Search Documents

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By G. A. Savanick

Borehole (slurry) mining, where a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a US Bureau of Mines program to increase the domestic availability of critical minerals. About 1.5 kt (1700 st) of phosphate ore were mined at 23.6 t/h (26 stph) from a depth of 76 m (250 ft). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1986

By Gregory Abramov

Borehole Mining (BHM), a remotely-operated waterjet mining method (Figure 1), has recently achieved two major milestones. It was, for the first time, applied to the extraction of manganese ore and at temperatures below freezing. The 1St stage is a demonstration test that is now underway just north of Emily, Minnesota, where the manganese ore is located 100-160m below the surface and its reserves are estimated to be in excess of 500,000 tons. The deposit was discovered over 60 years ago but, due to the fragile and sensitive nature of this Land of 10,000 Lakes (nickname for the State of Minnesota) and strong environmental restrictions, the iron/manganese reserves were deemed unrecoverable and remained untouched until late 2010 when permission for a single-hole demo-test was issued by the local Department of Natural Resources.

Jan 1, 2011

Develop an environmentally feasible method of mining shallow oil sands without removing overburden. Approach Oil sands are extracted through a single borehole by cutting into the sands around the borehole with a high pressure water jet, and pumping the resulting slurry to the surface. Although oil can be extracted from shallow fields by open-pit mining methods, this type of mining may create significant environmental impacts, including; (1) disruption of the surface, (2) accumulation of waste rock piles, (3) accumulation of tailings, (4) damage to the ground water quality, and (5) surface water pollution. The borehole mining system developed and successfully field tested by the Bureau of Mines offers a method for extracting oil from oil sand with minimal disturbance to environmental quality. (For examples of other applications of borehole mining, see Technology News Nos. 95, 63 56, and 48.) How It Works Prior to the start of mining operations, baseline conditions for ground subsidence and ground water quality are established at the test site so that the degree of subsidence and changes in ground water quality can later be determined. Oil sands mining is conducted using the Bureau of Mines borehole mining system. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three passage swivel terminated with a mining section. The mining section has an auger at the bottom. Four slurry inlet holes and an eductor are located above the auger, and a single cutting nozzle is located near the top of the mining section. The tool generates a high velocity water jet that erodes and slurrifies ores. The slurry is drawn into the inlet of the eductor which lifts the slurry to the surface where it is deposited into a slurry discharge sump. To detect evidence of subsidence, surveys of the land surface are made at regular intervals during, and until 30 days after, the termination of the mining operations. Samples of ground water from the borehole and two adjacent monitor holes are taken on alternate days during the mining operations, and are later analyzed to determine if any ground water contamination has occurred.

Jan 1, 1981

By M. F. Dibble

The technology available for mining of underwater mineral resources such as placers and phosphorite, typically occurring with variable amounts of overburden, has remained largely unchanged for decades. The traditional bucket ladder dredge with maximum digging depth of 48 m and monthly capacities about 500,000 m3 still reins as the only heavy duty mining system capable of working the tough materials characteristic of heavy metal placers. Attempts at adapting the bucket wheel cutter-suction dredge to these severe conditions have not yet been successful except in moving small volumes from shallow depths. High capital cost (20-30 million U.S. dollars), high cost of overburden removable, and turbidity generation for the bucket ladder are often significant negative factors in mining operations where this system remains the only viable alternative. The Japanese continue to advance the technology of their submersible dredge pump system powered by specially adapted, direct drive electric motors. Present systems are designed primarily for working surficial deposits of aggregate to depths as great as 90 meters, the pump suspended by cable from a surface vessel with an eductor pipe leading from the pump to the vessel. Such a system may prove adaptable to a variety of surficial deposits including phosphorite, shell and heavy minerals in addition to aggregate. However promising for the exploitation of surficial deposits, little advantage can be expected for the deeper buried and more difficult deposits.

Jan 1, 1986

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

By M. F. Dibble

Borehole mining, as a viable concept for recovering deep sedimentary mineral resources, historically has been long on promise but short on results. Application of the technology seems best suited for recovery of Miocene phosphate resources on the East Coast of the US. These deposits are potentially enormous in scope and underlie sections of the coastal plain and the near offshore continental shelf. The landside portion of these deposits is generally too deep to mine using conventional open pit methods. Recovery of these minerals requires development of alternative mining systems. A significant proportion of the offshore resources appear to occur at depths below the practical limits of cutter suction dredges and may even exceed the limits of bucket ladder dredges. In most cases, these deposits are covered by overburden that must he removed and redeposited before the mineral section can be mined. The depth, thickness, composition of overburden and environmental sensitivity of a particular location would greatly impact mining system selection. It is probable that dredging would not be an environmentally acceptable mining method in many of the areas underlain by this phosphate rock. In cases such as these, new processes such as borehole mining must be evolved or the resource will remain undeveloped. A borehole mining test program, using an existing prototype borehole system, successfully extracted Miocene phosphate in northeast Florida in 1984-1985. The top of the main mineral zone was 80 m (261 ft) below the surface. Based on the results of this test program. plus subsequent laboratory testing and engineering studies, a new prototype borehole mining system was designed in 1986. This design incorporated several innovations of offering potentially higher productivity and lower power consumption than was achieved with the previous test unit. Economic restraints at that tine prevented the actual construction and testing of this new design.

Jan 1, 1992

Provide a means for reliable in situ stress change measurements in soft, friable geologic materials under high stress. Background Effective mine design requires a knowledge of changes in rock stress generated by a mining operation. In situ stress measurement can provide a means of obtaining this knowledge from an active mine for the ultimate purpose of design verification and analysis. The Bureau of Mines has designed and tested a device for measuring changes in rock stress-the borehole platened flatjack (BPF). It has found application in investigating stress anomalies due to geologic structures, stress concentrations from multiple seam interaction, and stress abutments from pillar retreat and longwall mining.

Jan 1, 1990

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By G. G. Marino, Z. R. Widup

Marino Engineering Associates, Inc. (MEA) was asked to determine the effects of mining beneath a proposed roadway structure. In order to determine the subsidence potential and the magnitude of the mine stabilization costs it is important to know whether underground mining is present, and if so, to what a real extent. The site investigated had the potential to have mining in three different coal seams. To determine where mining was present MEAÕs borehole radar system was used. In summary, the borehole radar subsurface investigation validated that the available mine map in the most shallow coal seam was fairly accurate despite its age (1888), found no mining in the underlying coal seam and detected an area of unknown mining at a depth of about 300 ft in the lowest coal seam which was verified by subsequent drilling.

Jan 1, 2004

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By J. W. Merks

Spreadsheet software is used to convert test results for drill core samples into borehole statistics such as volumes and masses of in-situ ore, metal contents and variances of metal contents. The properties of variances and the sampling variogram play a pivotal role, The additive of property of variances gives a sound scientific basis to the calculation of confidence limits for metal contents and grades as a measure of the risks associated with estimating reserves and resources.

Jan 1, 2000

By Joseph A. Sohara, John J. Mullay, Curtis J. Keefer, Robert L. Schrepple

The desensitization of an explosive column by the action of a previous detonation (adjacent borehole, deck or detonating cord) is a vital concern to the explosives industry. Previous reports to this symposium and in other places have addressed this issue. However, this work has been mainly concerned with model or simulated conditions. No systematic study has appeared that utilizes an actual borehole environment. Thus the relation between this work and expected field performance is somewhat uncertain. The present paper attempts to partially resolve this difficulty.

Jan 1, 1990

By A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneuna.cic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 3000 cons per hour (2700 t(h) to the backfill level, situated about: 2000 feet (610 m) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1978

By V. Rajaram, H. W. Earnest, A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneumatic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 2700 t/h (3000 stph) to the backfill level, situated about 610 m (2000 ft) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This Paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1980

By Nicholas M. Short

Many a geologist or driller has wished he could somehow climb into a borehole to see for himself what fractures looked like. Or why recovery was poor. Or how the bit was actually lost. Now it is possible to do the next best thing to climbing into the hole. TV cameras are being used for a close-up look at borehole conditions. Ever since television was invented, geologists and others interested in subsurface conditions have wanted a TV camera that could be used in the narrow confines of a borehole. But development of such a camera was slow, mainly because of the need for compact size. Not until the late 1950's did the technology of electronic miniaturization develop to a point where a camera satisfactory for the purpose could be put together.

Jan 1, 1963

By Rixon LK, Walton KP

Evidence will be presented to show that borescope inspection of mine roofs is one of the most useful techniques available for stability assessments. ACIRL currently has four borescopes, comprising two fibre-optic units of 2.7 m and 4.5 m length and two optical rod units (introscopes) 6 m and 8 m in length. (The 8 m unit is not yet fully operational because of modifications needed to meet safety regulations). Using the fibre-optic units, photographs of hole walls or ends can be taken to record features. Roof lithology and crack patterns can be observed in roof holes from 25 - 60 mm in diameter. Several crack parameters are useful: type, location in the roof with respect to height and lithological boundaries, presence of individuals or zones containing crack clusters and the estimated amount of dilation. These data are readily computer- plotted to form "borescope logs". Provided that the holes remain open, a hole or group of holes can be re-surveyed at intervals to monitor crack development across or along a roadway, for example with respect to an advancing blind-ended roadway face.

Jan 1, 1986

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928