Search Documents

By Jacob Carr, Bruce Whisner, Adam Smith, Jingcheng Li

Electromagnetic-based proximity detection systems (PDSs) are utilized on mining machinery to protect workers from being pinned or struck. These systems generate magnetic fields covering the space around a machine, and a miner-wearable component (MWC) detects the field. The PDS determines the distance of miners relative to the machine based on the detected magnetic flux density in the magnetic field. This information is used to establish warning and shutdown zones around the machine. Maintaining a stable magnetic field is essential for system accuracy. However, components used to generate magnetic fields can be influenced by temperature changes. Depending on ventilation conditions and seasonal alternation, a PDS can be subject to significant temperature fluctuation. To better understand and quantify this phenomenon, researchers from the National Institute for Occupational Safety and Health (NIOSH) developed an experimental apparatus to study the influence of temperature on magnetic field generator circuits used in PDSs. Results from the study show that the electric current through a generator can be influenced by both ambient and internal temperatures, modifying the magnetic field that is produced. These findings show that temperature can significantly influence the ability of PDSs, used in underground coal mines, to accurately determine a worker’s position in relation to mining machine.

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use, in a helicopter. Tests showed that EM signals from lightweight (3/4 lb) transmitters could be detected both on the surface and from a helicopter through as much as 4450 ft of relatively high conductivity (2 X 10- 2 mhos/m) overburden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 1, 1973

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

Tellurium (Te) is one of the least abundant elements in the crust and tends to form minerals associated with copper, lead, zinc and iron sulfide deposits. Today, most tellurium production comes from the anode slimes and other wastes generated in metal refining. Most of the current tellurium produced in the world is used as an alloying agent in iron and steel, as catalysts, and in the chemical industry. However, future demand and production could increase because tellurium is increasingly used in solar panels and some electronic devices. Tellurium minerals are found in Au-Ag districts in New Mexico, but were not considered important exploration targets in the past. In New Mexico, tellurium is found associated with porphyry copper deposits in southwestern New Mexico and with Au-Ag veins in the Eureka, Sylvanite, Organ, Lordsburg, Steeple Rock, Wilcox, Mogollon, Chloride, Cuchillo, Hillsboro, Zuni Mountains, White Oaks, and Nogal-Bonito districts. The only tellurium production from New Mexico has been from the Lone Pine deposit (Wilcox district), where approximately 5 tons of tellurium ore was produced. Gold-tellurides are found with gold, silver, pyrite, and fluorite in fracture-filling veins in rhyolite at Lone Pine, with reported assays as much as 5,000 ppm Te. Other districts in New Mexico have potential for tellurium, but require field evaluation.

Feb 27, 2013