Search Documents

By Sean E. Armstrong, Deepak Malhotra

The current trend in gold ore processing is the development of lower grade or highly refractory deposits. The perplexity of treating low grade oxidized ores has been adequately addressed by heap leach technology. However, refractory gold ores are very difficult to positively characterize the gold association within the mineral matrix. Gold accompanied with refractory sulfitlc or carbonaceous mineralization can often be sub­micron In size and occur interstitially. Mineralogical examination of these ores Is difficult, expensive, and occasionally Inconclusive. Hence, the metallurgist Is given little information for the selection of processing alternatives. The purpose of this paper Is to demonstrate the use of diagnostic leach procedures to assist the metallurgist' s decision-making process to solve some of these problems. By sequentially liberating and/or leaching gold associated with specific minerals, the amount of recoverable gold in each stage can be determined. Through careful interpretation of the results obtained by diagnostic leaching, the metallurgist can devise a flowsheet for treating the ore or solve a problem at an existing plant

Jan 1, 1992

By M J. Daniel

The diamond industry is no newcomer to High Pressure Grinding Rolls (HPGR) as it has used the technology for more than 20 years, predominantly in secondary crushing and recrushing roles. In fact it could be argued that the diamond industry has led the way for the wider minerals industry to consider its application. In existing conventional secondary cone crushing applications, large valuable diamonds are" won" through meticulously managing the recovery process within defined particle size ranges. Conventional crushers operate with relatively large closed side settings, but have the potential to damage diamonds by making direct contact with the sides of the crusher. Cone crushers also result in steep product size distributions that run a high risk of losing many of the smaller, unliberated but more abundant diamonds from the rock. This current comminution paradigm of particle size reduction management results in recrushing processing applications or plants where HPGRs are often used.

Jan 1, 2010

By Paul C. Schmall

In recent years, several geotechnical methods have been successfully applied to ash pond closure. These include modified dewatering techniques with wellpoints and wells to physically drain the material, soil mixing to create a soil-concrete material for improved accessways as well as improved ground structures within ponds to act as barriers or gravity dams, and geotechnical instrumentation to serve as an early warning of the potential for liquefaction. Given the parallels between fly ash and sluiced in place mine tailings, the application of fly ash remediation method to mine tailings shows significant potential, as illustrated in this paper.

Feb 1, 2024

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp's Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

By A Golev, G Corder

The concept of the circular economy has been gaining traction both in Europe and China.In Europe the Ellen Macarthur Foundation see their mission as accelerating the transition from a linear take-make-dispose economic model to a circular model that is restorative and regenerative by design, and aims to keep products, components and materials at their highest utility and value at all times. The Chinese Circular Economy initiative is effectively a sustainable consumption and production program utilising cleaner production, industrial ecology and life cycle management approaches to meet the national challenges of maintaining rapid economic growth while simultaneously enhancing environmental quality and maintaining social progress. A key characteristic of both of these circular economy initiatives is to design out, reuse or minimise the generation of waste.The mining sector, by definition, is represented by linear rather than circular activities, by supplying resources to society. However, being one of the world’s largest waste generators, the sector can adopt similar logic to that of the circular economy to improve its sustainability performance. Waste is a critical issue along the whole metals value chain, from mining waste to eventual end-of-life products, such as scrap steel from construction and demolition waste or the growing problem of electronic waste.CITATION:Corder, G and Golev, A, 2016. Can mining be part of the circular economy or is it squaring the circle?, in Proceedings Life-of-Mine 2016 Conference , pp 121–123 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J. C. Miller

In offshore oil drilling as it is done today, accidental blowouts cause considerable damage lo the environment. Public alarm over such accidents has already resulted in a number of legislative proposals which appear to favor the cessation of all drilling on the Federally owned continental shelf. Present concern for the environment and the increasing water depths associated with offshore drilling suggest the desirability of applying underground mining technology to offshore petroleum exploration. If offshore drilling were to proceed from underground accesses to the continental shelf, accidental damage to surface waters would be avoided, and so would the difficulties of exploring in deep or ice-filled waters. The specific approach proposed here is intended as a preliminary to offshore oil exploration in a known field or geologic structure. The end result of this method would be an on-shore vertical or inclined shaft terminating in an operating tunnel or haulageway as shown in the illustrations. From the haulageway, branching access tunnels would lead to drilling compartments. With this arrangement, it appears likely that one operating tunnel could serve all lessees ill a particular unit operation. Although an inclined shaft is not illustrated, this would probably be more practical than a vertical shaft owing to the length of the casings and the character of other equipment used in oil producing operations.

Jan 1, 1971

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

By Robert G. Ditchburn

Dating seafloor mineralization at hydrothermal centres of submarine arc volcanoes is important for understanding deep-seated volcanic events that can produce deposits rich in base and precious metals. The activity ratios, 228Th/228Ra, 228Ra/226Ra (Bq.Bq-1) and 226Ra/Ba values (Bq.g-1) are used for dating barite- rich seafloor massive sulphide (SMS) in the age ranges 0.3 ? 12 years, 3 ? 35 years and 500 ? 15,000 years, respectively. Thus, the time elapsed to amass an economic deposit and, ultimately, its capacity for sustainable extraction, can be estimated. 226Ra/Ba and 228Ra/226Ra values have been measured in relatively young chimneys that were collected, 1998 to 2006, from hydrothermal sites at Brothers and Clark volcanoes (Kermadec arc) and East Diamante volcano (Mariana arc) to check these initial ratios, essential for calculating ages for older mineralization at the same sites, were not varying significantly. We found that the 226Ra/Ba value for fresh SMS mineralization at the Brothers NW caldera and East Diamante hydrothermal sites have been reasonably stable for 6 years and 2 years, respectively. At both sites, the 228Ra/226Ra value for fresh SMS has been stable for 5 years. This was established from young chimneys where the measured 228Ra/226Ra value could be corrected for radioactive decay using the age derived via the 228Th/228Ra method. However, long-term stability of the initial 226Ra/Ba and 228Ra/226Ra values has yet to be proven. These isotopes of Ra are used as a proxy for better understanding of the transfer of Ba from deep magmas to the seafloor, via the circulating fluids of the hydrothermal system.

Jan 1, 2011

By Fernando J. A. S. Barriga

"Recent concerns over the availability of many mineral raw materials, and newly available technological developments, produced renewed interest in deep-sea mining. However, environmental concerns, with variable degrees of justification, are raising opposition to the concept. The forecast for the behavior of consumption versus availability of many raw materials, nearly all critical metals, arguably show that consumption will grow much faster than resource discovery onshore. Finding new sources of raw materials seems inescapable. The deep seafloor stands out as the only likely candidate.Sea Floor Mining and the EcosystemMarine mining has already started, decades ago, for diamonds, currently up to depths near 400m. Although the industry recognizes there is a footprint, it considers the footprint quite minor, because the area mined is small: in Namibia, where offshore diamond mining is now 70% of the country’s total, only 3% of the concession of 3,700 sq miles (9600km2) have been mined. As plans to mine deep-sea massive sulphide deposits and polymetallic nodules progress, the environmental concerns grow. Some of these concerns are as follows:?The deep-sea ecosystems are composed of long-lived species, with low rates of reproduction. The environment may not recover from mining on a human time scale;"

Jan 1, 2017

By M Berner, N A. Sifferlinger, E Fimbinger

Today, the advance rate of underground roadway development by drill and blast operation is limited by the need to ventilate the toxic blast fumes after each cycle. In deep mines this usually is only possible during shift changes when the related mine sections are free of persons. This results in roadway development advance rates of 4 m per shift, or 12 m per day. For long roadways this is a limiting factor in mining development in deep mines. Companies like EPIROC, KOMATSU, ROBBINS and SANDVIK are making serious R&D efforts to disc-cutting mobile miners to overcome this bottleneck. However, today, the achieved advance rates are less than 12 m per day in hard rock. If we achieve full robotisation and/or teleoperation from a safe place for drill and blast operation of an underground roadway development section, we could eliminate this bottleneck. Poisonous blasting fumes do not affect robots and machines as long as these fumes do not create aggressive acids. If we can keep the blast fumes isolated in the roadway development section for the shift until the next ventilation opportunity (eg shift change or designated ventilation times), we can do the drill and blast cycle more often in a shift, which will significantly speed up the advance rate. This requires robotisation of all work steps in the section: surveying, drilling, charging of explosives, blasting, loading and transporting material, roof support, installation of infrastructure etc. Also, cache storage for the material is needed. Special care for the ventilation system to keep the blasting fumes under control in the section is necessary. The paper discusses the aspects needed to achieve this robotisation and the related technical and operational tasks.

Sep 1, 2024

By W. F. Boericke

WORLD production of silver in 1929 totaled 256 million ounces. In 1928 production was 258 million ounces, and in 1927, 254 million ounces. With an actual decrease in the amount of silver produced last year, as compared with 1928, and an increase over 1927 of less than one per cent, obviously there has been no overproduction of the metal in the popular sense. But the price of silver tells a different story. For 1927, the average quotation was 56.37 cents; it was 58.17 in 1928, and 53.0 in 1929. During the last year it reached a high point of 57 cents in January, and fell steadily, without interruption to the downward trend, to a low of 47 cents in December. Since then it has dropped to an all time low of 43 cents on February 6.

Jan 1, 1930

By R. Woods

"Comments on the paper ""Formation of hydrogen peroxide by chalcopyrite and its influence on flotation,""by A. Javadi Nooshabadi and K. Hanumantha Rao (Minerals & Metallurgical Processing, 2013, Vol. 30,No. 4, pp. 212-219)The formation of hydrogen peroxide from water during the grinding of chalcopyrite in a nitrogen-sparged environment, as reported by Javadi Nooshabadi and Rao (Minerals & Metallurgical Processing, 2013, Vol. 30, No. 4, pp. 212-219), is questioned on the grounds that oxidation of water by the mineral is unlikely to be thermodynamically feasible. It is argued that it is more likely that any peroxide that had been formed would have been generated from residual oxygen in the nitrogen-flushed system than from the oxidation of water.The formation of hydrogen peroxide by finely divided pyrite had been reported by a number of authors (Borda et al., 2001; Borda et al., 2003; Cohn et al., 2006; Schoonen et al., 2006; Schoonen et al., 2010; Jones et al., 2011; Javadi Nooshabadi et al., 2013). That hydrogen peroxide is formed in the presence of oxygen in solution can be comprehended from wellestablished mechanisms. Pyrite in aerated solution is known to oxidize by an anodic process that is coupled with the cathodic reduction of oxygen (Holmes and Crundwell, 2000). The latter process has been shown to occur through the formation of hydrogen peroxide (Biegler et al., 1975; Ahlberg and Broo, 1996). The pH dependence of cathodic oxygen reduction at other sulfide minerals, including chalcopyrite (Biegler et al., 1977; Rand, 1977), implies a similar mechanism at these surfaces."

Jan 1, 2015

By William Metcalf

IT is the object of this paper to oppose unnecessary changes, and the introduction of new and confusing terms. From the earliest times of which we have any record on the subject, iron has been divided into general classes. Whether iron was first known in the form of wrought iron or of steel, is a matter of no importance; but at the time when cast iron first became a prominent article of commerce, wrought iron and steel were old products¬steel, at that time, being generally made from wrought iron by the process of cementation. As steel was then properly defined as iron containing more carbon than wrought iron, so cast iron was appropriately defined as iron containing more carbon than steel. Until the year 1776, when Huntsman first began the manufacture of a new kind of iron by melting wrought iron and steel in crucibles, the above definitions were all that could be desired. At first, probably, owing to imperfect appliances, only a highly carburized iron was melted in crucibles, and this led to its being called cast steel. If our ancestors had found a name for this material not involving the use of the word steel, we would have been saved the trouble of the present discussion. As the arts developed, new uses were found for steel, and the products of the crucible were varied, until at the present day it is quite common to find steel containing no more carbon than average wrought iron, and other steel containing nearly or quite as much carbon as some cast iron. All of these various products of the crucible have retained, or received, the name cast steel, usually abbreviated to the simple word steel, without causing any confusion among producers or consumers in regard to terms or their meaning. In 1855, twenty-one years ago, the Bessemer process was introduced ; this was followed in a few years by the Siemens-Martin process, and the products of both were at once, and have ever since been, called steel, from the fact that they were identical in chemical and physical properties with crucible cast steel. At the present time, then, we have three subdivisions of cast steel, viz.: Crucible cast steel, Bessemer cast steel, and Siemens-Martin,

Jan 1, 1877

By G Corder

The aim of the circular economy is to accelerate the transition from a conventional linear take-make-dispose economic model to a circular model. It is restorative and regenerative by design and aims to keep products, components and materials at their highest utility and value at all times. This extended abstract presents a brief overview of the circular economy, provides application of the circular economy in other industrial sectors including the downstream metals value chain and proposes how circular economy thinking could progress the development of complex orebodies.CITATION: Corder, G, 2018. Can the concept of the circular economy help unlock complex orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 8–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R. D. Brown

In his April 10, 1978 budget address, Finance Minister Chretien declared that the federal government will restrict the growth of its spending to less than the trend growth of the gross national product; over the past year, both the federal and a number of provincial governments have taken action to cut back on spending policies. This new emphasis in restraint would seem 10 be a response to a mounting public reaction to the rapid growth of government spending - and taxation - over the past 25 years. Although this relatively new government posture on public spending may be admired by many, to others it raises the question: "Can the growth in government spending really be stopped?" This article comments on just how government revenues - and spending - have grown over the past few years in Canada, and mentions some of the issues relating to a slowdown in that growth.

Jan 1, 1978

By William Metcalf

ONE of the first questions that naturally occurs to one who handles steel is," Why does steel harden ?" To answer this question the chemist and physicist have devoted much thought and experiment, and while they have enriched our store of knowledge of the nature and composition of steel, it cannot be said that they have yet solved the problem involved in its hardening. In this communication I desire to direct attention to a line of investigation yet new, in the hope that it may receive the attention of those who have the time and ability to pursue it. I refer to magnetism. There are so many parallels between the action of magnetism on iron and steel and their behavior under different processes of manipulation that it would seem as if there must be some connection between the forces at work in the different cases, if, indeed, there be not an identity of force in all of these cases. Magnetism, as we know it, may be merely the visible manifestation of forces, which may serve as a guide to lead us to an exact knowledge of the structure, the strains, and the resistances with which we have to deal in iron and steel. If a magnet be brought close to a pile of iron filings, the little pieces of iron will fly to the magnet and attach themselves to it, with their longer axes lying in the direction of the force. If molten cast iron be poured into an iron mould,-a chill,-the iron upon crystallizing will form needlelike crystals, with their long axes normal to the surfaces of the mould. If the iron is at the proper temperature and the quantity small, compared to the mass of the mould, the whole of it will be chilled, or set, in' the hard needlelike crystals

Jan 1, 1881

By Paul C. Jones

Summitville is an old mining district located south of Wolf Creek Pass in the southern San Juan Mountains of Colorado at an elevation higher than 3500 m (11,500 ft). The Summitville mine site is about 40 km (25 miles) southwest of Del Norte. The current mine, developed by Galactic Resources Ltd. and its subsidiaries in the mid-1980s, is on the north facing side of South Mountain. The area is drained by Cropsy Creek to the east and Wightman Fork to the north, both tributaries to the Alamosa River. Mining in the Summitville area began in 1870 when James Wightman discovered placer gold on what is now known as Wightman Fork of the Alamosa River. The first vein-type deposits were located in 1873 on South Mountain near the current Summitville Mine. Mining began in the district in 1875 and continued sporadically through 1942. Major mining episodes occurred from 1875 to 1894 and from 1926 to 1942. Total gold production from the mining district through 1949 totaled 7.5 t (240,000 oz). An additional 7.7 t (249,000 oz) were produced during Galactic's tenure. Natural degradation of the outcropping sulfide-rich veins in the area and the early mining activity, including development of the Reynolds, Dexter and Iowa drainage tunnels in the late 1890s, have polluted the streams draining the area with heavy metals and acidic water. Names of the various tributaries to Wightman Fork, such as Iron, Alum and Bitter Creek, testify to this natural pollution. This degradation has reduced, or killed, aquatic life in several area creeks, including Wightman Fork, for many years before recent mining activity.

Jan 1, 1993

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009