Search Documents

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By D Preedy, J K. Claflin, S R. J La Brooy

This paper summarises the lessons learned during a recent carbon reactivation kiln upgrade project at the Sukari Gold Mine in Egypt. The kiln is being replaced to ensure that the plant achieves full value from the current throughput expansion from 5 to 10 Mt/a.The suitability of the original engineering design criteria for kiln selection and the adequacy of the original kiln are reviewed in the light of the carbon chemistry, operating experience and a site inspection of the kiln. Particular aspects of the reactivation facility are discussed including: predrying, preheating, feeding, gas seals, kiln heat transfer, steam injection, counter-current sweep gas flow, carbon cooling, fines minimisation and removal.Design criteria for a carbon predryer, reactivation kiln and cooler combination for carbon heavily fouled by high molecular weight frothers and collectors are discussed and the abridged Ausenco datasheet for the combination is presented.Responses to a request for a budget price sent to most of the worldÆs suppliers of carbon regeneration kilns are summarised.CITATION:Claflin, J K, La Brooy, S R J and Preedy, D, 2013. Ausenco carbon reactivation design criteria, in Proceedings World Gold 2013 , pp 401-410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By Bill Shand

"Placer Dome - Campbell Mine is a gold mine located at Balmertown in the Red Lake District of North Western Ontario. During the last 50 years, the mine has produced over ten million ounces of gold.A change in ball mill grinding media was made in August 1998 from 1.5” diameter forged balls to 1.5” diameter, 18% chrome balls. This was done to reduce grinding media consumption and to potentially help flotation performance.A marked ball test done in September-October 1999 showed that, of the alloys tested, 18% chrome was the optimum for the ore at Campbell Mine. The test showed that consumption of chrome balls should be 3 times less than forged balls.In December 1999, the ball size was increased from 1.5” to 2” in an effort to reduce the amount of oversize rock discharging from the ball mill. This change in size was successful.Grinding media consumption for the ball mill decreased 73% from 1.20 kg/tonne before the use of chrome balls to 0.327 kg/tonne after the use of chrome balls. This clearly indicates that, for the ore at Campbell Mine, there is significant savings in grinding media by using chrome.Grinding ball costs were reduced by 59% from $O.88/tonne of ore milled to $0.36/tonne of ore milled representing a saving of $298,000 per year. This also clearly indicates that using chrome balls is a benefit at Campbell Mine.Test work to show that chrome grinding media is beneficial to flotation has been inconclusive so far but is still ongoing.No tests have been done to see if there would be a benefit with an even higher chrome percentage in the grinding media. Test work in this area is also planned for the future"

Jan 1, 2001

By Jiann-Yang Hwang

Microwave heating has been proved an effective method to rapidly heat iron oxide. This offers an opportunity to apply microwave heating in the steelmaking process. The reduction reaction of iron oxide is traditionally achieved at high temperature with reducing gases such as H2 and CO generated from various sources, including coke, coal, and natural gas. This study investigates the differences in iron oxide reduction using conventional and microwave heating under H2 and CO atmospheres. A special microwave thermal gravimetric device was designed and built to facilitate the investigation. With this device, iron oxides can be heated by electric resistance heating, microwave heating, or a combination of methods. The incoming CO and/or H2 also can be preheated to simulate a potential utilization of recovered heat. The iron oxide weight and temperature can be monitored during an entire reduction period. A series of reduction experiments have been conducted. The results are presented and discussed.

Jan 1, 2006

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By Stefan K. Schwank

The paper describes the two foundation techniques - mini piles and postgrouted bored piles. The mini pile system is presented with its design and installation parameters, especially the drilling technique. Two case histories demonstrate the application under extremely limited space and traffic conditions and the required modifications of the equipment. After the description of the postgrouted bored piles and its grouting technique, the paper gives a comparison of postgrouted piles and standard piles on a large basic test in Germany. The Brooklyn Queen's Expressway, N.Y., case history shows the application of this technique after redesign of the original proposal. 1. General Increasing requirements to improve existing foundations to carry additional loads and to increase the bearing capacity of bored piles leads to two new piling techniques: the mini-pile and the post grouted bored pile.

Jan 1, 1991

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

Hydraulic fluid power systems are advantageous whenever power output must be accurately and safely controlled. The load movers, cylinders, jacks, rotary actuators and hydraulic actuators in these systems can be made to smoothly and accurately start, stop, reverse, hold position or move steadily under heavy and variable loads or torques. Because hydraulic systems are simple, compact, reliable, and low cost compared to other power methods and because they can deliver controlled power anywhere on the machine to which a hose can be routed, they are a pan of almost every type of machine found on a coal mining section. Some of the functions they perform are positioning drill booms, driving drill pots on roof bolters, positioning curter booms, raising, lowering, and swinging conveyors, driving conveyors on continuous miners, raising, lowering, and applying sustained loads to longwall roof supports, and advancing the face conveyor and roof supports in longwall mining operations.

Jan 1, 1982