Search Documents

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By Tracy Brettmann

A new method for estimating ground vibrations caused by pile driving was developed as a result of a vibration monitoring program performed for a large pile driving project. The method is accurate, rational and theoretically based starting with energy actually transmitted to the pile (not the rated or operating hammer energy). This energy is then assumed to be transmitted to the soil in the form of surface waves that attenuate from both geometric and material damping. The main input parameters for this method include the energy transmitted to the pile and the dynamic properties of the soil (wave velocity, material damping, and unit weight). In this study we concurrently measured both: (1) pile driving of 14-in.-square, 65-ft-long precast concrete piles with a Pile Driving Analyzer?, and (2) vibration levels at various distances away from the piles during driving. A geotechnical study for the site was also performed that included measurement of the dynamic soil properties using both crosshole and seismic cone testing. This paper presents the data obtained from the study and compares the results to the values estimated using this new method. Vibrations from pile driving is a serious matter that impacts virtually every pile driving project. It is important that accurate methods for estimating ground vibrations be available to engineers and contractors.

Jan 1, 1999

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

By R. V. Huff

An in-situ leaching technology was developed for copper oxide minerals at the Van Dyke deposit at Miami, Arizona. This paper discusses the process developed and the activities that occurred. Specifically, the activities of well installation, deposit data acquisition, leach testing and equipment development are reviewed. Installation and operation of the test facility are described.

Jan 1, 1988

By Norbert Patzelt

The high-pressure grinding roll was introduced about 10 years ago and has established itself in many applications. Most of these machines are used in grinding circuits in the cement industry. A few operate in conventional mineral-processing plants. Polysius has sold more than 350 Polycoms worldwide. An exception is diamond-ore processing in South Africa and Australia. This type of grinding system increases diamond liberation and reduces the capital costs for the downstream processing plant. There are several reasons why high-pressure grinding rolls have not been used more extensively in the mining industry: - The mining industry adheres to conventional grinding technology and regional preference for certain comminution circuits. - Design, scale-up and flowsheet assessment procedures are viewed as being immature and reduce confidence in the potential application of the technology. - Downstream process benefits are unproven on a plant scale.

Jan 1, 1995

By Pierre-Louis Migairou

After a period of development and experimentation ranging over 20 years, electronic detonators have now come to maturity and are becoming the first choice in many diverse applications like tunnelling, civil works, demolition works, quarrying, large scale open pit mining and underground mining. This paper demonstrates the versatility of electronic initiation systems by detailing a number of case studies in several applications as different as their geographical locations, and gives specific reasons explaining the popularity of electronics in each case.

Jan 1, 2009

By Lee R. Buhagiar

As a result of the increased seismic risk and the highly variable geology of Christchurch, finding costeffective foundation solutions has been a challenge for the Canterbury rebuild. The soil profile in Christchurch comprises both terrestrial (Springston Formation) and marine (Christchurch Formation) alluvial deposits with a high groundwater table. The result is a highly variable and interbedded soil profile which is prone to liquefaction and static settlement. Vibro-replacement stone columns are very effective in mitigating liquefaction in clean sand. However, the author’s experience has shown that vibro-replacement stone columns are also effective for treating silty and soft soil layers. Vibroreplacement stone columns can be used to treat these soft soils by increasing the composite soil stiffness and providing a load transfer path to the underlying dense soils. Another challenge encountered in the Canterbury rebuild is the cost of redevelopment of brownfield sites with contaminated fill. The costs of disposing this fill often make projects too expensive. Vibro-replacement stone columns have been used successfully to treat contaminated fill, providing a treated soil profile with uniform performance and reducing the cost of disposing of contaminated fill. This paper looks at several case studies in Christchurch, with highly variable soil profiles, where vibro-replacement stone columns have been used successfully to treat multiple soil layers, from contaminated fill to silty soils and soft and non-liquefiable silt.

Nov 1, 2022

By A R. Bye

The mining industry is facing some key challenges that provide a compelling case for geometallurgy initiatives. Over the last 30 years, the average grade of Australian orebodies being mined has halved while the waste removed to access the minerals has more than doubled. In the last eight years, the industry’s energy consumption has increased 70 per cent while multi-factored productivity has fallen 24 per cent. The paper documents a broad range of industry case studies which demonstrate strategies for gaining value from geometallurgy.The mining industry constantly faces the key questions of how significant ore variability is on mine valuation and how would knowledge of the variability change the mining schedule, mine to mill design and operation. Using case studies the paper describes the methods used for incorporating mineral extraction attributes into orebody models and their technical integration into daily operation as well as mine planning optimisation. While pit optimisation from a fully attributed geometallurgical model highlights areas of opportunity and risk it is shown that during the scheduling phase of mine planning that significant value can be added. The benefits from these projects included reducing geotechnical and environmental risk, improving mine to mill performance, option analysis and quantified cash flow risk. There is growing acceptance within the minerals industry that ‘realistically assumed modifying factors’ defined by a competent person/s are not sufficient to mitigate the risk of funding mining ventures. Geometallurgy is moving away from factored ore reserves to data-rich block models providing reliable information for mining, metallurgical and environmental considerations.

Sep 5, 2011

By I Neilsen, A Walker, A Hooper

Final landform planning in Deswik software was used to determine if integration into the mine plans could achieve better closure outcomes. Using the dump surface outputs from the Deswik Landform and Haulage Simulation (LHS) and the Reshape Landform tool, the project intended to:1.Review costs to achieve the final landform for several grade criteria scenarios;2.Quantify reshape volumes at several stages of the mines development with the objective to contribute to margin ranking inputs; and3.Identify rehabilitation cost reduction measures such as backfilling ramps and pits.CITATION:Neilsen, I, Walker, A and Hooper, A, 2018. Case studies for integrating rehabilitation planning with mine planning in strip mining, in Proceedings Life-of-Mine 2018, pp 93–95 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By S J. Loach

F-Series reconciliations are formal comparisons of estimates and measurements of ore quantity and quality made at pre-determined points along the mining value chain. F1 is the ratio of ‘Depleted Grade Control Ore/Depleted Long-term Model Ore’ and validates the models upon which Resource and Reserve statements are based. F2 is the ratio of ‘Produced Tonnes and Grade/Depleted Grade Control Ore (-) Changes in Pre-Crusher Stockpiles’ and validates that the ore tonnes and grade delineated in the pit are being accurately extracted and correctly delivered to the processing plant. These factors provide important corporate assurance for a mining company by providing quantitative feedback on model-predicted tonnes and block grade estimates. Since 2009, BHPs Western Australian Iron Ore F-Series reconciliations have been calculated in a single, centralised sequel-server database. This software routinely collates data regarding mineral resource block model depletions, grade control model depletions, pre-crusher stockpile inventories and production tonnes and grade measurements and then calculates F-Series factors for both tonnes and product quality. This paper will present case studies where reconciliation factors were used to identify improvement opportunities leading to projects that improved our models and subsequent forecasts of production tonnes and quality. In addition, it will show how reconciliation factors are tools that monitor control during periods of rapid change and provide feedback on the effectiveness of improvement projects.

Sep 18, 2023

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By Sharon K. Reamer, Yvan Sifre, Klaus-Gunter Hinzen

"Three case studies are presented that illustrate the successful application of firing timeoptimization (hybrid modeling) in the quarry environment and for a construction site. In allcases, the method requires the measurement of at least one in situ, single hole explosion asa representative model of the desired blast design."

Jan 1, 1993

By S. McAlister

"Falcon Concentrators Inc. has developed a high capacity centrifuge for the recovery of fine, free gold as well as other metals and minerals which were previously thought to be unrecoverable by gravity means. Development started in the early 1980's and the first commercial operation was commissioned in 1986. Gold applications include scavenging conventional gravity and cyanidation circuit tailings, cleaning gravity concentrates, cleaning flotation concentrates to melting grade, scavenging flotation tailings, and placer mining. Recent development work by Falcon has expanded the applications scope of the centrifugal concentrator to include many minerals amenable to gravity concentration including iron, tin, industrial minerals, and hazardous wastes. This paper discusses this technology including its history, present applications, and future potential. OVERVIEW OF CENTRIFIJGAL CONCENTRATIONUsing centrifugal force to enhance the separation of materials by differential specific gravity has been researched for over a century. Many attempts have been made to concentrate minerals in high gravity fields. Patents were granted on this subject as early as 1891 (see Figure 1). Patenting activity continued into the 1920's and has been relatively quiet since. It is significant that no centrifugal system of gravity concentration has been broadly accepted by the mineral processing community until recently. Much of the world's reserve of mineral deposits which are amenable to conventional gravity concentration technology (coarse-grained) have been mined and therefore there is an increasing demand for technology which can economically recover the fine-grained gravity recoverable minerals in the remaining deposits. In addition, centrifugal concentration can play an increasing role in solving environmental problems by offering an inexpensive method of concentrating hazardous materials such as uranium, plutonium, mercury, lead, and other heavy metals. The overall cost of disposing of these substances safely can be drastically reduced if they are recovered into a concentrated form prior to disposal."

Jan 1, 1992

By D. H. Horswill

The paper point out considerating how mining activities contributed to sustainability, it is important to consider how exploitation of a finite resource can be regarded as sustainable. The now well–recognized concept of sustainable development holds that society’s pursuit of development that meets current needs should not compromise the ability of future generations to meet their own needs. Sustainability, then, contemplates multigenerational enjoyment of a quality of life that includes social and economic benefits and a healthy environment in which to live. In this sense, the benefits of our activities must always exceed the risks. Many other companies are also making significant inroads along the path to sustainability.

Sep 13, 2001

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.