Search Documents

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By Diego Pinheiro Aun

Neste trabalho, foi investigada a influência da textura de fitas de NiTi superelástico no início do processo de cristalização de um revestimento de TiO2 flexível. Foram utilizadas a calorimetria diferencial, cartografia Raman e difração de raios X para o estudo. Foi mostrado que existe uma influência significativa da textura do substrato no crescimento de grãos de anatase e rutila no filme de TiO2. Amostras com menor rugosidade apresentaram grãos mais desenvolvidos para todas as temperaturas de cristalização. Mostrou-se também que o substrato de NiTi promoveu a formação de TiO2 rutila em temperaturas abaixo daquelas observadas para a cristalização de pós.

Aug 16, 2017

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By N. Singh

Merensky Reef is mined extensively within the Bushveld Complex. In previously mined-out areas on the Merensky Reef horizon there are pillars, potholes and remnants that have not been mined. These unmined blocks of ground on the Merensky Reef horizon can influence the mining of the underlying UG2 Reef. The extent of the influence will depend on the size of unmined ground and the middling between the two reef horizons. This paper quantifies the influence of partially extracted Merensky Reef on mining of the UG2 Reef, and aims to provide recommendations for mining strategies, as well as regional and local support to achieve efficient and safe extraction of the UG2 Reef, for various middlings beneath the Merensky Reef horizon. In some cases it was found that relatively shallow UG2 Reef mining could encounter conditions similar to those experienced in deep and ultra-deep mining environments.

Jan 1, 2005

Influence of Frothers on Bubble Shape and Velocity Close to the Generation Point

Sep 13, 2010

A Process for the Flotation of Chrysocolla

Sep 13, 2010

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By H. C. Seeber

When considering all the aspects of a viable mine plan, it is important to estimate the accurate cost of mine ventilation, which varies as a function of airway dimensions, fan selection and ventilation network. Optimization of the overall elements of ventilation design can lead to very significant cost savings when capital and operating cost savings are considered in combination. This paper will describe a methodology, whereby ventilation costs can be minimized by optimizing the ventilation aspects of mine design and fan selection, by providing a brief description on ventilation theory and the factors which affect ventilation operating and capital costs.

Jan 1, 2002

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. A potential method of minimizing pollution from radio-active nuclides, principally radium 226, in uranium mill waste streams is to reuse the waste solutions within the mill. Such reuse of waste solution in the Kerr-McGee Shiprock-type process was investigated in the laboratory. The Shiprock mill employs a two-stage acid-leaching process for dissolution of the uranium, countercurrent decantation for liquid-solid separation and washing, and organophosphorus solvent extraction for recovery of the uranium and vanadium from solution. The simulated use of barren raffinate instead of fresh water in the mill circuit was carried through a laboratory campaign of 28 interlocked leaching, washing, and solvent extraction cycles. About 99 percent of the uranium and 91 percent of the vanadium were dissolved from the are, Washing efficiency in the thickener circuit averaged about 99.5 percent when the pulp was washed with enough barren raffinate and makeup water to recover 2.5 tons of pregnant solution per ton of ore. The only solution discarded was that contained in the washed and thickened leach residue. A buildup of salts due to recycling of solutions did not adversely affect operation of the washing circuit.

Jan 1, 1962

Predicting the future is a task that should always be delegated. If that is not possible, then stating your views confidently, but retrospectively, is preferable. Hindsight encourages clarity of thought and sharpens perception. When all else fails one can look back into history and see the trends, evaluate the current situation and project it a little way into the future - in this case 10 years. In exploration the rate of change has been increasing over the past 20 years. With expected developments in technology, legislation, and their sociological impacts, we will see such rapid change over the next decade as to make us uncomfortable, unless we are prepared for it. &nbsp; The social obligations of our industry also have changed enormously over the past 20 years and are still changing. This will lead to further changes in the way we conduct our business if we wish to stay in business. As exploration technology improves, a further dimension is added by the expectations of the communities in which we operate. This extra dimension needs to be quantified so that we not only keep up with current developments but also get ahead of the game. This paper is based on the New Zealand experience, some of which will be familiar to mineral explorers in other countries.

Jan 1, 1997

By A C. Edwards

The Mongol-Okhotsk belt consists of detached fragments of the Circum Pacific fold belt which have been trapped within the Mongol-Okhotsk fold belt. In its western part, the structures of the belt form an east-facing loop that is not connected with the other orogenic structures of Central Asia. In the eastern part of the belt (the Mongol-Okhotsk suture zone) the terranes form a zone between the Siberian craton to the north and the Bureya composite terrane to the south, that is linked with the Circum Pacific belt. The accretionary terranes, together with their Precambrian backstops, form a series of consistently-stacked, paired units that are bounded by northwest and north trending sinistral strike-slip faults. The ages of the rocks forming these accretionary complexes vary from Late Precambrian - Carboniferous in the west to Cambrian - Jurassic in the east. The terranes developed due to a progressive westward stacking of the accretionary complexes during the process of accretionary growth. The magmatic rocks young eastward indicating that migration of the magmatic front of the arc followed the eastward growth of the accretionary complexes. The accretionary terranes may be differentiated by their Paleozoic lithological assemblages. Only the Selemdzha, Niman, and Kerbi terranes located in the eastern part of the Mongol-Okhotsk suture zone contain significant amounts of black shale, and it is these terranes that host the bulk of the hardrock and placer gold mineralisation that is present within the suture zone. Gold mineralisation is present both as vein style and disseminated mineralisation within structural duplexes.

Jan 1, 1999

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications., The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications.3/ The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009