Search Documents

By Emil Gathmann

STEEL as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really not belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True unkilled, or effervescing, steel should contain large volumes of gases, which are evolved while the metal is being teemed, or cast from the ladle nozzle into the mold, and while the temperature of the steel is being reduced prior to the solidification or freezing of the steel, the upper portion, or top, of the ingot remaining liquid due to the evolution of gases until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and form the skin blowholes, at times troublesome, in the forming solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in various products if they occur well within the interior of the ingot where they will not be subject to oxidation upon the ingot's cooling and subsequent re-heating and rolling or forging. Very little top or bottom discard is taken from this type of ingot as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated for by the innumerable blowholes distributed throughout the body of the , ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 8, 1920

By J. C. Van de Water

In June the supply of M3 army demolition powder being used for mudcapping was depleted and we switched to 4 by 8, 60% Special Quarry Gelatin dynamite. This size cartridge has proved convenient, as a half stick will handle the average boulder. By keeping the gelatin in the paper while cutting it in two, there is little contact with the gelatin and therefore fewer headaches among the powdermen. To further help prevent the headache nuisance the men are furnished with plastic coated gloves. Boulder breaking costs as reported last year were $0.426 using M3. This year, 8180 boulders have been broken with M3 at a cost of $0.472 each and 7479 with 60% Quarry Gelatin at a cost of $0.660 each. This rise in cost is due entirely to the greater cost of the Gelatin as the method has not changed.

Jan 4, 1950

By J. C. Van de Water

THE original trucks at Castle Dome were 30-ton Knuckeys with 150 hp, H-series Cummins engines and 15-ton Euclids with the same engines. The Euclids were used early in the operation, working with 2 1/2-yd Diesel shovels on stripping and later in opening new benches where the lack of room favored the smaller trucks because of their shorter turning radius. They have also been used on road building and similar jobs. On regular production, where the 30-ton trucks can be used, they are not economical.

Jan 11, 1951

By Albert L. Toenges

(1) The Castleman Basin was investigated by diamond drilling, engineering examination, and geologic study. Agreements permitting investigation of about 14,700 acres of land were entered into with 79 landowners. Eleven beds of coal between the horizons of the Harlem and Mercer beds were penetrated in drilling. These beds from top downward are: Harlem, Upper Bakerstown, Lower Bakerstown, Brush Creek, Upper Freeport Rider, Upper Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Mount Savage, and Mercer. The total estimated reserves of coal (measured, indicated, and inferred), 14 inches or more thick, in six beds follow: [Coal bed: Etimated reserves, tons Harlem _______________________ 23,430,000 Lower Bakerstown _______________ 44, 688, 000 Brush Creek ____________________ 23, 694, 000 Upper Freeport __________________57, 731, 000 Upper Kittanning ________________ 40, 450, 000 Middle Kittanning ______________42,276,000 Total________________________ 232,269,000]

Jan 1, 1952

By C. N. Greene

I am sure it is obvious to all of you that a complete program of casualty and property insurance is as necessary for any tunneling contractor as it is for anyone else involved in trade in the United States today. Going beyond those general undefined terms, there are many areas that need specific attention, particularly for contractors, regardless of size. WORKERS' COMPENSATION Workers' Compensation is mandatory in all states and the District of Columbia. In most of the states, private insurance provides this coverage. In a few states, the state operates Workers' Compensation funds, some of which are competitive with the private sector and others are operated on a monopolistic basis. Under a monopolistic setup, you have no choice, you must buy coverage from the state. Self insurance of the Workers' Compensation risk is also an alternative in most jurisdictions. With a contractor operating only in the U.S., the coverage extensions are few in number. If your work brings you anywhere near navigable waterways or land extensions thereof, you should have both U. S. Longshoreman and Harborworkers' coverage, as well as Employer's Liability coverage for the master or members of the crew of a vessel.

Jan 1, 1983

A coal mine located in southern West Virginia recently set a world record for daily low-seam coal production using a Cat automated longwall plow system. In a 24-hour period on April 10 and 11, 2014, the Pinnacle Mine longwall produced 32,411 t (35,724 st) from the Virginia Pocahontas No. 3 Seam, in a seam height of just 1.42 m (56 in.) along the 298-m (980-ft) longwall face. The Pinnacle Mine, located near the town of Pineville and owned by Cliffs Natural Resources Inc., an international mining and resource company, operates a Cat Gleithobel GH1600 Longwall Plow System. A previous record was set by this system at Pinnacle in August, 2012 when 29,423 t (32,430 st) were mined in a 24-hour period. The record was set by the same system, mining its second panel after a comprehensive rebuild was performed by Carter Machinery, the Cat Dealer in that area. The rebuild encompassed a complete rebuild of the headgate and tailgate armored face conveyor (AFC) drive, the headgate and tailgate special AFC pans, the stageloader drives and return end, the complete crusher and all gearboxes for the plow, AFC and stageloader. Carter acquired the rights to sales and aftermarket support associated with the former Bucyrus mining products, both surface and underground, in 2013. ?Supporting and rebuilding a longwall plow system was a new experience for the Carter service team,? said Chris Curfman, president of Caterpillar Global Mining Sales and Support Division. ?However, given the record production results attained by the rebuilt system at Pinnacle, it?s obvious that they are up to the challenge of supporting the underground product lines at the same high standards and quality level that they have been delivering for many years on the traditional Cat surface mining products.? Tom Bluth, president of Caterpillar Global Mining Products Division, said, ?Caterpillar congratulates the Pinnacle team for this great achievement. Without their efforts and dedication this record would not have been possible. To safely deliver that kind of output from such a thin seam is remarkable. We have been privileged to work alongside their team to demonstrate the capabilities of Cat longwall mining technology. ?

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

Cataclysmic or flood-like release of gas-charged brines, hydrocarbons and slurries accompanied widespread mineralisation of Upper Devonian environments. These are well represented in the Canning and Burdekin Basins of Western Australia and Queensland respectively.The Burdekin Basin provides particularly instructive vein structural sequences. These fall into organic residue to carbonate paragenetic sequences which are known elsewhere to record progressive decarboxylation. Fibrous veins indicate overpressure in fractures with organic residues, acids and gas derivatives driven to overlying groundwater flows. This combination of large flow rates and potent organic mineralisers led to extensive arsenical rare-metal mineralisation which is similar to that concentrated in Upper Devonian extinction horizons of the Canning Basin. Organic-residue mineralisation appears concentrated by certain hvdrostructures and targeted upon particular species. These controls need to be understood to guide modern management stragegies for mineralised organic and nitrogenous wastes.

Jan 1, 1990

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By L. Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pinpoint the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable temperature readings and gas analyses could have verified satisfactory activity. Hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: good record keeping is a necessity for collection of representative catalyst samples; reliable operating data is an inevitable starting point for all analysis; and trending of operating data is a must for plant optimization and troubleshooting. In addition, these catalyst management tools will give continuous updated knowledge of the catalyst status in each bed, providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking operating data, temperature optimization and good record keeping.

Jan 1, 2009

By Haydn H. Murray

The three major catalyst markets that utilize industrial minerals as raw materials are petroleum refining, chemical processing, and emission control. Because of economic, competitive, and regulatory pressures, catalyst producers are pushed to develop products with improved performance to meet changing environmental standards. Also, refiners are demanding new families of cracking catalysts that will crack residual fuels. In 1987, worldwide cracking catalyst sales amounted to $457 million (Occelli, 1988a). Recently enacted federal and state laws to improve air quality have prompted strong growth for environmental catalysts, which in 1989 accounted for more than a third of the $1.9 billion catalyst market in the United States (Farrauto, Heck, and Speronello, 1992). A catalyst is a material that promotes or enhances a chemical reaction but does not itself enter into the reaction. One of the more important mineral groups used as catalysts is clays. The first recorded use of clay as a catalyst was its use in the dehydration of alcohol (Bondt et al., 1797). Clay minerals that are used as catalysts are kaolinite, halloysite, smectite, palygorskite, and sepiolite. Minerals used as catalysts, catalyst supports, or as a raw material to make zeolites are kaolinite, halloysite, sodium montmorillonite, calcium montmorillonite, hectorite, palygorskite, sepiolite, talc, calcined kaolinite, gibbsite, chlorite, and titanium dioxide.

Jan 1, 1994

By Jorge M. C. Soares

The CO oxidation reaction has been studied on Au/TiO2 catalysts prepared by incipient wetness (IW) and deposition-precipitation (DP) methods. Additionally the assessment of activity was also conducted on simple gold compounds (Au2O3 and Au(OH)3) and their physical mixtures with TiO2. We have found that there are three types of CO2 production from fresh catalysts, which are only dried, namely: Non-catalytic Type I (low temperature CO2 production); Non-catalytic Type II (higher temperature CO2 production) and Catalytic Type III. The DP catalysts are far more active for Type III reaction, showing activity already at room temperature, whereas the IW catalysts generally do not show steady state conversion until T>673 K. This is due to both large particle size and the presence of residual chlorine for the latter. No truly catalytic activity was found for low temperature CO oxidation on gold precursors on their own, although both Au2O3 and Au(OH)3 react well with CO even at room temperature in an irreversible manner (Type I reaction). Despite that, catalytic activity was obtained by mixing Au(OH)3 or Au2O3 with TiO2 which gives further emphasis on the importance of a good contact gold/support and the absence of chlorine.

Oct 1, 2003

By P. E. Nolan

The disproportionation of carbon monoxide is an important aspect of reduction processes, in the production of carbon filaments for composites, and in the removal of CO from CO,. It can also be a hindrance, causing carbon fouling of equipment and metal dusting. The reaction is thermodynamically favored at lower temperatures, but it occurs slowly. Catalysis of the reaction by transition metals has been examined. A materials science approach to the selection of a catalyst material and of optimum operating conditions is being taken in the present work. Of particular interest is characterization of a catalyst that can be repeatedly regenerated to prevent deactivation in long term use. Experimental data on a less studied catalyst, ruthenium, are reported.

Jan 1, 1992

By M. Kawakami

In the blast furnace, the reduction of iron oxide and gasification of coke occur simultaneously. It is well accepted that the gasification reaction controls the simultaneous reaction. Therefore, it is important to develop highly reactive carbonaceous materials. It is also known that the reaction is accelerated catalytically with the addition of some materials. In the present work, the catalytic effect of iron, nickel and CaO on the gasification of graphite and coke was examined. The catalytic effect of iron, nickel and CaO on the reaction rate of graphite was noticed The effect was larger at lower temperature. At 1373 K, the effect almost vanished. The effect was larger in the order of CaO, iron and nickel. The reaction rate of de-ashed coke increased by the addition of iron and nickel. The effect of iron was larger than that of nickel. The effect was larger at higher temperature, which was contrary to the case of graphite. The reactive surface area increased also by the addition. Therefore, the catalytic effect on reaction rate might be attributable to the increase in the reactive surface area.

Jan 1, 2006

By M. Moinpour, Y. K. Rao

The catalysed direct reduction of copper sulphide with carbon and lime was investigated in the range 850-1000 degrees C using Cu2S-CaO-C and Cu2S-4CaO-4C reaction mixtures. The effects of the catalytic additives K2CO3, Li2CO3, Na2CO3, NaF, Na2SO3 and the ternary eutectic (K,Li,Na)2CO3 were determined. Potassium carbonate, sodium fluoride and the ternary appear to be the most effective catalysts for the direct reduction process. The rate enhancement of the catalysed carbothermic reduction of copper sulphide in the presence of lime was explained in terms of the catalysis of the Boudouard reaction

Jul 1, 1991

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991