Search Documents

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By Lise Chénard

El presente texto señala los lineamientos del proyecto REFORMIN, así como su repercusión en la dinámica de promoción de la industria minera. REFORMIN surge en el 2001 como un proyecto bilateral entre Canadá y Bolivia, cuyo financiamiento proviene de la Agencia Canadiense de Desarrollo Internacional (ACDI). Su finalidad es apoyar al Viceministerio de Minas, facilitándole el acceso a la pericia canadiense para lograr una gestión más sana y eficaz de los recursos minerales del país. Para ello, se basa en los principios fundamentales tales como: mejora de la gestión del medioambiente minero, apoyo a la prevención y gestión de conflictos sociales en las comunidades mineras, a los mineros artesanales y a la promoción de los recursos minerales del país, -en tanto benefician al desarrollo de la industria minera en un contexto de mercado globalizado.

Apr 22, 2003

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

Recently, work was carried out by the Shotcrete Working Group to study anisotropy in steel fibre reinforced shotcrete using strain-controlled, compressive strength testing methods. The shotcrete materials used and specimen preparation procedures as well as testing methods are described. The test results are discussed and it is concluded that, because of the anisotropic nature of fibre reinforced shotcrete, it may be worthwhile investigating the degree of such anisotropy in practice using strain-controlled, strength testing techniques.

Jan 1, 2001

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By H. Kinilakodi

In 2008, the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using a sample of 103 mines with 2008 and 2009 data, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performances as compared to large and medium-sized mines.

Jan 1, 2011

The Menominee Range of northern Michigan was a major producer of direct shipping iron ore for nearly a century. When the last underground mine on the Range ceased operation in 1978, it marked the end of an era. For since the start of mining in the early 1880's the district has gone through a Lull cycle from the start-up of mining through close-down. During this period over 200 million long tons of iron ore were produced and shipped from nearly 100 mining operations. This development and production spanned the time from when the United States advanced from an essentially rural-agriculatural society through the industrial revolution and into the beginnings of the computer and space age. There are many lessons that can be learned from such a rich history. This report attempts to provide ouch a lesson. Through the use of case histories, deficiencies in past mining practices and mine closure procedures that have resulted in current mine related problems are documented. These problems -an be grouped into three areas; 1) subsidence 2) hydrological or drainage problems and 3) problems related to inadequate mine shaft sealing and capping practices.

Jan 1, 1983

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

"AQUILA Mining Systems Ltd. is a Canadian company that designs and develops monitoring, control and navigation systems for the surface and underground mining industries. In 1992, AQUILA Mining Systems began the development of technology for monitoring, controlling and positioning mobile mining equipment. In 1993, AQUILA completed its first field test with GPS receivers onboard ablasthole drill, and thus demonstrated the viability and strategic relevance of this technology in surface mining. Since then, AQUILA has installed GPS-based technology on drills and shovels in several Canadian mines. This paper will review the development of these systems and discussthe benefits the mining industry could realise through their production implementation."

Jan 1, 1997

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

By A Rantala, K Aberkrom, O Haavisto, P Blanz

More complex ore bodies with lowering grades increase the challenges of maintaining high throughput, energy efficiency and required particle size for optimal downstream processing in grinding circuits. Continuous and often rapidly changing characteristics of the mill feed requires constant focus to operate the circuit at optimal level. Modern process instruments, on-line analyzers, monitoring and process control systems provide attractive and managed options to increase the circuits’ capability to respond to the challenge, often in phases and in rather short time period. Furthermore, well instrumented and performing base level automation in the grinding circuit enables advanced process control (APC) strategies that utilize measurements from the whole circuit to stabilize and optimize production. In this paper alternatives for incorporating process measurements and controls to typical grinding circuits are proposed. The expected benefits to throughput, availability, energy efficiency and particle size stability are described in recent case examples.CITATION:Rantala, A, Blanz, P, Aberkrom, K and Haavisto, O, 2015. Increasing grinding circuit robustness with advanced process control, in Proceedings MetPlant 2015, pp 129–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Cliff McCartney, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research to evaluate and improve remote mine seal construction technology for mine fire control and suppression. The main focus of this work is to develop reliable technology that will remotely seal a mine opening from floor-to-roof and rib-to-rib. NIOSH, in partnership with Strata Mine Services Inc.1, is evaluating the capability of a two-component phenolic foam-based product, called Rocsil®1, that is intended for cavity filling, air and gas sealing, and consolidation of highly fractured strata. Rocsil® can be rapidly applied, has a quick cure time, a high expansion rate, good compressive resistance and excellent anti-static properties. When the resin and catalyst are mixed, an immediate foaming reaction occurs followed by rapid expansion up to 30 times the original volume. By virtue of its fire-resistance properties, Rocsil® foam has application for sealing underground mine areas undergoing heating from spontaneous combustion and it could be useful for remote mine seal construction to aid in mine fire control and suppression. This paper presents an overview of remote mine sealing technology, introduces the use of Rocsil® foam for remote mine seal installations, offers a case study of the use of this rigid foam material to remotely construct a temporary in-mine seal and discusses technology improvements. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P2O5 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012