Search Documents

Drilling and blasting are an essential part of most mining operations, and are commonly major operating cost centres. The effectiveness of blasting can have a significant influence on all subsequent activities, and hence overall operating costs. Drilling and blasting systems must be compatible with the overall mining method, to minimise total costs and ensure operational efficiency. Selection of suitable equipment and techniques requires an understanding of the total operation, plus current skills in specialised technologies. This paper examines the contribution of drilling and blasting to total costs, including the balance between capital and operating costs. The use of computer modelling is discussed, to demonstrate how blast performance and costs can be predicted and alternatives analysed. Case studies illustrate how cost savings can be made in operating mines, and alternative systems evaluated to optimise new projects.

Jan 1, 1990

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module (Fig. 1). The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information. Key for Fig. 1 A-Helium-3 neutron detector B-Wax moderator for neutrons C-Irradiation chamber D-Funnel for receiving ore E-Gate F-Transducers G-Biological shield for neutron source H-Transfer tube for neutron source I-Neutron source J- Microprocessor K-Accumulator for hydraulics L-Control panel M-Electro-hydraulic servo valve to control movement of the source N-Electro-hydraulic proportional valve to control movement of the gate O-Hydraulic power unit Irradiation and Counting Equipment Irradiation of the ore is achieved using a 1 X 10 7 neutron*s-1 californium-252 neutron source. The source is contained in an iron capsule and pneumatically transferred between the irradiation/counting and storage chambers. The irradiation/counting chamber possesses 12, 600-mm (24-in.) long helium-3 thermal neutron detectors embedded in an annulus of wax (Fig. 1). Two sets of six detectors are each interfaced to a preamplifier, amplifier and single-channel pulseheight analyzer system, and the two systems are connected to a scaler. A special timing unit controls the transfer of the source and the on and off switching of the detector assembly, in sequence with the movement of the source. Results and Discussion In the experimental demonstration, using the 107 neutron.s-1 source, a 10% uranium ore was measured to ± 10% (2o total error) in 10 cycles and ±6% (2o) in 100 cycles. Since a larger source was not available, it can be statistically predicted that a 109 neutron-s-1 source could be used to measure a 0.1% ore to ± 10% (20) in 10 cycles. The uranium can occur as discrete nonhomogeneous particles in the ore, and the error caused by such a distribution of particles is ± 4% (2o), as determined by

Jan 1, 1984

By M. K. G. Whateley, W. Hatton

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 20pp., 31 refs. Estimates of coal tonnage on UK open cast mining sites often vary from the recoverable tonnage. This is because the estimates depend on the geological variability of the coal measures. Geological parameters, such as thickness, quality and disturbance of the seam, have a direct control upon this variance. Risk analysis techniques have been applied using commercially available software to combine each parameter's variability into a cumulative variance, resulting in a tonnage distribution. Sensitivity modelling has also been used to identify the geological parameters which have the largest influence on the variance of the simulated tonnage distribution. An understanding of the relationship between the tonnage and geological variability has helped to focus exploration more efficiently. A cost to risk relationship can now be monitored, helping management to avoid negative consequences on site

Aug 1, 1995

By A. D. Davis, C. J. Webb, C. S. Johnson, J. L. Porter

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM) property. The mine produced primarily lead and zinc during the first half of the twentieth century. The BLM has expressed concern about acidic drainage as well as elevated arsenic levels in tailings and waste rock at the site. The mine site was evaluated for remediation in 1998 and 1999. Recent reclamation and remediation work included substantial regrading of waste rock, removal of material where metal loading were of concern, and re-routing of drainage from an adit. Trenching at the site shoed a greater volume than originally calculated during site characterization. Material was removed to a repository that was constructed at a nearby drainage divide. Because of physical hazards, the BLM has decided to remove some historic structures. However, a search of mine records and an inventory of archival materials were complete to preserve the history of the site.

Jan 1, 2002

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By W. T. Wertman

LABORATORY research has been started at the Bureau of Mines Morgantown Petroleum Research Laboratory, Morgantown, Va., to investigate the possibilities thermal-recovery methods for producing crude oils of high API gravity found in oil reservoirs of the eastern United States. This bibliography on thermal methods of oil recovery was compiled as a part of the work. Crude oil discoveries to December 31, 1958, in the United States were estimated to exceed 270 billion barrels. Cumulative production of crude oil through 19.55 was about 60 billion barrels, and the American Petroleum Institute estimates that an additional 30.5 billion barrels are economically recoverable by present methods. On this basis, about two-thirds of the oil that has already been found can be classified as economically unrecoverable for lack of a satisfactory method. The rap icily rising costs of proving new deposit; of domestic petroleum, the lack of new discoveries of large oilfields in the united States, and I he growing demand for crude oil have caused an acceleration of research to develop new or improved methods fur producing "unrecoverable" oil in known reservoirs.

Jan 1, 1960

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

By J. R. Thoenen

"The curtailment of imports of foreign potash during the World War directed attention to the necessity of establishing a domestic source of potash for fertilizer, and considerable study has been given to the subject by Government bureaus, research organizations, and private individuals. These studies have covered all known sources of potash, and among them the extensive greensand deposits of New Jersey in which the potash content is found in the mineral glauconite have been investigated.Several hundred patents have been obtained covering processes for the extraction of potash from siliceous minerals, but up to the present time none have proved successful on a large commercial scale.When the investigation of the potash deposits of Texas was started by the Federal Government, the laboratory study of the drill cores was assigned to the Nonmetallic Minerals Experiment Station at New Brunswick, New Jersey, with the object of ascertaining a possible commercial method of utilization.The purpose of this preliminary study was to investigate existing literature and previous investigations to ascertain the extent and availability of the deposits, the extent of commercial success so far attained in potash extraction, the most promising known methods and by-products obtained from them, probable markets, and possibility of competition with foreign potash, and by a study of these data to determine whether further chemical engineering analysis and laboratory investigation were warranted.As the study advanced it became evident that adequate reserves of green-sand were available for many years supply. and that whereas many processes had been patented few had been tried commercially. In collaboration with former private and Government investigators these patents were first divided into two"

Feb 1, 1929

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, how- ever, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non- metallic inclusions seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1951

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976

By Inn-Joon Park

Major problems associated predicting soil-structure interaction behavior are based on the fact that soil is neither homogeneous nor elastic and soil properties are spatially variable. There also exist significant coupling problems between the behavior of the structure and geologic media. When designing foundation or other geotechnical structures, the load transfer between the soil and structure takes place at the contact surface. This surface is called the interface. The behaviors of interface play an important role in the load-deformation response of soil-structure interaction systems. The purpose of this study is to develop improved model for simulation of saturated sand-steel pile interface behavior based on a general concept, called the disturbed state concept (DSC), which can characterize the behavior of saturated soils under dynamic loads. In this study, the Disturbed State Concept (DSC) constitutive model is calibrated and modified for steel pile-saturated sand interface and interaction by using the continuous hardening model for relative intact (Rl) state and the critical state model for the fully adjusted (FA) part in the saturated sand material. The general formulation for implementation has been developed. Then, the DSC model with modification for interface and saturated sand is implemented in finite element program based on the generalized Biot's theory. The interface tests under one-way monotonic and two-way cyclic loading and cyclic triaxial tests are executed for defining the parameters for interface and surrounding soils. Based on these parameters, steel pile-saturated sand interface and interaction are numerically simulated using the finite element program modified in this study. The DSC predictions show improved agreement with the observed results from laboratory test.

Jan 1, 2002

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006