 5 min with hydrofluoric (HF) acid solution (40%). The temperature of the conditioned pulp was measured and kept nearly constant at 50°C. The pH of the conditioned pulp was also regulated to 2.5-3 with HF solution. Then ARMAC C solution (2%) as well as two drops of fuel oil and one drop of AEROFROTH 65 were added and the pulp was reconditioned for 2 min. After conditioning, the viscous pulp was transfered to the flotation cell. It was then diluted with warm water to about 15% solids and floated to separate silica from alumina particles. A rougher froth product that was cleaned and recleaned was obtained from the flotation tests.

Jan 1, 1987

By R. G. O’Meara, S. M. Runke

THE Bureau of Mines has been charged by Congress to investigate processes for the production of alumina from low-grade bauxite, alunite, and clay. As one part of the program, an investigation of the application of ore-dressing methods to improve the grade of high-silica bauxite is in progress at the Mississippi Valley Experiment Station at Rolla, Mo. This paper summarizes data obtained so far and presents detailed results of tests on four typical samples. MINERALOGY OF BAUXITE The name bauxite originally was used to designate the dihydrous aluminum oxide (A1203.2H20). The designation has been retained, although the existence of a specific mineral of such composition has been disproved. The term is now applied to ores of aluminum consisting of various mixtures of the minerals gibbsite (A1203.3H20), diaspore (A1203.H20), and boehmite (A1203.H20). The predominant hydrous aluminum oxide in most American bauxite, however, is gibbsite. In some instances bauxite may be amorphous mixtures of the hydrous aluminum oxides that approximate the composition of dihydrous aluminum oxide (A1203.2H20). The proposed name for this material is cliachite. Gibbsite and boehmite, the trihydrate and monohydrate, are soluble in a solution of sodium hydroxide at elevated temperature and pressure, whereas diaspore is practically insoluble. The solubility of these two minerals is the basis of the Bayer process of alumina extraction. All bauxites contain certain impurities, the commonest of which, in the order of their importance, are: silica, principally as a constituent of kaolinite, and to a lesser extent as quartz; iron, as hematite, limonite, and siderite; and titanium, as ilmenite, rutile and leucoxene. Minor impurities are zircon, cobalt and nickel. Bauxite is produced commercially in Arkansas, Alabama, Mississippi, Georgia and Tennessee, but the most important deposits in the United States are in Arkansas, in the vicinity of Little Rock. HISTORY OF BAUXITE BENEFICIATION The literature on bauxite beneficiation is limited, but the reports of Gandrud and DeVaney1 and Clemmer, Clemmons, and Stacy2 show the possibilities of flotation as a means of beneficiating bauxite. Their work has also developed reagent

Jan 1, 1944

By C. Ek

Tailings originating from the gravity concentration of a gold ore containing about 14 g/t Au have been treated by various beneficiation methods. These tailings have been screened on the 147 and 74 micron sieves and the two coarsest fractions have been separated on shaking tables with unsatisfactory results, but the concentrates have been examined in polished sections for mineragraphic analysis. Very simple flotation flowsheets have been applied to collect most of the gold, recovery and grade varying with the regrinding time in a ball mill. Cyanidation tests have shown that this type of treatment is also applicable to such tailings.

Jan 1, 1991

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By P. R. A. Andrews, R. K. Collings

The beneficiation of barite has been the subject of many investigations at CANMET, thus reflecting barite's importance as an industrial mineral. Fifty-one studies relating to various aspects of beneficiation were conducted between 1920 and 1986, and a review of some of the more important studies is presented. The information, including mineralogy, beneficiation methods and results, flotation parameters, and reagent concentration data, is presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of barite ores from a variety of origins.

Jan 1, 1990

By J. Iannicelli

A variety of domestic bauxites have been beneficiated to meet refractory grade standards by use of high intensity, high gradient, wet magnetic separation. Besides reducing the iron content to less than 2%, the Ti02 content of the bauxite was also reduced. The beneficiation can be accomplished by means of a simplified wet process flow sheet with an estimated cost comparable to that of water washed, filler grade kaolin. The process has been carried out on a small pilot plant and then scaled to produce 25 tonnes of calcined refractory bauxite meeting National Stockpile Specifications.

Jan 1, 1984

By Downing Terry L.

Dry mineral beneficiation methods have been developed for separation of borate minerals from montmorillonite claystone gangue. The methods include the use of newly developed dry high intensity magnetic separators. The application of these methods has the potential for economic benefit at U.S. Borax Inc. in three areas: ? Processing surface impoundments (ponds) material. ? Pre concentrating ore to be fed to primary refinery. ? Concentrating borate minerals to produce potential products.

Jan 1, 1995

By S. C. A. Franca, M. T. Millqvist, A. B. Luz

Laboratory experiments were performed on a Brazilian diatomite from Bahia State to produce an industrial product for use as a filter aid. Bench and pilot plant tests were conducted consisting of: diatomite desegregation, organic matter and clay removal, filtration, drying and calcination. Calcination temperature and sodium carbonate addition influenced diatomite particle size distribution. Optimum filtration rates for calcined products were obtained at 900°C and 47 min. residence time with 3% (w/w) of sodium carbonate addition, and resultant products met specifications imposed on filter aids.

Jan 1, 2002

By P. R. A. Andrews

Magnesite, brucite and dolomite occur widely throughout Canada, but deposits of economic significance are found only in Quebec, Ontario and British Columbia. Magnesite occurs in all three provinces, brucite in Quebec and Ontario and dolomite in Ontario. Beneficiation of refractory magnesium minerals has been the subject of many investigations at CANMET and the former Mines Branch. Twenty-three magnesite, four brucite and nine dolomite evaluation studies were conducted between 1920 and 1974. A review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and flotation data.

Jan 1, 1995

By R. F. Al-Fariss

The phosphoric acid industry is expected to develop in Saudi Arabia in the near future. There are three main reasons for expecting this: the discovery of phosphate deposits in the Sirhan-Turayf region, the construction of phosphate fertilizer facilities of the TSP, DAP and NPK plants on the east coast of the country, and the availability of an ample amount of sulfur As a by-product from the petrochemical industries. This study is a part of the research work performed in the chemical engineering department At King Saud University to evaluate the Saudi phosphate rocks for the wet process phosphoric Acid production and to test different flotation methods for the carbonate rich phosphate rock In a laboratory scale flotation cell. Experimental results for the above tests, as well as Beneficiation by calcination, are presented.

Jan 1, 1993

By D. P. Chakraborty

Joda East Iron Mine, one of the captive iron ore sources of Tata steel, located in the state of Odisha in eastern India caters to approximately 45% of the iron ore requirement of the Jamshedpur Steel Plant. The iron ore occurring in the mine having high in iron content along with high in alumina. Clay and gibbsite are the predominant mineral phases present as surface coating, fracture filling and/or free occurring and are responsible for alumina content higher. Alumina in iron ore impacts the techno-economic performance of a steel plant by impacting sintering and blast furnace productivity. The impact is even higher when it comes to fine ore used in the blast furnaces in the form of sinter as it constitutes a major portion of the blast furnace burden. Therefore, it is beneficial to upgrade iron ore in the mine head and to reduce alumina before it is subjected to agglomeration. Mineralogical test works reveal, that alumina in iron fines is mainly associated with the clay attached to the hematite particles, either free or interlocked to a very fine size. The paper describes the efforts made to reduce alumina in the iron fines in Joda East processing plant, without much of capital investment for a very sophisticated fines beneficiation circuit. In this process, a suitable dispersant was added in the plant that dispersed the masked slime coating over the iron ore fines, thereby making a better quality iron ore fines with reduced alumina content. The alumina in fines improved by 0.2 units? means from a label of 2.4-2.6 % reduced to 2.2-2.4 %. With this initiative, not only the primary objective of alumina reduction is met but also it has given substantial benefit in reduction of silica and as well as moisture in product. This moisture reduction also has given bottom line impact by reducing idle freight and royalty.

Sep 1, 2012

By Surendra Kumar Biswal, Sachida Nanda Sahu, B. C. Meikap

The unutilized iron ore fines (IOF, − 10 mm, 45% to < 60% Fe(T)) left at various mine sites during blasting and processing are rich in goethetic-hematite associated with high clay and considered a potential iron ore resource. The variation of loss on ignition (LOI) from mines to mines is based on the goethite and clay mineral content. The clay containing below 45 μm is mostly brittle, causing beneficiation problems. The IOF has an LOI of 7.83%, with high silica (5.52%) and alumina (4.57%), and 57.17% of Fe(T) subjected to both conventional deep beneficiation (CDB) and magnetization roasting using high-ash non-coking coal to adopt the suitable upgradation process. The CDB and magnetization roasting concentrate has 62.61% and 67.58% Fe(T) with 64.69% and 85.19% yield, respectively. However, the presence of 6.40% LOI in CDB makes the ore challenging for pelletization. Characterization like X-ray diffraction(XRD), scanning electron microscope(SEM), and chemical analysis was used to assess the concentrate quality and potential industrial application.

Jun 4, 2022

Beneficiation of Coal Fines from Tailing Ponds of Tuntbilek Washing Plant

Sep 13, 2010

By Jing Zhou

In view of the state of the long time use of sodium cyanide in lead-zinc-sulfur-silver multimetallic ore production, we propose alternative reagents system through experimental research. The experiment first used TJ, sodium sulfide to adjust the flotation pulp, after that, zinc sulfate, sodium sulfite was added to low alkaline pulp to inhibiting zinc sulfur mineral and adapted MB, 25# aerofloat and diethyl dithiocarbamate combination collectors to float lead minerals. The obtained test index is as follows: lead concentrate recovery rate of small scale test was increased by 5 to 10%, the recovery rates of gold and silver in lead concentrate were increased by 7% and 11% respectively; the industrial test is conducted under the condition that the total grade of lead and zinc content in raw ore decreased by 4.81%, the total recovery rate of lead and zinc increased by 7%, recovery rates of gold and silver in lead concentrate were increased by 7.62% and 9.65% respectively. So it successfully realizes the target to replace the sodium cyanide, using low-alkaline non-toxic reagents system in mineral processing practice of three kinds of complex lead-zinc-sulfur ore of this mine. Keywords: refractory lead-zinc-sulfur ore, depressant, non-cyanide flotation

Sep 1, 2012

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By F. Bourgeois, J. -S. Kroll-Rabotin

ABSTRACT: Falcon concentrators are enhanced gravity separators designed for concentrating fine particles. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidization water. We investigated the physics of particle transport inside Falcon concentrators, and concluded that separation efficiency is governed by differential settling velocity. We derived and published a predictive model of the partition function under dilute conditions. We intend to extend the initial model to concentrated ultrafine suspensions for application to industrial scenarios by adding hindered settling to account for solid concentration effects.

Jan 1, 2011

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By U. S. Chattopadhyay

The estimated requirement of the nation by the year 2020 is approx. 80 Mt of steel and more than 0.2 million MW installed capacity of the electricity, thereby increasing the consumption of the coking and non-coking coal, which is expected to be in tune of about 75 Mt & 500 Mt respectively. One of the major deleterious factors in achieving the goal is the deteriorating quality of the feed coal used in both steel and power industries. Indian coking coals, in general, are typified by high ash, high inert (both organic and inorganic), low rank, low reactive macerals content, heterogeneous petrographic make-up, inferior coking properties and poor amenability to washing, thereby necessitating suitable washing measure. Coke-based steel industries in India require washed coking coal containing ash % varying between 17-19. The situation demands taking on immediate challenges to fill up the gap between the requirements and supply of coking coal. This paper reviews the R&D attempts in this laboratory and throws light on the key measures as long-term solution to the problem. Search for alternative source of coking coal, like LVC coal and their judicious preparation technology. The low volatile coking coal (LVCC) constitutes about 50% of the total coking coal reserves in India. These coals are characterized by high raw coal ash content (37 to 40%) and very difficult washability potential. If these coals are treated in the existing washeries, which are generally 2 or 3-product systems, the cost of clean coal is high as the byproduct sale value is low. It has been proposed to produce a new type of by product, which enjoys high demand and good coking properties.

Sep 1, 2012

By S. S. Hsieh

Bench-scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process employed diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used; one contained 21% P205 and 3.2% MgO, and the other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31-33% P205 and 1% or less MgO can be obtained, with P205 recovery of about 80%.

Jan 1, 1984

By S. S. Hsieh, J. R. Lehr

Bench scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process used diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used. One contained 21% P205 and 3.2% MgO. The other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31% to 33% P205 and 1% or less MgO can be obtained, with about 80% P205 recovery.

Jan 1, 1986