Search Documents

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

The area around Big Bell was actively explored and sporadically mined for gold from 1904 onwards. The lease was named Big Bell in 1913. The property became established as a major mining centre with the development of the Big Bell underground mine in 1936. Mining operations commenced in late 1937 and ceased in January 1955, after milling 5.56 million tonnes of ore and producing nearly 21 tonnes of gold. In 1969 Australian Consolidated Minerals Ltd (A.C.M.) acquired the deposit then explored it alone and in joint venture until the current joint venture agreement with a subsidiary of Placer Pacific Limited (PPL) was negotiated in 1984. Following exploration and evaluation of near surface mineralisation, and a reassessment of the remnant pillars underground, the concept of a large open pit in conjunction with an underground mine evolved. The feasibility study was completed in October 1987, and the decision to go ahead was formally announced on 2nd December 1987. Placer Dome Technical Services Ltd were contracted to be the Project Managers, commencing construction on site early in January 1988 and handing the plant over to the operators 13 months later. The capital cost of the project at handover was estimated to be $133 million. The operating team commenced pre-production stripping of the open pit on 1st May 1988. By 31st January 1989 almost 16.0 million tonnes had been stripped and 350,000 tonnes of ore stockpiled.

Jan 1, 1989

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By E N. Sajin

The final arsenic bearing waste products at the majority of metallurgical and chemical enterprises are cakes in which arsenic is present in the form of calcium arsenate. Burial of cakes demands construction of special burial sites and does not guarantee reliable protection from arsenic penetration into the ground and surface waters. Under laboratory conditions we developed technology for processing calcium arsenate cakes with obtaining low toxic products suitable for long-term storage, meeting environmental requirements. The investigations have shown that thermal processing of briquetted mixtures of cakes containing 15 - 20 per cent weight of pyrite under the temperature of 873 - 923¦K during 45 - 60 minutes gives briquettes sufficiently hard for transportation and long-term storage. Arsenic, under high sulphidisation temperature is bonded into low solubility non-volatile iron sulphide bearing compounds having chemical properties similar to the natural arsenic compounds. Solubility of the obtained products in neutral, acid and alkaline media was investigated during long period of time (three to 12 months). It was determined that arsenic content in the solutions did not exceed the norms for cultural and welfare basins and fish-ponds.

Jan 1, 2002

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By Y Chen, G Xu, B Albijanic

High concentrations of airborne coal particles is the main reason leading to health and safety hazards in underground coalmines. Water spray is one of the effective methods to suppress coal particles in mine sites, but the use of plain water is not effective enough to capture coal particles. By adding surfactants, coal wettability can be improved which will increase the coal dust suppression efficiency. In this study, a modified sink test was employed to evaluate coal wettability in the presence of two anionic surfactants: sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS). Sink rates were calculated by measuring sink weight over test time. Different surfactant concentrations (0.01 per cent, 0.05 per cent, 0.1 per cent, 0.2 per cent and 0.4 per cent) and two types of water (tap water and deionised water) were selected to investigate coal wettability over three size ranges (0–38, 53–75 and 75–90 µm). The results show that both SDS and SDBS surfactants can lower the water surface tension and improve coal wetting performance. Sink rates increased as the surfactant concentration increased, and surfactant solutions prepared by tap water performed better than deionised water in enhancing coal wettability. Also, coal wettability varied for different coal particle sizes; the smaller coal particles were, the worse the wettability they possessed.CITATION:Chen, Y, Xu, G, Wang, R and Albijanic, B, 2017. Study on coal wettability for dust suppression in the presence of surfactants by sink test, in Proceedings Australian Mine Vent Conference 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The beach sand industry is the only Australian mineral industry which, so far, has used electrostatic separation on a full commercial scale. The main application of the process is for the separation of rutile from zircon. Laboratory work has demonstrated that electrostatic methods are effective for ilmenite-monazite and cassiterite-zircon separations, thus facilitating the production of high grade monazite and cassiterite products from top-strip table concentrates, but the commercial application of these processeshas been rather limited so far. Overseas, electrostatic methods are becoming more widely used for the treatment of granular material which is not amenable to flotation. The use of electrostatic separation for the treatment of ores other than beach sands has been investigated in this laboratory 1, 2, 3, and two pilot separators were built during i953 to carry out field tests. Of these, the first was an inclined feed plate separator for the removal of silica from granular lime-sand in Western Australia, the second a conductance roll separator for the removal of diamonds from alluvial gravel in New South Wales. In both cases the whole of the ore passed through the separator, not a gravity concentrate only as in beach sand practice. The two types of separator mentioned are shown diagramatically in Figs. 1 and 2.

Jan 1, 1954

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a 'possibility, and that it was unlikely that a small bore...

Jan 1, 1950

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974