Search Documents

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors' claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947

By B. J. Moore

This publication contains analyses and related source data for 310 natural gas samples from wells and pipelines in 16 States. All of the samples were obtained and analyzed during calendar year 1978 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis appara¬tus, which are described in Bureau of Mines Bulletins 4862/ and 576.3/ The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Twenty previous publications have presented the results of 11,573 gas analyses made prior to 197R. The first three, Bulletins 486,4/ 576,5/ and 617,6/ contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 17

Jan 1, 1979

By M. A. Leosson, S. H. Bottrell, R. J. Newton

Sylvite at Boulby is mined 1 140 m beneath the sea and the mine suffers from the influx of water. This is of two kinds: persistent flows originating in the Sherwood Sandstone aquifer and entering the evaporite sequence through fractures in the intervening mudstone, and impersistent flows which are transient in nature and of uncertain origin. Water from the overlying sandstone has become enriched with NaCl and large amounts of KCl and some Mg and Br have been added by interaction with the evaporites. Waters from the transient flows are isotopically distinct from those in the Sherwood Sandstone, being enriched in H and O. They are also saturated with respect to halite and sylvite, but have higher K/Na than the persistent flows and are much more enriched in Mg and Br

Jun 18, 1905

By L. L. Wyman

THE exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics, 1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors" wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickel-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-1 per degree Centi-grade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working can cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carbon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys.

Jan 1, 1939

By M. M. Valenta

A number of challenges face platinum concentrator plant operators. These challenges include the increase in operating costs, the increase in smelter cost for the processing of concentrate, the shortage and cost of power, and the tightening of specifications on concentrate quality by the toll-smelting operations. Over the years the focus has moved from extracting the platinum group metals (PGM) from the Merensky Reef to the UG2 reef. This has a number of advantages, including the higher ?basket price? for UG2 concentrate, reduced mining cost per unit volume as a result of the higher density of UG2, and the reduction in overall concentrate tonnage to be smelted. In many cases the Merensky ore has been fully exploited and it makes sense for the focus to shift to the UG2 ore that can be accessed through the Merensky shaft infrastructure. The presence of relatively high levels of chromite in UG2 concentrate is, however, a major disadvantage due to the problems associated with smelting such a concentrate in conventional submerged arc furnaces. In addition to increasing the specification on the minimum PGM grade of concentrates, smelters have had to impose strict specifications on the levels of chromite in the concentrate. The threat of high penalties has forced concentrators to change their modus operandi, often resulting in a significant loss in recovery. The final concentrate grades and PGM recoveries are shown to vary significantly throughout the industry. The reasons for this include varying ore mineralogy and different operating philosophies. This would therefore imply that the opportunity exists to optimize the operations by considering fundamental aspects such as the PGM mineralogy and the application of appropriate technologies. By returning to the fundamentals of flotation and applying the findings of detailed process reviews, it has been possible to increase the concentrate PGM grade, reduce the concentrate chromite grade, and in some cases increase the recovery of PGM to concentrate. This paper presents case studies where this approach has been used to successfully optimize concentrator performance, resulting in lower operating cost and higher PGM production. Keywords Process optimization, platinum concentrator, milling, flotation, grade, recovery

Jan 1, 2011

By Chris Breeds, Larry Leone, Jerry Wallace

Project Owners typically require General and Detailed Blast Plans when blasting close to important structures and specify the maximum allowable peak particle velocity for each potentially affected structure. Low, residential level PPV limits may be specified which significantly restricts the potential for blasting to be effectively used. Contractor’s responding to these contract conditions typically cite historic case studies which may, or may not, apply to the specific situation and/or types of structures for which limits have been set. A long submittal cycle typically follows.

Jan 1, 2010

Mineral Processing Engineering Education in China - Bringing up the Engineering Diathesis and Design Competence of the College Students

Sep 13, 2010

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By Lane White

In mid-April 1992, MINING ENGINEERING mailed a survey questionnaire relating to mining shovels and hydraulic excavators to 125 SME members working at surface mines or at the headquarters of companies that operate surface mines. The mailing was directed to individuals whose titles indicate that they have management or mine planning responsibilities for surface mining operations. A total of 56 usable surveys returned by June 17 are the basis of this report. Precious metals mines Eighteen precious metals mines or mining companies returned completed surveys in time to be included in this report. Of these, 14 use hydraulic shovels only for both ore and waste, I uses both hydraulic and rope shovels, and 2 use Caterpillar 988 front-end loaders for both ore and waste. (Of the latter 2, neither expects to be in the market for a shovel in the next three years. I of these 2 placed Harnischfeger P&H number one and O&K number two in response to the question, "Based on your current knowledge of their machines, which manufacturer would you likely chose to supply new shovels or excavators to a mine or mines operating under your responsibility, if you were in the market?") Another uses front-end loaders, make not designated. The latter does not expect to be in the market for mining shovels or excavators within the next three years. Of the final total of 14 precious metals mines using only hydraulic excavators to load ore and waste, 8 use Hitachi excavators only, 1 uses Demag excavators only, 1 uses Liebherr excavators only, 1 uses O&K excavators only, 1 uses Harnischfeger P&H and O&K excavators, 1 uses Harnischfeger P&H and Hitachi excavators, and 1 uses Hitachi and Demag excavators. Of the 14 precious metals mines using only hydraulic excavators, 7 use excavators in the 7.6 to 11.5 m; (10 to 15 cu yd) size range. Of these 7, 5 use only excavators in this size range, and they are used to load both ore and waste. 1 of the 7 also uses 11.5 to 17 m' (15 to 22 cu yd) excavators, and I also uses a 17 to 23 m3 (22 to 30 cu yd) excavator. Of the 7 remaining of these 14 precious metals mines that use only hydraulic excavators, 3 use 11.5 to 17 m' (15 to 22 cu yd), 2 use 17 to 23 m3 (22 to 30 cu yd), and 2 use less than 7.6 m' (10 cu yd) units.

Jan 1, 1992

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

The Anshan Iron and Steel Co. (AISC) broke its steelmaking design capacity in 1978, bringing its total production of steel products to 6.86 Mt. Located south of the industrial city of Shenyang, Liaoning Province, in northeastern China, it is by far China’s most important iron and steel complex, ranking twentieth among world centers. The complex represents a unique blend of old ecluipment and new ideas for increased production and improved products. Under a state plan, the Chinese hope to raise capacity to almost 15 Mt/a in the future. Originally started by the Japanese in the early 1920s, Anshan has had a rather turbulent 60-year history. It was disassembled by the Soviets after World War II, only to be reassembled by them in the 1950s. Production was also suppressed during the Cultural Revolution. Since the present-day organization, AISC, emerged, the center has experienced progressively improving conditions as well as increased production. Today, the center includes 10 blast furnaces, 24 open hearths, and two basic oxygen units, designed for 7 Mt/a ironmaking and 6.5 Mt/a steelmaking. In addition, it has six batteries of cokemaking facilities with combined 4.4-Mt/a capacity. Solid Iron Resources Anshan’s iron resources consist of a proven reserve base of over 7 Gt of 30~0 Fe, according to Kao Yang, president of the Anshan Iron Mining Co., a subsidiary of AI SC, Most of that, he continued, is amenable to surface mining. Five major mines located to the north and northeast of the city of Anshan are the principal iron ore producers. These mines trend in a somewhat circular manner and combined, represent an estimated 28.6 Ylt/a of ore capacity. In addition, some 2.2 Gt of magnesite, a necessary ingredient in steelmaking, are also part of the reserve base, according to Kao. Annual production is around .2 Mt/a of 47% magnesite, well over the steelmaking center’s annual requirements, Excess production is shipped to other steel-making centers. The largest of Anshau’s open-pit mines is the Chitashan operation with a design capacity of 8 Mt/a. Ore reserves here are well over a billion tons of 30% Fe. Earlier plans to expand production at this mine to 15 Mt/a, with the help of US Steel, have been temporarily shelved. The other mines in the district and their rated design capacity are: Kungchangling, 7 Mt/a; Donganshan, 6.4 Mt/a; Dakushan, 4.2 Mt/ti; and Yenchienshan, 3.0 Mt/a. The Kungchangling mine is the richest in terms of ore grade at 6076 Fe. Reserves are somewhat smaller at 100 Mt. The unit also operates a small shrinkage stoping operation. Ore grade at the other mines is usually 30-327. Fe. Llost mines operated at reduced capacity during 1979 owing to a natural gas shortage at the mills. The general

Jan 3, 1980

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined to determine through evaluations in two mining companies whether it would achieve measurable improvements. This volume describes the model, how it was applied in the field, and how it was evaluated. Anecdotal data to illustrate common kinds of safety problems and their solutions are included. The literature and field research that preceded the model definition is discussed in Vol. 2, which covers the period of September, 1980 to September, 1981.

Jan 1, 1983