Search Documents

By C. Özgen Karacan

Methane emissions from the active face areas and from the fractured formations overlying the mined coalbed can affect safety and productivity in longwall mines. Since ventilation alone may not be sufficient to control the methane levels on a longwall operation, gob vent boreholes (GVB), horizontal and vertical drainage boreholes, and their combinations are drilled and used as supplementary methane control measures in many mines. However, in most cases, the types of degasification wellbores chosen are decided based on previous experiences without analyzing the different factors that may affect this decision. This study describes the development of an expert classification system used as a decision tool. It was built using a multilayer perceptron (MLP) type artificial neural network (ANN) structure. The ANN was trained using different geographical locations, longwall operation parameters, and coalbed characteristics as input and was tested to classify the output into four different selections, which are actual degasification designs that US longwall mines utilize. The ANN network selected no degasification, GVB, horizontal and GVB, and horizontal, vertical and GVB options with high accuracy. The results suggest that the model can be used as a decision tool for degasification system selection using site- and mine-specific conditions. Such a model can also be used as a screening tool to decide which degasification design should be investigated in detail with more complex numerical techniques.

Jan 1, 2009

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By Xu H.

In recent years, the mineral applications dealing with more complex data in distributed environment have grown rapidly. Many mineral and mining organizations have to organize internally and globally distributed manufacturing and experiment sites, which share the roles of databases and other multi-services like software programs. Thus, there are commercial and technical pressures pushing the mineral software vendors to move their current service toward Web service. XML has gained wide acceptance for representing, storing and transferring structured data and documents of many kinds, especially in scientific communities. However, so far there is no such a Markup Language in mineral industry. A XML-based uniform encoding, which is called MineML(Mineral Markup Language), is proposed and developed in this project. The framework of the MineML specification is created. MineML will play the role as shared protocols within mineral domain for archiving, transferring the multi-nature data between the software packages on the desktop over the Internet and sharing the services between users at different sites. Inspired by MLA’s (Mineral Liberation Analyser, JKMRC, University of Queensland, Australia) Mineralogical Data Presentation Program, a proof-of-concept prototype of Web Service is developed here to validate and demonstrate the MineML specification. Certain strategies, specific technologies and tools are adopted to create such an environment. To accomplish that, a set of experimental MineML documents including correlated XML, XSD (schemas) and XSL(stylesheets) documents have been elaborated for archiving, presenting and transferring the mineralogical data information, with the persistence on flexibility and extensibility for generic mineral and mining data handling.

Jan 1, 2003

This report provides concepts for two automated longwall mining systems; one for operation in a 42 to 57-inch thick section of the Lower Kittanning coal seam, the other in a 57 to 72-inch thick section of the Pittsburgh seam. The Lower Kittanning concept uses a single-drum bidirectional shearer and 500-ton capacity 4-leg chocks and the Pittsburgh concept uses a double-drum shearer with 500-ton shields. Each concept is designed to produce in excess of 2,500 tons of clean coal per shift with a 6-man face crew. The automated longwalls consist of off-the-shelf control system hardware attached to standard longwall equipment. Control hardware includes a control and display console; prime and backup mini-computers; multiplex data transmission, power, and control lines; several remote terminals which serve as interface junctions; and various sensors and actuators located on the longwall equipment. The system can be operated either fully automatically, remotely or manually.

Jan 1, 1976

By Ramón Alanís, Filiberto Orrante, Andrea Festa, Baldomero Gutiérrez, Fernando Cornejo

"SGS implemented two rules-based fuzzy logic expert applications on two grinding circuits operated by Peñoles Group in Mexico. Both expert systems are based on control strategies that push against process constraints to improve throughput. Based on proven methodologies, the projects also required some new approaches that led to permanent changes to the mill control strategy.This paper provides descriptions of the implementation, operation and performance of both expert systems. It also reviews how improved production rates were achieved through the use of a common set of expert technology tools. An overview of the resulting control strategies implemented on the two circuits is presented. The paper also discusses the identification of the process constraints within each circuit and how these constraints are used within the expert systems.INTRODUCTIONMexico-based mining company Peñoles Group and the Advanced Systems group at SGS, formally known as MinnovEX Technologies Inc., collaborated on the implementation of two expert systems in two grinding plants, both located in Northern Mexico.The primary objective of the expert systems was to increase throughput whilst still maintaining the cyclone overflow product size within an acceptable range. The secondary objective was to achieve a high level of utilisation of the expert technology.In order to achieve these objectives, SGS proposed a proven methodology which leveraged the existing operating and technical expertise at site through the client’s involvement in the design and implementation stages. The in-house operating and technical expertise of SGS was also brought to the project and implemented with the client’s approval at all stages. At both sites the final acceptance was defined upon meeting both process and utilization parameters.The development and deployment of rules-based fuzzy logic applications has matured as a technology and consequently, clear definition of process states and their place in the logic structure to control a given circuit are now transferable. The key to the robustness of the control logic depends on selection and tuning rules for maintaining stability and optimizing a given circuit. Application integrators need to have a standardized approach for timely integration and deployment; a critical component to avoid the common critiques that expert applications are idiosyncratic and difficult to maintain."

Jan 1, 2009

By R. C. Adams

This report describes the feasibility of mining the oil shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By Donald Christofferson

This report documents the program conducted to demonstrate the application of a flywheel-powered propulsion system to underground mining shuttle cars. Such application can replace the present electrical trailing cable common to most shuttle cars and thereby eliminate those safety hazards, maintenance problems, and haulage route limitations inherent in the trailing cable. Described are the activities undertaken to specify and design a flywheel of optimum size, shape, and material; to identify the best concepts of input and output systems; and to achieve installation of the power package into a shuttle car. The resultant Flywheel-Powered Shuttle Car is an FMC Model 6L shuttle car, 6-ton capacity, 20-ton gross vehicle weight, powered by a flywheel system with 4.5-kilowatt-hour usable energy. The completed vehicle was delivered to the Bureau of Mines in Bruceton, Pennsylvania, for testing and evaluation.

Jan 1, 1986

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By Michael K. Watkeys, Charlesworth. E. GUY, Jacobus E. Potgieter, Anhaeusser. Carl R., Roger L. Gibson, Alexander F. M. Kisters

Abstract - Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-crustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress (?1 - ?3) during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diaper -like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By H. O. Hofman

WHEN dry chlorine gas is made to act in the cold upon finely¬divided gold,' it converts the latter with evolution of heat into auro-auric chloride, Au2CI4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and aerie chloride, Au2C14 = AuCI + AuCI3; treatment with water converts it into auric chloride and gold, 3 Au2CI4 = 4 AuC13 + Au,. Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCI = AuCI3 + Au,. These decompositions of auro-auric chloride and of aurous chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose,' fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also states that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed checks, and finally stops, further action, if the percentage of silver be increased beyond a certain undetermined amount. Bromine' acts upon finely-divided gold in a manner similar to chlorine; the auro-auric bromide, Au2Br4, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach-

Mar 1, 1905

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By Milton H. Fies

To present some idea as to how the Bureau of Mines may most effectively serve mining, it is necessary that we make some resume of its pact accomplishments in order to determine what, if any, changes will be of greatest service to the industry and to the nation. There are a great many times in life when one begins to wonder whether or not Emerson, in his famous epigram about "mousetraps" and "beaten paths" and "final recognition of intrinsic worth", took into account the item of time. The intrinsic value of any movement, of any work, of any accomplishment will ultimately be recognized, of that there is no doubt, but may a man in history has gone to his end in martyrdom because the world was slow in the acknowledgement of the true excellence of his worth, and this is likewise true of institutions.

Jan 1, 1934

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels - from mining and processing to the manufacturing of finished products. In 2010, the estimated real GDP of the United States increased by 2.8 percent compared with 2009 and the estimated nominal GDP was about $14.6 trillion (Table 1).Trends in various sectors of the domestic economy are often rejected in mineral production and consumption rates. For instance, continued declines in the construction industry during 2010 were rejected in further reductions in the production and consumption of cement, construction sand and gravel, crushed stone and gypsum, which are used almost exclusively in construction. Performances in other sectors were mixed and less easily characterized. Recovery from the economic decline of 2008-2009 became apparent in 2010, as prices for many mineral commodities continued to rise with increasing demand for those materials or the products in which they are found.

Jan 1, 2011

By J. Spotts McDowell

Ackowledgments........................... 5 Introduction............................. 5 The Silica Minerals. Stability Relations......................... 6 Optical Properties........................ 9 Density.............................. 10 Melting Points....;..................... 10 Thermal Expansion..................,..... 10 Solubilities............................ 12 Identification of Cristobalite and Tridymite.............. 12. The Silica Refractories. Raw Materia1........................... 13 American Deposits....................... 13 Properties Determining Usability................ 15 Expansion on Heating..................... 16 Texture........................... 17 Silica Brick............................ 17 Manufacture........................... 18 Properties of Silica Brick .................... 19 Analysis ......................... 19 Density......................... 19 Porosity......................... 20 Strength....................... 21 Melting Point....................... 22 Specific Heat....................... 22 Thermal Conductivity................... 23 Expansion........................ 24 Effect of Rapid Temperature Change.........:... 26 Constitution......................... 26

Jan 1, 1918

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008