Search Documents

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By David S. Yantek

Miners in underground coal mines experience prolonged exposure to high noise levels, often with A-weighted sound levels in excess of 90 dB. Field tests have shown that the continuous miner conveyor is a dominant noise source. This paper will identify the most significant noise-radiating surfaces on the continuous miner tail section using vibration levels and surface areas to estimate the sound power levels of each surface. In addition, using five test cases, this study will examine the effects of three engineering noise controls on the surface-averaged vibration levels and average sound levels measured with four microphones located two meters from the tail section. The noise-radiating surfaces of the conveyor’s tail section include the top and bottom decks, the sideboards, and the flex plates. Emphasis is placed on the changes in the estimated sound power levels in the 500 – 2500 Hz 1/3-octave bands since this frequency range accounts for 80-85% of the sound energy near the tail section. The results show that the bottom deck is the most significant noise radiator for the untreated miner. Installing a coated bottom deck reduces the estimated sound power level radiated from the bottom deck by 11 dB and the average sound level by 2 dB. Using a coated tail roller results in reductions of the estimated sound power levels for individual components from 1 to 4 dBand reduces the average sound level by 2 dB. Coating the slide plate has little effect on both the estimated radiated sound power levels and the average sound level. The test results indicate that modifications that reduce flex plate vibration and reduce energy transfer from the tail roller into the tail section will be effective in reducing noise when combined with a coated tail roller and coated return deck.

By M J. Shearer

An investigation into the reliability of the data being collected at the Mount Isa Mines site operated by Glencore in Queensland allowed on-site ventilation personnel to scrutinise pressure and volume measurements collected from the primary surface fans. The investigation effectively identified discrepancies being reported to the on-site remote monitoring system. The difference between the real-time and static measurements on the P63 RAR shaft identified that the in situ differential pressure transducer and piezo annubar system was not operating correctly. This indicated a deficiency of approximately 30 per cent reporting back to the remote monitoring software versus the live readings measured with the Pitot tube bomb and ALNOR AXD610 pressure micro-manometer.Constant monitoring of an operations ventilation network is imperative to ensuring that the underground atmosphere provides a safe and healthy workplace. Further benefits to real-time monitoring allows for the early indication of network failures and promotes increased availability. An innovative approach to out engineer and improve the existing measuring equipment from the 1970s was sought.The use of ultrasonics in the mining industry is not new with ventilation management systems (VMS) equipment available within the marketplace. The introduction and implementation of a reliable product for real-time monitoring was a challenge to overcome due to limited access and suitable measuring points within the mine. The available equipment on the market through mainstream suppliers was not suitable for the unique application required due to the in situ installation of the surface fans. A solution was identified in the oil and gas industry through collaboration and innovative thinking. This paper describes the sustainable approach to implement a reliable air flow monitoring system on-site.CITATION:Shearer, M J, 2017. Case study – an analysis of reliability and efficiency: ultrasonic versus annubar technologies, in Proceedings Australian Mine Vent Conference 2017, pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By C Simpson

The Pilbara region of Western Australia is well known for its abundant exports of hematite-goethite deposits, which have been mined and exported since the 1960s. Magnetite has also been mined in Australia throughout this period, although historically of much lower production volumes (WA Iron Ore profile, 2016). Magnetite offers a source supply of material >66 per cent iron grade product, which is used as premium feed (predominantly pellets) to blast furnaces or specialised steel mills.The Iron Bridge project area contains outcropping magnetite and hematite banded iron formation (BIF), which within the region was recognised as having potential to host economic mineralisation during the 1960s. Development within the project area, however, did not commence until Fortescue Metals Group acquired the tenements based on a 2004 agreement, formed a joint venture with interested groups and then initiated an assessment for magnetite (rather than hematite) mining potential. The combined deposits now have an identified large mineral resource inventory, with test work demonstrating they are able to produce a magnetite concentrate of greater than 66 per cent Fe over an extended mine life. This concentrate would be suitable for forming pellets or feed for direct reduced iron products.The deposits form a singular orebody, approximately 12 km in length by 1 km in width and extending to depths beyond 600 m. The four main deposits are geographically separate and have subtle mineralogical differences, thought driven by the degree of deformation and alteration within each area.Definition of the stratigraphy, structure and key mineralogy of the deposits has been carried out through several stages of exploration and project development. This has also included recent mining and processing of more than 1 Mt of feed material to an on-site processing facility. This demonstrated at a production scale that dry plus wet processing techniques can efficiently separate the magnetite from the gangue minerals to form a suitable (marketable) product.Geometallurgical classification of the host stratigraphy has been carried out from analysing the high volume of quantitative data available for this deposit. This has allowed definition of mappable units within the fresh BIF to be used as a driver in mine scheduling, delivering optimal feed to the processing plant.Construction of mine and processing facilities is expected to commence once all technical risks have been addressed, market conditions are deemed appropriate and approval is given by the joint venture partners.CITATION:Simpson, C, 2017. The Iron Bridge magnetite deposits, in Proceedings Iron Ore 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Brad Hewitt, Jeff Belke

"Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are:1. the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency;2. the decision to construct the thickener base from thickened solids;3. the lack of redundancy in the overflow, underflow and tailings pipe work; and4. the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system.In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system through mechanical modification as follows:•, CCD1 has a modified rake mechanism that now allows central vertical lift of 600 mm;•, CCD1 has forced dilution using the Outokumpu Turbodil® technology and replacing the E-Duc® technology of Eimco;The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1 per cent (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2 per cent improvement in the circuit underflow density.The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil®dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary solution neutralisation improvements."

Jan 1, 2005

By Niklas Willemsen

Introduction to SVCs ? SVC = Static var Compensator ? Dynamic step-less control of reactive power without switching of passive components: ? Voltage control/stabilization ? Harmonics- and flicker mitigation ? Dip mitigation ? Main components: ? TCR (Thyristor Controlled Reactor) ? Tuned harmonic filters ? Control- and cooling systems ? Typical applications: ? Mine hoists ? Large mining complexes ? EAF, SAF, rolling mills, wind/solar farms etc..

Aug 1, 2013

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

global mining boom and in-creased demand for iron ore has lead to a resurgence in the mining industry in Minnesota. At the combined 81st Annual Minnesota Section of SME Meeting and 69th Annual University of Minnesota Mining Symposium, April 15-16 in Duluth, MN, this resurgence was the hot topic as new mining projects were featured in the keynote session. The meeting attracted more than 400 mining industry professionals, including engineers, executives, mining managers and suppliers from around the world. This year?s theme was ?New Ventures in Mining.? The meeting included concurrent technical papers sessions, a keynote session that featured three distinguished speakers and a panel discussion that provided updates on new mining developments in the state. The Minnesota Section of SME technical papers were presented in concurrent sessions, one on mining and one on mineral processing. The mining session included papers on drilling, ore blending, slope stabilization, dust control and operations management. The mineral processing session included papers on plant-control technology, ball mills, pellet strength and fans. Also offered was an SME short course titled ?Simulation based pellet induration optimization.? The Minnesota Section of SME held its annual business meeting during the conference. The 69th Annual University of Minnesota Mining Symposium technical sessions were held on April 15 and also consisted of concurrent sessions on mining and mineral processing. Mining session topics included logistics management, real-time performance measurement, uses for taconite aggregate and environmental issues. The mineral processing session included papers on ore liberation characteristics, zeta potential studies, induration modeling, fuel optimization and conveyor belts. The combined conference included a tradeshow with more than 80 booth spaces featuring vendors offering products and services to Minnesota?s booming mining industry. More than 900 people, including conference registrants and special invited guests of the vendors, at-tended the tradeshow opening reception. This was the largest trade show in many years ? an indication of the vitality of the mining industry in Minnesota.

Jan 1, 2008

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By A. V. De Forest

INSPECTION and test methods of great diversity have been used from the most ancient times to select raw material, control its manufacture, and appraise its finished properties and value. The "miller thumb," expert in grading flour, the vintner's sense of taste, the goldsmith's micro-wear test on a touchstone, the enquiring sniff over the doubtful egg -these are all nondestructive inspection methods, accurate and depend- able, but not readily reduced to numbers in the c.g.s. system. A horse trader inspecting a possible purchase is interested in more than age, size, weight, color. heredity, speed, or drawbar pull which can be reduced to figures. Behavior, temperament, stamina, health-past, present and future---are just as important as the numerically determinate constants.

Jan 1, 1940

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By Frank R. Field, Randolph E. Kirchain, Elisa Alonso

"There are a number of environmental incentives for increasing recycling, including the reduction of waste, energy and resource use. Recycling can also be advantageous for manufacturing firms in both the short and long term. Secondary material can substitute for primary material, potentially dampening primary material price increases and reducing the pressure for greater primary extraction. This paper examines the potential for and dynamics of recycling for the case of platinum using a dynamic, behavioral simulation model of the primary and secondary markets. Since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities. Over time, recycling can cut primary consumption, reduce overall costs to firms, and possibly reduce the impact of price fluctuations upon firms.IntroductionThe benefits of recycling, from the perspective of the environment, are many, and the environmental benefits of increased recycling are considered a step towards increased sustainability [1, 2]. Life cycle assessments indicate that obtaining materials from secondary sources generally requires less energy and has fewer environmental impacts than extraction and refining of primary materials [3]. Analyses of materials flows show that, in addition to landfill volume reduction, recycling reduces primary material consumption, affecting long term materials scarcity [4, 5].The benefits of recycling are not limited to the environmental. Firms can benefit from the lower energy costs of recycling, especially that of metals whose primary extraction and refining are particularly energy-intensive (e.g., aluminum). The routine participation by firms in secondary materials markets (e.g., www.recycle.net) shows that this advantage has not gone unnoticed.Recycling can also benefit firms whose costs can be significantly affected by changes in material prices resulting from material shortages and material scarcity, with potentially permanent effects upon firms [6-8]. This paper focuses on the impact of recycling in the face of platinum scarcity for supply chain downstream firms."

Jan 1, 2008