Search Documents

By N L. Thomas

Hole size affects many factors which directly influence fragmentation in the muckpile and hence, the cost effectiveness of the entire operation. These factors include production capability, explosives and accessories efficiency and usage and drilling accuracy. In addition, hole size should be chosen to suit the geological conditions. The paper concludes that the optimum hole size is generally the largest that can be used commensurate with production and environmental considerations.

Jan 1, 1986

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By S S. Kanchibotla, S Morrell

In recent years there has been a growing recognition of the impact that mining practices have on the efficiency of mineral processing operations. Head grade, dilution, particle size distribution and their variability are known to have a significant effect on the throughput and recovery achieved in mineral processing plants. Improved process monitoring and modelling have provided the opportunity to identify and quantify some of these impacts and to define very significant incentives to optimise the overall operation from the mining face through subsequent comminution and processing. The Julius Kruttschnitt Mineral Research Centre has been undertaking research to optimise æMine to MillÆ performance through a major AMIRA research project and through individual research contracts with mining companies. This work has resulted in a broad range of field and laboratory experience in terms of both the challenges and the opportunities encountered when tailoring blasting operations to suit the overall æMine to MillÆ production chain. This paper describes the objectives of æMine to MillÆ blasting to optimise the system of rock breakage involved in the blasting, crushing and SAG milling of hard, brittle ores. The design of such blasts falls outside the conventional envelope of experience for most engineers and requires the consideration of some critical factors if the objectives of such blast are to be met and some of the potential problems are to be avoided. Experience to-date has also found that the quality of implementation is critical to the success of æMine to MillÆ blasts.

Jan 1, 1999

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998

By John Norman

This paper will cover blasting techniques that are applicable to underground and other rescue that involves removing obstacles and breaking rock in close proximity to rescuers and subjects.

Feb 1, 2020

By Jay Smerekanicz, Florin: Pedersen Gheorghiu, Alan Cameron

In order to expand the capacity of Modern Landtill, a groundwater extraction system consisting of a linear system of pumping wells over 2,700 feet long had to be replaced. The new system would be covered by landtill cells to a depth of approximately 400 feet, and therefore would have to be maintenance free. In addition, the new system had to be proven to be more effective than the previous system, groundwater extraction had to be maintained during construction and construction could not disturb either the landfill operation or nearby residential neighbors.

Jan 1, 2001

By James E. Jr Hargroves

With the ever-increasing population growth and modern trend to urban development, the expansion of utilities is a stable, mad or, and constant source of income for many. Blasting is a "necessary evil" to the utility contractor. It can make or break even the most solvent. Housing development expansion and higher treatment of effluents are causing utilities to appear in more congested areas. This paper discusses some of the aspects of utility blasting in the State of Virginia. Consideration is given to bid procedures, pre-blast surveys, record-keeping and practical application.

Jan 1, 1977

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Blasting is a common practice in mining whereby solid rock is fractured, using explosives, to a more manageable size. The effectiveness of blasting influences a number of downstream activities such as shovel digability, crusher throughput and mill throughput. As the cost of explosives is relatively low compared to milling costs (mainly due to power consumption), blasting practices can be optimised so that the downstream processes are made more efficient, and an overall cost saving made. This is the basis of the Mine to Mill approach. The effectiveness of the blasting is influenced by two main factors, the blasting practices used (eg explosive amount and type) and the geology of the area. As the geology cannot be altered, the blasting practices must be refined to create optimum blasting. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation, located in the heart of the Kalgoorlie Goldfields is the largest gold mine in Australia. Mine to Mill at KCGM has had varied success, with initial positive indications being lessened by a number of factors, including the increase in the amount of voids.

Jan 1, 2003

By Alain Blanchier, Anne Charline Sauvage

Rock mass variations have a huge influence on explosives efficiency and on blasting results. Numerous blasting improvements could be gained by taking into account rock mass and its variations. However, extracted rock mass is generally considered as statistically homogenous. The development of a panel of pre-blast survey procedures that every blaster can use, consists in the realization of a process integrated into every day work: for example as well as toe burden or blast hole depth, discontinuities spacing or the weathering expanse have to enter in rule book, if it provides blasting efficiency and security improvements.

Jan 1, 2004

By Ray Patterson

A planned modification to a cement kiln at the Holnam Portland Cement Plant near Florence, Colorado required the removal of a ring of cast-in-place (CIP) refractory lining. The CIP lining was approximately 14 inches wide, 12 inches thick and 38 feet in circumference.

Jan 1, 1999

By Moore A. J

Blasting in mines in an urban environment can be conducted safely and within regulatory vibration limits by careful attention to detail and the application of correct techniques. Factors affecting blast vibration are described using surface and underground mining examples. An understanding of these factors provides an essential base for effective planning and operational control. Techniques are described for assessing and predicting vibration levels and the presentation of data for planning purposes such as environmental impact statements for new projects and the protection of buffer zones around existing operations.

Jan 1, 1997

By Charlie Brumbaugh

Antarctica with its diverse conditions such as severe cold, high winds, rock and ice structure and limited explosives available posed many obstacles. This paper will give an overall view of the methods used to overcome these obstacles on a daily basis on the highest, driest, coldest continent on earth.

Jan 1, 2000

By Richard Goodridge, Stephen Thomsqn, S Rodgers, D Tunaley

The mining, quarry and construction industries are facing’new challenges everyday. These challenges can be imposed by economic objectives or through external factors such as extreme geological conditions. Simultaneously, all mines, quarries and construction sites are facing more and more stringent environmental requirements.

Jan 1, 1998

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015