Search Documents

By Bibhu Mohanty, Sheng Huang

Accurate measure of fragment size distribution is a key objective in all blasting and crushing operations. Several generic distribution functions have been devised to describe the degree of fragmentation for the representative range of fragments from selected measurements. The application of four distribution functions, i.e. Rosin-Rammler, Swebrec, Grady and Gilvarry, in describing fragment size distribution of impact-induced fragmentation of a limestone rock has been investigated. A modified Hopkinson Pressure Bar experimental set-up is used to control both impact velocity and energy input into the target rock. The feed size in the sample holder is varied from 6.35mm to 15.88mm in three ranges and the impact velocity up to 14m/s. The size distribution in the product is determined by sieve analysis for a range of impacts. The experimental results are fitted to the four distribution functions to examine their relative accuracy and reliability.

Jan 1, 2016

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By G. Price

The Building Research Establishment installed a base load cell in a driven cast-in-place pile prior to it being tested under vertical load. The monitored base loads were found to be significantly less than could have been predicted by current design methods. The less than expected capacity was attributed to the drilling out procedure. An electro-level system installed in a second similarly formed pile, provided detailed information on the performance of the pile under lateral load. The information obtained was used to check several current design methods for laterally loaded piles. The findings show the potential dangers of attempting to improve design parameters from only limited performance data.

Jan 1, 2010

Develop hydrometallurgical or pyrometallurgical recycling methods to recover valuable rare-earth compounds from various forms of NdFeB magnet scrap. Background The U.S. Bureau of Mines (USBM) has developed technology to treat and recycle a variety of wastes containing valuable and strategic metals. As part of this effort, the USBM developed a process to separate neodymium and other valuable rare earths from iron in NdFeB magnet scrap (fig. 1). Since this scrap typically contains nearly 30 weight percent neodymium and since the demand for neodymium is constantly increasing, cost-effective methods for scrap treatment could have a significant impact on industrial expenditure and materials supply in the expanding area of magnet manufacture. Approach A hydromctallurgical, H2SO4 dissolution-precipitation process provided the most effective treatment for separating rare earths from bulk NdFcB magnet scrap (fig. 2). Precipitation of neodymium-alkali sulfate double salt proved advantageous over direct precipitation of fluoride or oxalate products. This double salt is easily converted to a variety of useful rare-earth compounds, which eliminates many of the materials-handling and economic problems inherent with direct precipitation. Following rare-earth precipitation, dissolved iron was removed from the acid leach solution by precipitation as a jarosite.

Jan 1, 1993

By Neal Lee, Braden T. Lusk, Jhon Silva-Castro, Patrick J. Jenks

"Timing and charge sequence are very important for optimized blast design. Traditional nonelectricinitiation systems have moved the industry toward a system of delays consisting of hole-to-hole androw-to-row timing sequences that mimic the application of nonelectric surface delays or dual delayinitiator systems that have been prevalent in the blasting industry for many years. The increasedutilization of electronic detonators allows for the use of Regular Rhythmic Timing (RRT) utilizing onlyone delay between charges and a selected charge firing sequence. The hole to hole and row to row (HHRR) timing method has been utilized for blasting optimization and allows for simplistic changes to the tie in phase of the blasting sequence. When using this traditional timing methodology, for some specific cases related to the number holes and rows, crowding occurs in the delay between charges with subsequent increase in the peak particle velocity (PPV) produced by the blast. This is in contrast to RRT where the timing between the delays remains constant."

Jan 1, 2016

This paper examines the integration of risk management into the design philosophy of a project to produce a æzero baseÆ design, which targets a minimum capital cost without adversely impacting upon the operating costs of the resulting plant. The concept of zero base design is similar to zero base budgeting and the desired outcome is to improve the economy of the design. Design requirements are questioned in an attempt to distinguish preference, prejudice and myth from necessity. Where doubt remains a risk management approach is adopted. The key to risk management is not risk elimination, but risk mitigation. Risks can be managed by designing them out, but often this involves considerable capital cost penalties and it is more attractive to accept the risk and design an operating strategy to deal with it. The paper discusses this with some examples of real world risk mitigation strategies that resulted in substantial capital cost savings. The paper concludes that as much as a quarter of project capital costs can be eliminated by a combination of zero base design and carefully crafted risk mitigation strategies.

Jan 1, 2004

By . Jaime G Tapia Aguirre

La Unidad Minera Rosaura del Grupo Glencore fue considerada la mina subterránea más segura del país durante los años 2005, 2006 y 2007. Sin embargo, cuando el Grupo Glencore adquirió la concesión de Rosaura, el panorama minero era de una mina marginal, de bajas leyes. Por esta razón, el único metodo a ejecutar para hacer de Rosaura una mina rentable era el de utilizar un método masivo. Em ese semtido, el presente texto señala la operación de mina cone el análisis y conocimiento de causa raíz en la prevención de caída de roca.

Sep 12, 2011

By C. G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX/EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to copper concentrates and ores will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of chalcopyrite concentrate treatment with this unique industrially proven process will be delineated.

Jan 1, 2001

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By G Mark, K L. Blake, G de Jong, J F. Rotherham, N D. Adshead

Magnetite deposits with distinctive ¦ actinolite ¦ apatite-bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (egKiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (eg Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidised fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelised influx of a specialised high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By Luis Magallanes-Hernández

"Industrias Peñoles, S.A. de C.V. (Peñoles) in Mexico, is a major silver producer. The Peñoles Mining Division has eight Mining Operations and in seven of them, flotation is used to concentrate the metal and mineral values. Common metals and minerals values are: metallic gold and silver, gold-silver alloys, silver sulphide minerals (acantite, pyrargirite, argentite, proustite); lead sulphide mineral, galena; zinc sulphide mineral, sphalerite; and copper sulphide minerals (chalcopyrite and bornite).In the last years, a special emphasis has been given to using modal analysis to identify ore mineralogical limitations, in order to direct efforts into key areas where opportunities exist to improve the metallurgical results.This work aims to share Peñoles mineralogical and metallurgical results, through presenting, discussing and drawing conclusions on these results; as well as pointing out areas where more work is needed to improve the Concentrator´ performance.PEÑOLES BACKGROUNDPeñoles´s mission is to add value to non-renewable natural resources on a sustainable manner. It was established in 1887, and it is a mining group with integrated operations in smelting and refining non-ferrous metals, and producing chemicals. Peñoles is the world’s top producer of refined silver, metallic bismuth, and sodium sulphate, the leading Latin American producer of refined gold, lead, and zinc.Peñoles Mining Division is integrated into eight mining business, located on five different states in Mexico. Metal productions for the Mining Division during 2003 were: 343 thousand gold ounces, 48.4 million silver ounces, 81.3 thousand tons of lead, 235.1 thousand tons of zinc, and 10.6 thousand tons of copper."

Jan 1, 2005

By Y Zhang, X Yi, J Deng, J Zhao, J Song

To obtain the combustion process of a coal fire, a high-temperature programmed system is used to simulate the spontaneous combustion process of fresh and weathered coals. Both fresh coal and weathered coals from Liulingou, Inner Mongolia, China, were used to examine the gas releases from constant temperature to 650°C. Moreover, gas release rate was used to calculate the characteristic temperatures. The results showed the coal samples lasted to oxidise under high temperatures, and released plenty of heat to assist self-heating. The humic acid contained inside the weathered coal went through thermal decomposition as temperature rising and generated gases. This resulted in increasing concentrations of CO, CO2, CH4, C2H4, and C2H6. Changes of CH4, C2H4, and C2H6 gases were also similar. For weathered coal, concentrations of three gases were kept in balance under low temperatures, increased rapidly with the temperature rising. After the ignition temperature, the concentration of hydrocarbon was reduced. In addition, particle size affected coal spontaneous combustion. Coal samples with less than 0.9 mm in size produced much more CO than others. This study has examined coal spontaneous combustion caused by coal weathering during mining and its impacts on self-heating and pyrolysis in the process.CITATION:Deng, J, Song, J, Zhao, J, Zhang, Y, Yi, X and Zhang, Y, 2017. Gaseous products of weathered coal during the process of spontaneous combustion, in Proceedings Australian Mine Vent Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By I Halikia, T Lilis

Lead smelter slags, produced during the last century in quantities ofmillions of tonnes at Lavrion, Greece, have recently been used in theconstruction of Lavrion harbour. In order to evaluate the geochemicalstability of slags and assess their environmental impact on the aquatic environment, a detailed study on lead leachability under conditions that simulate subsea environments was carried out. Leaching experiments using magnesium chloride solutions under mild temperature conditions were conducted and the effect of main parameters on lead solubility was examined. Furthermore, kinetic analysis on the experimental results was performed. Based on the results, lead dissolution increases by increasing the reaction time, magnesium chloride concentration in the bulk solution and temperature, whereas it decreases by increasing the slags particle size. The reaction order was found to be approximately 0.5 at the initial extraction stages and the activation energy value from the Arrhenius plot was estimated to 29.8 KJ/mole. Diagnostic equations applied to all the experimental data reveal that lead dissolution is mainly controlled by diffusion through the ferrosilicate matrix of the slag particles, which is in accordance with the low activation energy value. The JanderÆs diffusion equation [1-(1-a)1/3]2=kt was proposed as the equation representing the reaction of lead dissolution from slags using magnesium chloride solutions.

Jan 1, 1999

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009