Search Documents

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

The works of Metal Manufactures Ltd are situated at Port Kemblam NSW, within a few hundred yards of a deep-water harbour. At present they occupy about 26 acres, and ample provision has been made for future extensions. Rail connection exists between various parts of the Works and the main South Coast Railway, the harbour jetties and the adjacent copper refinery of The Electrolytic Refining and Smelting Co Ltd. A plan of the works is shown in Fig 1.The company was incorporated in March 1916, and commenced production of copper wire in June 1918. Early in 1920, tube manufacture was undertaken, followed by telephone cable mnufacture in 1923. Today the Works consist of five principal sections: Founrdy, Tube Factory, Wire Factory, Cable Factory and Case and Drum Factory. Whilst the last four are engaged in producing the finished materials for despatch from the Works, the first-mentioned is engaged in producing copper, brass, and other non-ferrous billets for use in the Tube and Wire factories. In addition, there are Engineering and Metallurgical Departments supporting the manufacturing sections, and in these, as well as in all other sections of the Works, extensions have been carried out from time to time to provide for increased output and new types of products.

Jan 1, 1938

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973

One of the problems associated with the maintenance of roadways in underground coal mines is that of dealing with roadway closure. Sidewall weakening technique is based on the transference of the high stress zone further away from the vicinity of roadway. This transferral is carried out by weakening parts of sidewalls of roadway by cut- ting slot, drilling a series of parallel holes or blasting during development stage. In the paper, the effect of sidewall weakening on the stability of roadway is studied by finite element analysis and field experiment. The finite element analysis shows that sidewall weakening can control the development of yield zone around a roadway, improving the stability of roadway. It is also shown that if in- situ horizontal stress is lower or higher than the in-situ vertical stress, it is difficult to obtain roadway stability by sidewall weakening. The field experiment shows that roadway closure can be controlled by sidewall weakening with blasting.

Jan 1, 1990

By M. S. Delibalta, S. Kahraman, R. Comakli

The block cutting machine is one of the most important noise sources in the stone processing factories. In this study, the assessability of the noise from the block cutting machines in the stone processing factories using the P-wave velocity was investigated. The noise levels of some block cutting machines were firstly measured during the cutting of the three different rocks. Then, core samples of the same rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. A conversion factor was obtained by dividing the site noise levels by the laboratory noise levels. Then, thirty seven different rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. The P-wave velocity of rock samples were also measured in the laboratory. A strong relation between the laboratory noise levels and the P-wave velocity was found. The noise level from the block cutting machines can be assessed using the derived relation and the conversion factor.

Jan 1, 2011

By M. C. Chapman, P. L. Swanson, A. T. Iannacchione

The National Institute for Occupational Safety and Health (NIOSH) evaluated microseismic activity from three field sites to compare and contrast the characteristics of microseismic emissions from very different geologic, stress, and mining environments. Recently, NIOSH has embarked on a research program to evaluate the use of microseismic monitoring information to identify roof fall failure processes and to assess its potential to warn of unstable roof conditions. Large roof instabilities, such as roof falls and certain roof caving events, have proven difficult to anticipate representing an increased risk to miners working in these inherently hazardous areas. When local failure processes are better understood, appropriate control measures can be engineered to mitigate these hazards. This study used microseismic emissions to help identify three local rock failure processes. It was also shown that analysis of microseismic emissions can aid in assessing the degree of instability associated with these local rock failure processes.

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By J. I. Schoenherr, G. Schubert, F. Demczenko

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts of fine bulky materials (<3 mm). These wastes are mostly given to specialized landfill sites. Starting out from classical and traditional beneficiation processes a new research project was initiated to work on certain new ways to efficiently separate plastic material mixes. First basic results show that the use of new and improved thermal beneficiation methods is a great implementation in the field of plastics separation. The results can be further increased by a suitable combination with other methods as well. This leads to high-quality and almost pure separated plastics and rubber products, easy to sell on recycling product markets.

Jan 1, 2002

A method for the detection and analysis of tin in cassiterite ores is discussed. An empirical relationship was established between the tin content of an ore sample and the percentage absorption that this sample produced in a Mossbauer experiment. The time taken to complete an assay with this method is much less than with any of the methods currently in use. The equipment can be adapted readily for use in the field.

Jan 1, 1969

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou&apos;gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By Margaret R. Egan

A series of experiments were undertaken by the Bureau of Mines to determine the emission products of several types of conveyor belting and other combustible materials found in mines. These experiments were conducted under intermediate-scale, simulated mine conditions to determine smoke characteristics and gas concentrations. From these determinations, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. Three types of belts were investigated: chloroprene, also known as neoprene (NP); polyvinyl chloride (PVC); and styrene-butadiene rubber (SBR). The belts were designated as ignitable or self-extinguishing depending on the length of the burning time and the subsequent combustion products. Under these experimental conditions, the SBR belts were the easiest to ignite. The PVC and NP belts tended to self- extinguish within a few minutes after ignition, but were still capable of maintaining a brief flaming period. These conveyor belt combustion results are compared with previous analyses of wood, transformer fluid, and coal fires. Together they form a data base by which findings from future experiments with other mine combustibles can be compared.

Jan 1, 1988

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

Dump site injuries occur in all major mineral industries. Working in elevated areas near an edge is a common hazard for operators of off-highway mobile mining equipment. In this Information Circular (IC), serious injuries involving haulage trucks working at dump sites are examined for the period 1988 to 1997. Data were acquired from injury reports gathered by the Mine Safety and Health Administration (MSHA). The IC is organized into three sections. The first presents an overview of the frequency and severity of injuries. The second analyzes injury characteristics using MSHA-defined data fields and author-defined injury classifications. Key findings are discussed in the third section. In summary, 370 serious injuries were identified that involved trucks at dump sites, of which 26 were fatalities. Although haulage truck activities at dump sites resulted in a small proportion of the total number of injuries at surface mines, these injuries were much more likely to result in death or significant amounts of lost time than most other surface mine injuries. These findings support the belief that haulage truck activities at dump sites are worthy of continued study by those interested in improving the health and safety of workers at surface mines.

Jan 3, 2001

By Cooper R. J

The essential features of the zinc concentrate roasting installation at the Risdon Works by the Electrolytic Zinc Company of Australasia Ltd. are given.The problem of maintenance of ignition in down-draught zinc concentrate flash roasters is discussed, and a solution offered.A successful and economical method of using by-product oxygen for raising the roasting efficiency of hearth roasters is described. Three methods of utilizing oxygen for the same purpose in flash roasting are detailed, and their relative merit, considered.INTRODUCTIONThe zinc sulphide concentrate used at the Risdon Works is roasted autogenously for removal of sulphur in two hearth roasters, and four flash roasters. The hearth roasters are of modified Skinner type with eleven hearths. They were designed, and are used, for roasting mixtures of relatively low sulphide content. Their design and operation have been described elsewhere (Forster, 1949).The flash roasters are down-draughted furnaces with cross-section and rabbling equipment based on the hearth roaster design, and the process is similar to that developed by the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. (Stimmel, Hannay, and McBean, 1936).These furnaces are 20 ft. in diameter. They have three drying hearths through which hot gas is drawn from the combustion chamber by the burner fan. The combustion chamber is 2&apos;1 ft. high above the collecting hearth (27 ft. in No. 4 unit), and the discharge hearth below it is 6 ft. high, so that a large gas offtake is possible. Four rabble arms for each hearth are carried on a central column. Dried, ground concentrate, and the air for roasting it, are fed to a burner...

Jan 1, 1958

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984

By H Ulrich Leiste, Leslie Talor

This paper describes a series of small scale tests conducted to investigate the loading applied to a flat plate by the detonation of a cylindrical charge very close (between two and three charge radii from the center of the charge) to the structure. The testing used very small quantities of explosive (PETN): Two different series of tests were conducted. In the first test series, impulse loading on the target plate was investigated using three different sizes of charge. In the second series, pressure time profiles were determined. The charge size was 6 g or less. Impulse was found using high speed video of the target plate to determine its displacement as a function of time, from which initial plate velocity was obtained. Kolsky Bars, placed at the same distance from the charge as the target plate, were used to determine the free-field pressure time profile of the output of the charge at this distance. Two different types of target plates were used in the impulse study. One was just a plate while the other was a plate constrained with a steel frame.

Jan 1, 2009

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986

By Weber P, Sneyd S

The total world steel production in 1998 amounted to approximately 780 000 000 t. The share of electric steelmaking was in the range of 35 per cent and is expected to increase further to over 40 per cent of the world&apos;s production within the next ten years. As electric steelmaking is primarily based on the use of scrap and as it is progressing more and more into higher steel grades the need for low-residual metallics will become increasingly important. Consequently, the demand for scrap substitute material will increase, reflected in the world wide spate of interest for DRI (Direct Reduced Iron) and HBI (Hot Briquetted Iron). The increased significance of DRI/HBI as a substitute for steel scrap has obviously emanated also from its comparatively lower and more predictable costs per ton and definable chemistry. In 1998 already 37 million tons of DRI/HBI were globally produced.

Jan 1, 1999