Search Documents

By Anthony Harding, Rodolfo D. Aradas, Juan M. Fernandez, Darío Tsingas

"The adoption of tunneled combined sewerage interceptors and outfalls leads to design linings which are often subject to internal pressures that are larger than the external pressures, resulting in significant tension loads. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining. However, improvements in concrete technology and the need to seek efficiency in terms of time and costs, have driven designers to consider single pass segmental linings. The Riachuelo Sanitation project in Buenos Aires is subject to these constraints both upstream and downstream of a sewage treatment plant. This paper describes how the challenges of up to 2 bar pressure differential have been addressed by careful analysis of soil structure interaction to ensure that the full benefit of external ground pressure is realized, resulting in a more optimal design for the constructor both in terms of cost and time. INTRODUCTION The construction of long sewerage interceptors and outfalls is becoming an increasingly common piece of infrastructure for modern urban cities facing a large water front and estuarine conditions, which are under a significant environmental burden imposed by decades of sustained growth. Such works intercept most of the distributed sewage discharges to then divert them to a central treatment point from which it will be finally diffused via an outfall into a water body capable to accept these discharges under acceptable environmental conditions. Depending on the magnitude of the sewage load to be handled, the configuration of the urban environment and the conditions of the receiving water body, both in terms of oceanography forces and seabed conditions, these schemes will vary in length, conveyance capacity and design and construction requirements. When conditions permit, the current trend is the execution of long outfalls using flexible solutions (such as the use of HDPE pipes) which usually require some form of concrete ballasted weights to resist off shore dynamic forces when directly laid over the sea bed. However, this concept faces limitations when the conveyance requirements indicate the need for large diameters (typically above 3000 m) and also when the outfall needs to avoid deep features off shore such as navigation channels. When this occurs, tunneling, particularly segmentally lined tunnel constructed by TBM emerges as the most feasible approach for large diameter, long deep outfalls. The operating conditions often result in internal pressures that are larger than the external pressures, resulting in significant tension loads in the lining. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining."

Jan 1, 2016

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

By Zofia Swierczek

This paper reports the results of a detailed mineralogical study of typical, low-grade Australian nickel laterite run-of-mine ores. Successful development of an effective beneficiation process for upgrading such low grade laterite ores relies on good knowledge of the laterite mineralogy and the value metal(s)? distribution characteristics. Both QEMSCAN and quantitative X-ray diffraction techniques were used to conduct the mineralogical analysis of three types of laterite ores, and the results were compared with those obtained by chemical analysis. Some of the major challenges faced included accounting for the mismatch between the nickel values measured by QEMSCAN and those recorded by chemical analysis. This was primarily due to the relatively low concentration of nickel in the ores and its wide dissemination among several major host minerals in complex association. Careful analysis showed that the limit of nickel detection in iron oxide host mineral grains under normal operating conditions was around 4%. Keywords: nickel laterites, mineralogy, characterisation, QXRD, QEMSCAN

Sep 1, 2012

By Robert J. McCarthy

Mining has a record of achievement in developing and adopting new technology to facilitate the extraction of increasingly challenging resources. Certainly larger, or more capable, mining equipment has allowed mining companies to mine mineral deposits at lower unit costs; however, there has also been the advent of computerized systems that aid in the management and tracking of mining operations. Unfortunately, the latter computerized systems have not always had the success anticipated with their implementation. This paper explores the view that increased transparency of the planning and operating cycle in a mine, as provided by certain computerized systems, can result in some resistance from those whose work becomes ?exposed?. Examples are drawn from industry-leading technologies for both mine management and reconciliation that illustrate the issues and challenges that result. The adoption of appropriate change management principles is suggested as a best practice in planning and mitigating the challenges in implementing technologies which increase transparency in the mining environment.

May 1, 2011

By A. D. S. Gillies

Inertisation is used to enhance the safety of underground mine areas either to avoid the potential for a combustion event or to stabilize a situation after an ignition, fire or heating. The primary objective of a recently completed Australian Coal Association Research Program (ACARP) study was to review coal mine inertisation and in particular to focus on use of the Polish mine fire simulation software Ventgraph to gain better understanding of how various inertisation units interact with the complex ventilation behavior underground during a substantial fire. Critical aspects targeted for examination under the project grant included location of the unit for high priority fire positions, size of borehole or pipe range required, time required for inertisation output to interact with and extinguish a fire, effects of seam gases on fire behavior with inertisation present and main fan management. A major accomplishment of the project has been to take findings from the simulation exercises to develop inertisation related modifications to the Ventgraph fire simulation program in conjunction with the Polish program authors. Selected mines were ?evaluated or audited?as to the ability to deliver inert gases generated from GAG units to high priority underground fire locations .A coding system has been developed and many potential underground mine fire sources cannot be successfully inertized with the GAG docked at the current specified point; this is particularly so for fires in extended areas of workings or in panels. There is a limit to the ability of the GAG jet engine to deliver exhaust down smaller dimension borehole. There is a need to examine the use of the GAG for production or proactive uses in a wider application in Australian mines responding to recovering from mine fires, spontaneous combustion heating?s, elimination of the potential explosibility of newly sealed gobs or inert mines or mine sections on closure. Some of the current uses of low flow inertisation facilities could be more effectively undertaken with the GAG unit.

Jan 1, 2009

By P. Michael

Proponents of geomorphic mine land reclamation have criticized current reclamation practices in the coal fields of steep-sloped Central Appalachia as too narrowly focused on civil engineering principles and neglectful of the functional and aesthetic benefits of reclaiming mine sites in ways that mimic natural landforms and drainage patterns. They observe that current mining and reclamation practices are radically transforming the mountain-and-valley terrain into gigantic flat plateaus and, in doing so, disrupting the beauty and ecology of the natural landscape. Instead of designing and constructing linear or planar surfaces and unvarying slope gradients during the reclamation process, they recommend ?landforming,? i.e. the adoption of curvilinear, compound slope forms that blend well with the surrounding physiography and represent the result of naturally stabilizing geomomorphic processes. The authors feel that the concept of geomorphic mine land reclamation is sound, however, its application to the Central Appalachian coal fields faces significant--albeit not insurmountable--challenges. They include: (1) existing reclamation enforcement regulations that are focused on civil engineering principles and not explicitly supportive of geomorphic methodologies; (2) regulatory agencies? current intent to limit the down-gradient reach of excess spoil fills in order to allay disruption or burial of natural streams; (3) actual or perceived increases in reclamation costs; and (4) the challenge of designing and constructing ?natural? landforms that are mature and stable in an otherwise youthful, erosional landscape.

Jan 1, 2010

By T J. Callaghan

The Avebury nickel mine in Western Tasmania is a disseminated nickel sulfide deposit hosted in intensely metasomatised Cambrian ultramafic resulting from later Devonian granite related hydrothermal activity.Variable metasomatism of the ultramafic has formed two distinct gangue mineral assemblages. Less metasomatised ultramafic is comprised of fine grained black antigorite with minor disseminated chromite, magnetite and pentlandite. Intensely metasomatised ultramafic is altered to a pale grey or green, coarsely crystalline tremolite/actinolite and diopside assemblage with minor magnetite, chromite and sulfides. Both gangue mineral assemblages are frequently intermixed in ore grade mineralisation.The bimodal gangue of either serpentinite or metasomatised ultramafic presents challenges to drilling, mining, resource estimation and mineral processing as they possess very different physical properties. Mineralised serpentinite has a mean bulk density of 2.8 g/cc and the ultramafic skarn a mean bulk density of 3.2 g/cc. Physically, the ultramafic skarn is hard to break percussively creating difficulties in the crushing circuit and reducing mine development rates. However, it is non-abrasive and grinds readily, resulting in increased diamond drilling rates and increased mill throughput. Conversely the serpentinite gangue is softer and breaks easily resulting in accelerated development rates and crushing circuit throughput. However, its fibrous nature reduces grinding efficiency, increasing bond work indices and reducing diamond drilling rates.Predicting the ratio of serpentinised to metasomatised ultramafic is possible through use of the resource blockmodel, assisting mine scheduling, predicting mill throughput rates, energy consumption and grade control drilling rates.CITATION:Callaghan, T J, 2017. Challenges of bi-modal gangue mineralogy in mining geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 23–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Anthony G. Fonseca

About 45% to 50% of the coal mined in the United States passes through coal preparation plants. East of the Mississippi River, this number increases to about 75% to 80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation is an effective process that achieves 75% to 80% ash reduction, 15% to 80% trace element reduction and 85% to 90% Btu recovery. It is less effective for pyrite reduction (35% to 70%) and on-line operating time (40% to 60%). It also suffers from obsolete control systems. In coal preparation, raw coal is modified to a more preferred form to enable its use. The methods used to achieve this modification must be cost-effective and appropriate to the raw coal, the scale of production and the end-user requirements.

Jan 1, 1995

By Marco Sonnenschein

As time is costly, engineering companies have developed methods, procedures and mechanical equipment to tunnel faster. But the best excavation method will not be able to cope with the time pressure if there is not a reliable backup system. Therefore, the application of belt conveyors for tunnel boring machine (TBM) drives as well as for drill-and-blast driven tunnels assure a quick and smooth removal of excavated soil in order to enhance the efficiency of the tunneling equipment. During the last 10 years, belt conveyor systems have achieved ?state-of-the-art? levels and have become the first choice for muck removal systems in both TBM and drill-and-blast driven tunnels. Because time has become such a key criterion in tunneling projects, it is essential that all equipment is operated so as to derive optimum efficiency and minimize costs. Efficiency also means to think about new tasks for existing technologies.

Jan 1, 2012

By Francois P. Leroy

In the quest of studying the assigned blocks of seafloor for deep water mining, each member country of the ISA is thirsty for accurate information as to the level of resources available. Manganese nodules represent a large portion of the resources and are as precious as they are hard to locate and harvest. Resolving such challenges is what drives the technology development and yields instruments and products capable of serving this field of research. This presentation will study how manufactures of oceanographic instruments have pushed the technology envelop to in order to transform a collection of sensors and instruments into a seamless and adapted assembly working to serve the researcher and prospector in the challenging field they operate. Deep water data collection is characterized by the following challenges: ? Deployment, recovery and handling of the vehicle ? Producing high resolution at great distances ? Positioning that data with accuracy to relocate Teledyne Marine will present the work performed in its engineering laboratories to produce sub systems and systems now capable of delivering key information necessary to the proper cataloguing and exploitation of deep water mineral mining. Understanding and controlling the alternative resources available to each country will allow better management of current traditional land based minerals.

Jan 1, 2010

By Bruce D. Hebb, Shahin Shadlou

Fiber Reinforced Polymer (FRP) is an excellent material choice for a broad spectrum of corrosive fluids and, in many cases, offers the best value per dollar. FRP Flanges present the greatest design challenge of all standard piping components. The theory underlying the design of flanges is very complex. In addition, due to the nature of FRP material, proper fabrication of the flanges is as critical as the design. In this review, the challenges of making FRP flanges along with the design techniques and best practices of fabrication that will lead to a high-quality flange will be discussed.

Feb 1, 2024

By N C. Steenkamp

The Northern Cape Province of South Africa is host to the Kalahari Manganese Field (KMF). The northern portion of the KMF hosts high-grade manganese referred to as Wessels’ type ore and is mined mostly from underground operations. WorleyParsons TWP is currently involved with the development of a ventilation shaft for one of these mines. The main challenge is to develop through the unconsolidated Kalahari material and weathered portion of the Karoo formation. These formations are preserved very erratically over short distances. A lack of understanding of the unique challenges presented for developing shafts in this area has resulted in the failed development of a shaft on an adjacent property and over-expended budgets on others.The renowned red sand of the Kalahari forms the top several tens of metres and overlies a horizon of gravels and calcrete that pose seasonally variable water ingress problems. A very stiff red clay horizon is then intersected. The Red Clay is prone to swellling during excavation and has been the main stumbling block on previous constructions. The standard approach has been to develop non-stop through this layer. The red clay is underlain by another horizon of calcrete, gravel and conglomerate that marks the bottom of the formation. The top of the Dwyka Tillite (Karoo Formation) is usually highly weathered and has a distinctive yellow colour. The weathered tillite is highly susceptible to drying and becomes friable. At reef-intersection, the combination of subhorizontal bedding and joints with the dominant subvertical faulting results in potential wedge failures in the manganese and ironstone units.This paper describes the geotechnical issues identified during the planning of the ventilation shaft and the risks associated with development through the Kalahari and weathered Karoo Formations. A new approach to developing ventilation shafts in overcoming these challenges is recommended.CITATION:Steenkamp, N C, 2014. Challenges of developing a ventilation shaft in Kalahari and Karoo formations, Northern Cape, South Africa, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 81–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By L Lorenzen, H Muller, L Bernard

Australian companies and consultants are becoming ever more involved in projects in African, South American, East European and Middle Eastern countries. However, significant differences in culture and approach to projects sometimes make these projects challenging for reasons that are not purely technical. Often the challenges are rather related to how the project owner and local authorities perceive the reality. These perceptions and sometimes unrealistic expectations regarding project costs and potential outcomes need to be addressed by the æWesternÆ project developer and consultant.This paper will discuss the specific experience of Snowden in studies commissioned by companies from such countries for the development of very large, low-grade gold deposits in some of the most inhospitable areas in the world. The paper will further review similar projects undertaken in other ænew worldÆ countries and compare these to the initial Snowden experience.As the process operating costs of operations in many of these countries are extremely competitive when compared to the typical Australian operating costs, the paper will review the operating costs and the factors which may be pertinent to a large project of this nature, both in the Australian and the ænew worldÆ context. Will Australian-based operations be able to compete in the global gold market when the gold price softens again, as it will do at some stage in the possibly not-so-distant future?CITATION:Muller, H, Lorenzen, L and Bernard, L, 2013. Challenges of developing low-grade deposits in ænew worldÆ countries from a mining consultantÆs perspective, in Proceedings World Gold 2013 , pp 307-314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

By Balasubramani M., Ramana P. V., Bairagi K.

This paper is a case study of an earthen Cofferdam, constructed for a deep excavation at Intake location in river Aaundha, Maharashtra, India. A 12 m (39 ft) deep excavation was made to construct the Intake well. The natural soil profile at this location is clay followed by rock. An earthen Cofferdam of maximum height 7 m (23 ft) was made around the periphery of the excavation. Cofferdam embankment and excavation slopes were analyzed using the finite element software PLAXIS-2D. Clayey sand was proposed as filling material during design, but clayey soil was used for the embankment formation during execution. The embankment was built up to 5m height in July 2017 and completely submerged due to monsoon. In February 2018 embankment height raised to 7m (23 ft) by filling the soil over the existing submerged embankment. After a few days of completion of the Cofferdam construction, the inside slope of the embankment had started sliding due to continuous dewatering. The design and execution of deep excavation with earthen Cofferdam for waterfront structures are challenging. The selection of filling material for embankment formation and dewatering techniques plays a vital role in the safety and stability of the embankments. Although all the safety measures were taken during the design, execution challenges are unpredictable.

Nov 1, 2022

By C. Ernst

The underground operation at Barrick?s Cortez Mine, located near Elko, NV, required the construction of a 12 foot diameter smooth-lined ventilation shaft. Barrick preferred to mechanically excavate from the ground surface without putting people in the excavation and considered blind drilling by Frontier-Kemper Constructors the best option. Design and construction challenges arose throughout both the excavation and lining stages. A large portion of the rock to be drilled was highly fractured. Important risks that were addressed included water loss into the formation, zones of squeezing ground, damage to drilling tools caused by blocky ground and fallout, and potential hazards during cast-in-place concrete lining. Detailed explanations of these challenges and the methods used to overcome them will be described.

Feb 23, 2014

By J. K. Armstrong, C. Feyerabend

"As mines are constantly growing and expanding, so do the challenges for emergency response teams. They have to keep up with the pace set by current and future production techniques. Although mines have now reached depths of several kilometres and their dimensions and complexity are that of an entire city, mines rescue still must be able to reach the most remote areas within the mine in a swift and safe manner. The duration of breathing apparatus and physical human capabilities are limitations. Therefore, alternative methods have to be explored to extend the time under oxygen for mine rescue teams without putting additional stress on the team members. To address this global trend, Dräger, Goldcorp and PAUS have partnered to develop a mine rescue vehicle that allows mine rescue teams to travel for an extended period of time through a contaminated atmosphere without the use of breathing apparatus, thus extending the range of their mission. By applying currently available techniques, the safe expansion of mine production can be ensured, giving mine rescue teams the ability to respond to accidents in a safer and faster way. INTRODUCTION With the reduction of easily accessible natural resources, there is a global trend toward searching for higher ore grades underground and/or continually expanding mines underground to extend their lifetime. While in some areas this trend has just begun, in other countries mines are reaching depths or horizontal dimensions that pose extreme challenges (Codelco, 2016). These challenges include safety relevant topics, such as rock stability, heat and seismicity, but also more basic issues such as distances to the working face, which can become crucial considering the cost to develop a new shaft or decline. To overcome this, there is a growing interest in collaboration among various stakeholders to drive the development and support of deeper mines and tackle the complexity of underground mining. This is evidenced by the fact that several industry and research groups and networks have formed, e.g. the I2mine project in Europe and the Ultra-Deep Mining Network by the Centre for Excellence in Mining Innovation in Canada. Due to commodity pricing and the trend toward renewable energy, metal/non-metal mining will be the driving force behind this development."

Jan 1, 2019

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

The prime objective of geometallurgy is to improve the profitability of mines through the use of spatial models of rock properties that have a significant impact on value. Although a key property is the grade of the component of interest, because it directly influences the revenue from saleable material, increasingly attention is being focused on other attributes. These 'non-grade' variables may have a less direct, but equally profound impact on value, either by reducing potential revenue (eg lowering recovery, deleterious elements, etc) or increasing mining or treatment costs (eg comminution, grindability, throughput, reagent use, etc). Collectively, these variables have been described as 'geometallurgical'. There are three main areas of activity required to realise the value of geometallurgy: 1. acquisition of appropriate data through sampling and measurement, 2. building spatial models of geometallurgical variables, and 3. using these models to optimise value. Each of these is built on the foundation of the preceding step. In building reliable spatial models, it is critical that the amount of error introduced to data by the sampling and measurement processes is understood and quantified, in order that the inherent variability of the component of interest can also be properly understood. Management of the quality of grade variables is now applied (with different levels of diligence and success) across nearly all sectors of the mining industry, not least because of the necessity to adhere to Codes of practice (eg JORC, 2004). The necessity for quality management and at least the broad framework of what to do in practice is reasonably understood by many relevant professionals. There are also a number of tools, including software products, statistical analyses and presentation formats, available for those managing grade data. It is also abundantly clear, that in many cases people have little understanding of why they are doing particular quality control activities, or how to sensibly interpret the results. The same is not true for many geometallurgical variables. In almost all instances the authors have seen, the magnitude of sampling and analytical/measurement error variance embedded in geometallurgical test data is untested and unknown. This is partly because until relatively recently, metallurgical data has mainly been collected for the purpose of process and mill design, with few, expensive tests carried out on 'average' samples of the orebody. Increasingly however, there is a move towards collection of much larger data sets from spatially distributed sampling, and thus a growing necessity to understand the errors inherent in both sampling and analysis of these types of variables, and how to manage them. In order to understand how the quality management practices applied to grade variables can be extended to geometallurgical variables, it is essential to understand the theoretical foundation that supports these practices. This requires an analysis of the concepts that underpin the 'principles of additivity' (Matheron, 1963), the 'theory of sampling' (Gy, 1982, Pitard, 1993), and 'statistical process control' (Shewhart, 1930). Relevant concepts are then integrated to form a foundation to develop methods to improve the quality management of geometallurgical variables. Application of this framework will significantly increase the integrity of geometallurgical data, the reliability of geometallurgical models and ultimately the value derived from implementing geometallurgy. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Mar 1, 2010

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022