Search Documents

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By David Siskind

The authors studied small seismic exploration blasts for vibration characteristics and effects on structures in Mexico. Obtained were 267 three-component recordings of ground vibrations and structure responses from 62 test blasts at six single-story masonry structures. Charges were 4.55 kg (10 lb) of Vibrogel expolsive at depths of 20 and 30 meters. Initial blasts were 240 meters distant and proceeded towards the structures to as close as 5 meters. All blasts were in soil media in two basic types of terrain, low saturated areas and upland dry areas. Structural inspections were before, during, and after the test blasts.

Jan 1, 2002

By Enrique Albarrán, Julian Hernández

"In 1942 The “Presa Mixcoac” dam was built, along with 15 other dams, to control the rain fall waterin the mountains west of Mexico City. Mexico City’s population at that time was around 1.5 millionpeople, and the dam was way out of the city."

Jan 1, 2016

By John B. Tieder

Arbitration is a legally recognized alternate litigation for the resolution of civil disputes. The parties agree, either before or after a dispute arises, to submit that dispute to an independent third party for resolution. The decision of that third party is binding on the parties. A decision of an arbitral tribunal, typically referred to as an "award," cannot be reviewed by a court except on very limited grounds, such as fraud. See, e.g., Va. Code 8.01-581.010. Indeed, an arbitral award is typically less subject to judicial review than the decision of a trial court, whose decisions are almost always subject to appellate review as a matter of right. Arbitration is typically the result of a contractual agreement between the parties to submit disputes to arbitration. On occasion, arbitration can be required by statute. For example, the California Department of Transportation requires the arbitration of all disputes arising under its contracts. Public Contract Code, Article 7.1 (§§10240-10240.13). There may be a question whether statutorily required arbitration is truly arbitration or an administrative law disputes resolution procedure. The significance of the difference is that the decisions of administrative law bodies are typically reviewable by a court of law as a matter of right while, as set forth above, arbitral awards are almost never reviewable.

Jan 1, 1988

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

By Murray Pearson, Jack Murray

"The danger of autoclaves lies in the high temperatures and pressures that exist in autoclave vessels. The usage of autoclaves will continue to expand in the mining industry because of their efficiency and environmental friendliness. But increasing attention must be paid to ensuring their safety. Safety Instrumented Systems (SISs) play a critical role in autoclave plants by detecting potentially dangerous conditions, taking the plant to a safe state, informing the operator about the plant status and the cause of the trip and expediting safe plant restart. The SIS should ideally be fully integrated with but functionally independent of the Basic Process Control System (BPCS) and provide redundant logic solvers to increase safety and plant availability while reducing spurious trips.INTRODUCTIONWikipedia defines an autoclave as follows: “An autoclave is a pressurized device invented by Charles Chamberland in 1879 designed to heat aqueous solutions above their boiling point to process materials.” A typical autoclave system used in the metallurgical industry includes, besides the autoclave vessel, heat recovery (heater) vessels, high pressure positive displacement (HPPD) feed pumps, vessel lining systems, specialized internals and components, agitators, pressure letdown or flash vessels, isolation and control valves, over 2,000 I/O points and related instrumentation, and emergency relief systems."

Jan 1, 2009

By Yongjun Peng, Yufan Mu, Rolf A. Lauten

"Chalcopyrite, a major source of copper, is commonly found associated with iron sulfides, particularly pyrite. The separation of chalcopyrite and pyrite by flotation is difficult due to the galvanic interactions between pyrite and chalcopyrite during grinding and flotation. Galvanic interactions may cause oxidation and dissolution of chalcopyrite, copper activation of pyrite and the formation of hydrophilic iron hydroxide coating. The overall effect may change the floatability of the components and lead to the misplacement of pyrite into chalcopyrite concentrate. The objective of this study was to investigate the effect of lignosulfonate-based biopolymers on the depression of pyrite in the flotation of chalcopyrite with xanthate as collector and the mechanism responsible for the selective depression of pyrite. The flotation results showed that biopolymers depressed the flotation of both copper-activated pyrite and chalcopyrite in single mineral flotation although to different extents. In the flotation of mixed mineral systems, biopolymers significantly depressed pyrite flotation but had a less influence on chalcopyrite flotation. The selective depression of pyrite by biopolymers was due to the preferential adsorption of biopolymers on copper-activated pyrite surface. Galvanic interactions between pyrite and chalcopyrite surfaces promoted copper activation on pyrite. Presence of cuprous ions on pyrite surface favored biopolymer adsorption by the formation of a complex between the cuprous ions and biopolymer molecules. The same galvanic interactions also facilitated chalcopyrite oxidation leading to the formation of hydrophobic polysulfide that enhanced the hydrophobicity on chalcopyrite surface. The biopolymer structure controlled the depression effect. The results showed that the biodegradable biopolymers are promising depressants for pyrite.INTRODUCTIONCopper sulfide minerals, such as chalcopyrite (CuFeS2), bornite (Cu5FeS4), chalcocite (Cu2S) and covellite (CuS), are the major mineral source for copper. They are often found finely interlocked with iron sulfides, especially pyrite (FeS2) (Owusu, Brito e Abreu, Skinner, Addai-Mensah, & Zanin, 2014). Pyrite, as the most abundant sulfide mineral, is perceived as gangue in most cases and should be removed from the associated sulfides to minimize its contamination of the copper concentrate (Owusu, Addai-Mensah, Fornasiero, & Zanin, 2013; Wang & Forssberg, 1991). The commonly used strategy to remove pyrite is flotation (Wang & Forssberg, 1991)."

Jan 1, 2016

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987

The Mineralogical Researches of Gold Ores and Technological Products at Operating Factory in Olympiada Mine (Russia)

Sep 13, 2010

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Desiree Willis

One of New York City?s largest subway projects is under way 43 m (140 ft) beneath the surface of downtown Manhattan. The East Side Access project, more than 30 years in the making, was halted after a partial excavation in the 1970s due to a lack of funding. The project, once dubbed the ?Tunnel to Nowhere,? has been revitalized into a groundbreaking subway line that includes unique tunnel boring machines (TBM), construction methods and muck removal systems. Project overview The East Side Access project involves construction of a new 6.7-km (4.2-mile) subway line needed to relieve heavy traffic congestion between the boroughs of Queens and Manhattan. The line will serve approximately 160,000 commuters daily between Grand Central and Sunnyside rail stations. Manhattan and Queens will be connected under the East River by the 63rd Street tunnel, a submersed double-decker tube. The submersed tube consists of reinforced concrete sections barged in place on the riverbed. The tube contains operational subway lines on the top deck, while the bottom deck (the ?Tunnel to Nowhere?) will become operational when the East Side Access project is completed in 2013.

Jan 1, 2008

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.' A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler's establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

IN a mine with any considerable output the economical handling and transport of ore underground is a matter of prime importance, and in the design or lay-out of a trucking system the question of what form the points and crossings are to take should be one of the first considered. Trucks may be moved from one line of rails to another by the following means: by flat sheets, with which may be coupled turn-tables, or by points and crossings. The latter class may be further divided into fixed and movable points.Flat sheets and turn-tables, owing to the time and skill needed by the trucker in using them, are seldom of great value with large tonnages, unless for purely temporary work, and the choice narrows down to one between fixed and movable points andcrossings. Both systems have their disadvantages - movable points being liable to jamb with dirt and get out of order, whilst with fixed points trucks may sometimes run over the points and capsize, or go on to the wrong line, though this is not of frequent occurrence. On the other hand. the fixed points are simple, easily laid, and strong, and there is no necessity for the trucker to work any levers, the truck being guided on to its new direction by screwing.Cast-iron points and crossings were first introduced into the North mine during the opening-up of the 950-ft. level, and the first arrangement was designed for a double turn-out in the main crosscut. Since then both the points and crossings have beenmodified several times, and it may be interesting to briefly outline the various forms through which they have passed, showing the reasons for the retention of some features and the rejection of others.

Jan 1, 1915

By J. E. Murphy

The u.s. Bureau of Mines investigated electrode designs for electrowinning lead metal from a LiCl-KCl-PbCI2 electrolyte at 4500 C. The major objective of this investigation was to decrease the energy requirement for lead electrowinning. Electrolysis was performed in a bench-scale cell using several graphite electrode assemblies. Such parameters as electrode spacing, current density, and chlorine gas removal from the anode were investigated in the bench-scale tests. An optimum electrode assembly, termed the sawtooth design, was scaled up and operated at 3,000 and 4,000 A. The sawtooth electrodes operating at 3,000 A produced lead for 0.66 kW·h/kg. The electrodes were constructed by cutting large triangular grooves in the electrode surfaces. The electrodes were placed together such that the triangular peaks of one electrode projected into the triangular valleys of the other electrode. Chlorine did not build up on the anode with the sawtooth electrodes.

Jan 1, 1991