Search Documents

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By Jr .. Ebbley

The investigation of mine shafts and underground workings at Leadville, Colo., was started in May 1946 and recessed in November 3, 1946. Thirty-eight shafts and connecting accessible underground workings, comprising about a third of the accessible shafts in the district, were investigated. The Leadville district, a former important producer of lead and zinc, was considered by the Bureau of Mines to be capable of bolstering 'the waning domestic output of .these important metal. Accordingly, the investigation was initiated for the purpose of. .obtaining more definite data on sulfide and oxide reserves, evidence to justify completion of the Leadville drainage tunnel, representative large samples of the complex oxidized and mixed ores for testing to determine methods, beneficiation factual data to be supplied to property owners in order to stimulate production, and to determine the more favorable areas for development by the Bureau.

Jan 1, 1949

By Qingxia Liu, Mingbo Zhang, Hongbo Zeng

The shortage of freshwater has been a major challenge for mineral flotation in arid areas. When using high salinity water, certain electrolytes are detrimental to flotation while others can improve the flotability of minerals. In this paper, the flotation behaviors and contact angles of pyrite in both Milli-Q water and high salinity water were investigated using different collectors at various pH levels. Results show that the thionocarbamate has a less affinity to pyrite in different solutions under mildly alkaline conditions as compared with potassium amyl xanthate (PAX) and N-isopropoxypropyl-N’-ethoxycarbonyl thiourea (iPOPECTU). At high pH levels, the slime coating on pyrite surfaces, which is caused by colloidal precipitates of magnesium and calcium ions in seawater, was confirmed by SEM, EDX and in-situ zeta potential measurement. The slime coating of colloidal precipitates on mineral surfaces led to low recovery of pyrite at high pH levels. The study of flotation behavior of pyrite in high salinity water improves our fundamental understanding of mineral flotation in seawater.

Jan 1, 2015

By Glenn C. Reed

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to the Department of Interior agencies and to others concerned with planning the proposed Federal power development within the Missouri River Basin . The present report has been designed to permit public distribution of factual data obtained . The field investigations were made during the late fall of 1947 and the summer of 1948. Information on mineral occurrences in several areas in Sweet Grass County also are included in this report because of their close proximity to Park County . Practically all known metallic mineral deposits within Park County were investigated ; some nonmetallic mineral deposits also were investigated. The investigations of the metallic mineral deposits in Park County cannot be considered complete ; some long inactive mines and prospects on which little or no information is of record may have been missed . Many of the underground openings , especially at the long inactive properties , no longer are accessible ; consequently , much of the information regarding history their and development necessarily has been obtained from available Federal and State publications .

Feb 1, 1950

By Eduardo Macedo Junior

O presente trabalho descreve o desenvolvimento de uma nova especificação para a Linha de zincagem numero 3 (LZC#3) da Companhia siderúrgica nacional (CSN), de grande demanda e aceitação, alta produtividade e foco nos requisitos do cliente que tangem qualidade superficial e características metalúrgicas (resistência mecânica) em aços para atendimento do mercado Norte-americano. Este novo produto tem como característica o ciclo de recozimento com velocidade alta para obtenção de microestrutura 100% encruada na saída do equipamento e limites de escoamento e resistência acima de 500 MPa. A combinação dessas características do produto junto com as características do processo tornou a especificação “ASTM-A653MSS80CL1” um grande desafio para garantir qualidade superficial sem comprometer as propriedades mecânicas especificadas assim como a integridade do equipamento. O baixo custo de produção associado a alta produtividade desse produto fazem da especificação “ASTM-A653M-SS80CL1” um produto de extrema importância para a estratégia adotada pela CSN, mantendo dessa maneira sua competitividade no mercado Norte-americano e garantindo capacidade máxima de produção do seu equipamento em tempos de retração do mercado interno.

Aug 17, 2017

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

By Ogden Tweto

The Leadville district, on the west flank of the Mosquito Range in central Colorado, has produced silver, zinc, lead, gold, and minor metals valued at $512,000,000. The ore deposits are in a sequence of dolomites and quartzites, Cambrian through Mississippian in age and about 500 feet thick, which is extensively intruded by porphyry sills, dikes, and plugs of Tertiary age. The sedimentary rocks and sills dip about 15°E and are broken by many faults, which are predominantly of nearnorth trend and downthrown to the west. The ore deposits are principally blanket or manto replacement deposits, but in the eastern part of the district many veins occur also. The replacement deposits are largely confined to three dolomite units in the stratigraphic sequence. Of these, the uppermost or Leadville Dolomite is the most productive. Most ore bodies are on the underside of porphyry sills and, particularly, beneath sills that occupy unconformities. Many replacement bodies have vein roots or branch from veins. The veins occupy faults and are productive mainly in the section of quartzites and dolomites and included sills. The primary ores consist principally of pyrite, marmatitic sphalerite, and galena but locally contain chalcopyrite, silver minerals, bismuth minerals, and gold. Principal gangue minerals are manganosiderite and jasperoid. The ore deposits have a crude zonal pattern centered around an intrusive center at Breece Hill, which evidently influenced ore deposition thermally. The ore deposits were oxidized to depths of several hundred feet in Miocene time. Bonanza ores mined in the early days were characterized by cerussite, cerargyrite, and embolite. Later, zinc carbonate ores were identified and mined on a large scale. The Leadville district is a complexly faulted and intruded area at the intersection of major fault systems trending N20°W and N15°E in the Mosquito Range. The intensely fractured area evidently localized igneous intrusion and subsequent mineralization. Ore solutions rose on many of the faults in the area, presumably from the same source as the porphyry magmas. Movement on these faults continued into the Pleistocene, displacing ore bodies, oxidation zones, Pliocene sediments, and glacial deposits.

Jan 1, 1968

By F. S. White, E. L. Kinsella

THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to ' quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,1 showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.2 Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a 1/4-in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontally at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 1/2 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4 1/2-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1952

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By Jedson Alessandro Damasceno

Atualmente, a maioria dos pátios utilizam recuperadoras com roda de caçambas para remover o minério das pilhas de estocagem. Tipicamente, estas máquinas são operadas manualmente, com todos os movimentos controlados por operadores, o que faz com que o processo seja totalmente dependente de sua experiência, tornando difícil manter o processo em operação ótima. Para alcançar uma melhor performance, foi implementado um sistema automático que controla todos os movimentos de recuperação. Um importante desafio encontrado durante a construção dessa solução foi a de estimar a taxa de recuperação em tempo real, uma vez que esta informação é essencial para o algoritmo que controla o movimento de giro da máquina. Uma medição real dessa taxa está disponível, mas, a balança localizada na lança fica distante da roda de caçambas. Em outras palavras, a medição real está disponível com um grande atraso (aproximadamente 13 segundos). Este delay é inaceitável para o algoritmo de controle que necessita de uma medida em tempo real da taxa de recuperação na roda de caçambas. Diante disso, foi necessário implementar um sensor virtual. Este sensor foi implementado usando um sistema neuro-fuzzy para estimar a taxa de recuperação em tempo real utilizando outras variáveis disponíveis, tais como a pressão na roda de caçambas e medidas de penetração obtidas por radares. As estimativas obtidas ficaram muito próximas dos valores reais, e este sensor pôde então ser utilizado pelo algoritmo de controle.

Aug 17, 2017

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By Morton Corn

The U. S. Federal Coal Mine Health and Safety Act of 1969 placed limits on the permissible concentration of airborne respirable coal mine dust. Evidence exists which suggests that the effects on health of respirable coal mine dust may depend on both host factors and dust properties other than concentration. Dust particle size, shape, density, specific surface area and chemical composition are among the dust parameters of interest in an epidemiological investigation of coal workers' pneumoconiosis and coal miner exposure to mine dust. The purpose of this investigation was to develop and demonstrate the feasibility of techniques to determine selected properties of respirable coal mine dust. An approved underground horizontal elutriator which samples air at 36 cfm was designed, fabricated and utilized in this study to collect respirable coal mine dust in three mines representing the Pittsburgh, Lower Freeport and Lower Kittanning coal seams. Analytical procedures for measurement of respirable dust sample particle size, density, random projected area, total surface area and chemical composition are presented. Results of analyses of three samples collected in each mine are presented. Up to five full work shifts of sampling were required to accumulate approximately five grams of respirable coal mine dust in each sample. Statistical tests were applied to determine the significance of differences between properties of dust samples collected in the same mine and between arithmetic mean values of dust properties representing three samples collected in each mine. A comparison was also made between

Jan 1, 1972

By E. P. Buxton, W. P. Yant, G. W. Jones

"Introduction. The data obtained in recent research work by the Bureau of Mines show that the analysis of the gases dissolved in underground waters may be used by the prospector or geologist as an additional aid in discovering new oil or gas fields. The hydrocarbons present in the water serve to indicate whether oil or gas sands exist in the region through which the waters have passed. A portable field apparatus has been developed by the bureau which can be used for removing and analyzing the gases dissolved in the waters. This apparatus and the method of u are described in this paper. Results are given of analyses made on waters from various localities, and the significance of these waters with reference to the detection of oil and gas.Any liquid, with the exception of mercury, if permitted to come in contact with eases or vapors will absorb a definite amount thereof. This action depends on the following factors: (1) The kind of gas; (2) the percentage composition of the eases in contact with the liquid; (3) the pressure of the gas; and (4) the composition and temperature of the liquid. For our present purpose it is only necessary is consider two of these factors - namely, the gas or vapor (natural gas and light petroleum vapor), and the liquid (water).If water of underground origin traverses a gas or oil sand it will absorb a definite quantity of hydrocarbon vapors, and will carry these vapors to the surface when tapped by a well. When the water is exposed to the air at the sur¬face, the eases and vapors will be given off and their place taken by oxygen and nitrogen from the air. Therefore, an analysis of the gases in waters reaching the surface from an underground source should be of value in determining whether these waters have traversed or came in contact with hydrocarbon-bearing strata. With the apparatus herein described it is possible to determine whether the vapors are mainly of natural gas on sition (methane CH1) and ethane (C2H6 ), or are come posed mostly of heavier petroleum vapors (ethane, propane (C3E8) and buttane (C4H10)."

Nov 1, 1923

By Michael Zurowski

This paper traces the history of International Mogul's assessment program on the Lake Ainslie barite-fluorite deposits of Cape Breton Island. The geology of the area is outlined, and the main vein systems described. The geophysical and geochemical exploration techniques employed are explained, the metallurgy of the ore is covered, and the market prices and economics of operation are described.

Jan 1, 1972

By D. B. Taliaferro, Thomas Jennings, C. M. Keithly

"INTRODUCTION This report describes the methods of development and operation and gives the results of controlled water injection into oil sands in Illinois. It is the third of a group relating to water-flooding operations in various States; previous reports have covered projects in Oklahome 5/ and Kansas.6/ Systmatic water flooding has been in progress, in these States, for more 10 years. In Illinois the Tide Water Associated Oil Co. has been injesting water into one or two wells on each of five leases in the Robinson Acknowledgments This study was made under the general supervision of R. A. Cattell, chief engineer, and H. C. Fowler, assistant chief engineer, Petroleum and Natural Gas Division, Bureau of Mines, Washington, D. C., and N. A. C. Smith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.The cooperation of the operators who are conducting water-flooding projects and who have made this report possible by furnishing data on their operations is gratefully acknowledged. The writers are grateful also to the following members of the Bureau of Mines for assistance in preparation and criticism of the manuscript: C. J. Wilhelm, Franklin, Pa.; and Gustav Wade, R. E. Heithecker, and Peter Grandone, Bartlesville, Okla. The illustrations were prepared by Helen Cramer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla."

Aug 1, 1944

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By F. Ikumapayi

Hydrogen peroxide production was measured during the grinding of a complex sulfide ore, and its oxidizing effect on solid surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) with diffuse reflectance attachment measurement. In turn, an attempt was made to correlate the formation of hydrogen peroxide, surface oxidation and sphalerite flotation. Additionally, in order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the effects of major components of calcium and sulfate species present in recycled process water and the effect of temperature on sphalerite flotation were investigated through bench-scale flotation tests using complex sulfide ores. The significance of process water species in flotation was studied using tap water, process water and simulated water containing calcium and sulfate ions. Formation of hydrogen peroxide was revealed during the grinding of the complex sulfide ore, and its formation was counteracted by diethylenetriamine (DETA). The FTIR spectrum of the pulp solid fraction showed varying degrees of oxidized surface species, which are related to the concentration of H2O2 analyzed in pulp liquid. Bench-scale flotation using two different complex sulfide ores showed that sphalerite recovery is better in process water than in tap water. Flotation results also indicated a varied recovery of sphalerite at different temperatures in either tap water or process water.

By Y. H. Cheng, D. M. Lewis, V. Castranova, M. W. Barger, J. K. H. Ma, J. Y. C. Ma, W. F. Xin

Bis-basic ethers off fluorene and fluoren-9-substituted derivatives such as tilorone have been reported to inhibit silica-induced fibrosis in rats. The potential antifibrotic potency of 2,7-bis (diethylamino) ethixy fluorine fluorenone (F-9-H.H), fluorenoxime (F-9-one), and fluorenol (F-9-ol) was F-9-axime > F-9-one ~ F-9-H,H > F-9-ol. Since the release of reactive oxygen species and growth factors from alveolar macrophages (AM) in response to silica exposure has been linked to the development of pulmonary fibrosis, the present study was carried out to determine the inhibitory effects of these compounds on rat AM activity in vitro. The following parameters were monitored: (1) cellular viability; (2) zymosan-induced respiratory burst activity (superoxide and hydrogen peroxide release, chemiluminescence, and oxygen consumption) of AM; (3) drug binding to AM; and (4) lipopolysaccharide (LPS)-stimulated interleukin- I (IL-1) release from AM. The bis-basic ethers, at 40 did not affect cell viability when incubated with AM for 30 min, but significantly inhibited zymosan-induced macrophage respiratory burst activity. The inhibitory effect of these agents was F-9-oxime > F-9-one ~F-9-H,H > F-9-ol. Binding of these drugs to AM was time and dose dependent, and exhibited the following binding affinity: F-9-oxime > F-9-one > F-9-H,H > F-9-ol. F-9- oxime was shown to inhibit LPS-stimulated IL-I release by AM in a dose-dependent manner. This inhibition of IL-1 release by AM cannot be explained as a decrease in viability. In addition, these drugs were also shown to impair human fibroblast proliferation in response to serum stimuli without impairing cell viability. These results indicate a positive correlation between drug binding to AM or other cell types and their inhibitory effects on cellular activities including oxygen consumption, superoxide release, hydrogen peroxide secretion, chemiluminescence, IL-I release, and proliferation. The ability of-these bis-basic ethers to modify AM and fibroblast functions in vitro suggests that further investigation of their reported antifibrotic potency in vivo is warranted.

Dec 1, 1996