Search Documents

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By J Seppelt, B Akerstrom, A Rice, J Bubnich, T Waters

The Concentrator 1 plant at Cadia transitioned from Cadia Hill open pit to the Cadia East block cave ore body in 2013. As a result of this change, major plant upgrades were required to achieve the desired throughput while treating more competent ore. The 40-foot (40’) SAG mill now receives a feed of predominantly high pressure grinding rolls (HPGR) product with a minor component of secondary crushed ore at a combined F80 of 17 mm. The significant reduction in feed size to the SAG mill has markedly changed the operating characteristics of the mill, which has been extensively studied since commissioning in 1998.This paper examines the operation of the 40’ SAG mill in its new configuration in the Concentrator 1 circuit. Operational stability is highlighted as a significant factor in delivering mill performance, which has been achieved through several key improvement projects utilising a theory of constraints framework. Five years of successful project implementation has progressively lifted the maximum processing rate of Concentrator 1 from the design estimate of 2455 t/h to above 3000 t/h. CITATION:Waters, T, Rice, A, Seppelt, J, Bubnich, J and Akerstrom, B, 2018. The evolution of the Cadia 40-foot SAG mill to treat the Cadia East orebody: a case study of incremental change leading to operational stability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J. Hop, A. Støre, T. Foosnæs

The carbon cathode for aluminium electrolysis is also part of the container of the process. In order to understand the behaviour and possible failure of the cathode, detailed material properties under operating conditions are needed. The paper reports experimental studies of bath and sodium in filtration, graphitization with time, loss of strength due to sodium, sodium expansion as function of pressure, as well as creep due to the developed stresses. As an example, sodium and thermal expansion data are used to calculate strain-stress models of realistic cell designs, and possible design weakness can be pointed out. Keywords: carbon, cathodes, sodium expansion, strength, graphitization, creep

Jan 1, 2004

By R Aseervatham

The fast tracked mine development strategy attempts to blend feasibility studies and engineering/commissioning functions into a streamlined process. In this compressed process, environmental issues are difficult to control with respect to the optimisation of operational environmental performance. This paper presents a standard mine development process with specific focus on environmental issues, and contrasts this against Rio TintoÆs recent fast track experiences on the Hail Creek project (Australia), the Baranj project (India) and the Gokwe North project (Zimbabwe).

Jan 1, 1999

By L. R. Herrmann

The most fundamental feature of fracture is that it involves separation. Such separation can arise by either separation of molecules, more or less along the line joining their centers (tension), or by d sliding separation roughly perpendicular to that line (shear). Theoretically, a perfect crystal could never be broken by the application of perfectly axial compressive stress (until some sub-molecular actions occur). In tension fields the calculated forces between molecules are extremely high. Consequently, calculations based on the forces known to exist in materials at the molecular and crystalline levels always lead to strengths which are two or three magnitudes higher than the strengths obtained in service or in the laboratory. It has been a major problem, therefore, to explain: (a) How fracture can occur in compressive stress states. (b) Why the observed strength of a material is always much lower than its calculated strength.

Jan 1, 2012

The Effect of Using Different Comminution Procedures on the Flotation of Platinum Group Minerals The use of High Pressure Grinding Rollers (HPGR) has been widely reported to have major benefits in the treatment of minerals such as iron ore and diamonds. To date there have been few investigations into its use in the treatment of ores containing Platinum Group Minerals (PGMs). HPGRs are known to reduce energy consumption and wear costs and improve the throughput in the circuit. In the present investigation the effect of the comparative use of HPGR and conventional crushing in combination with either dry or wet rod milling on the flotation of PGMs was studied using batch flotation. Previous studies of a base metal sulfide ores had shown that either HPGR or conventional crushing followed by dry milling produced the highest grades and recoveries. However in the present study it was observed that a similar treatment produced the worst results and the highest grades and recoveries were obtained for the case of conventional crushing in combination with wet milling. The HPGR showed no advantages in terms of flotation performance and dry milling produced particularly poor flotation results. The results were investigated further using various surface characterisation techniques in order to determine the reason for the decrease in grades and recoveries of platinum when using dry milling and HPGR as opposed to the case for base metal sulfides. The feed and product samples were analysed using ToF-SIMS, XPS and MLA. The paper will propose reasons to explain the different flotation behaviour of the two ore types following the various comminution processes focusing on the surface characteristics of the ores, the particle size distribution and the pulp chemistry.

Sep 13, 2010

By R. Dekkers, J. Plessers

The feasibility of using hydrogen to obtain clean steels is investigated. High hydrogen contents are generally considered as detrimental due to the risk of flakes, bubbles and breakouts during casting. Hydrogen can nonetheless be removed by degassing of the steel. The results of industrial campaigns, where total oxygen content and hydrogen content were monitored, are presented. High resolution microscopy of inclusions and laboratory experiments on the rate of inclusion removal by CaO-Al2O3 slags at different partial hydrogen have been carried out. So far, evidence that hydrogen may influence inclusions or the steel cleanliness is not clear. Keywords: hydrogen, cleanliness, inclusions.

Jan 1, 2004

Well designed and maintained haul roads are the key to minimising truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often diff cult to achieve. Poorly designed and built roads exhibit high rolling resistance - a one per cent increase in road rolling resistance can typically reduce speed on ramp by as much as ten per cent - and on the f at by up to 26 per cent. In the current economic climates, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations - simply by virtue of their contribution to overall cost of operations - often in excess of 50 per cent of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled - is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road is designed, and, critically, the interplay between a good design and safe, cost efficient haulage.This paper brief y summarises the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers' requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimise haulage hazards, both from a health and safety perspective. Generally, both objectives have been achieved, but with some specific areas of design and operation still presenting ongoing potential health and safety hazards.The paper then summarises current design guidelines for these safety-critical issues, both from a road-design 'best-practice' and road management perspectives. Implementation of the approach is seen as a basis for reducing the potential of an under-designed mine road to lead to health and safety defects and secondly as a means of giving haul road safety and performance issues greater prominence in the minds of the road-user, operator, mine planner and designer alike.

Dec 6, 2010

By George A. Savanick

Coal mine roof shales fracture preferentially at slickensided surfaces because of weak or nonexistent adhesion between two slickensided rock surfaces. The purpose of this Bureau of Mines research was to characterize chemically the thin film of smooth, glossy material that makes up the slickenside. This material was analyzed by electron spectroscopy and ion scattering spectrometry while in place on the rock surface and by standard methods of quantitative chemical analysis on concentrate removed from the rock. These analyses showed that the chemistry and mineralogy of the slickensides are similar to that of the adjacent shale.

Jan 1, 1974

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

By Thomas A. Giordano

Portable communications equipment is becoming increasingly important in underground mining. Proper selection of microphones and hearing devices to be part of these communication systems is essential if the messages are to be transmitted intelligibly. In this program a thorough study of the requirements for these transducers was made with respect to intelligibility, mechanical configuration, human factors and safety. A computer analysis was made to predict how several combinations of transducers would perform at typical mining noise levels. A survey has been made of those microphones and hearing devices on the market today that might be applicable to the miner communication system. Several systems are proposed and evaluated.

Jan 1, 1976

By J. D. Miller, C. L. Lin

Filtration of fine particles involves filter cake formation and removal of surface moisture by drawing air through the porous structure. Accurate assessment of the transport properties of porous media (in this case, filter cake) is of major importance in the development of improved filtration processes. Implications from these studies are important in the design and operation of filtration equipment in order to enhance the efficiency of this important solid-liquid separation process. The microstructure and connectivity of pore space are important features necessary to describe detailed fluid flow phenomena in filter cake during fine particle filtration. In this regard, 3D characterization of pore structure is essential. The pore structure has to be described by parameters which are of special relevance to the interpretation of fluid transport phenomena. These parameters should be based on directly measured variables of the pore system and not inferred from indirect variables (such as those determined empirically from transport processes) valid only for a particular pore structure. In this way fundamental relationships between pore structure and fluid transport at the microstructure level can be described. In order to achieve this level of sophistication the three-dimensional interconnected pore structure of filter cake must be determined. Study of fluid transport phenomena in filter cake using x-ray microtomography to characterize the complex three-dimensional pore geometry is discussed. On this basis the Lattice-Boltzmann (LB) method is used to simulate and to establish a fundamental relationship between pore microstructure and effective transport coefficients.

Jan 1, 2002

By D J. Black

Ventilation modelling is used to evaluate ventilation system performance. This paper describes modelling to assess potential changes to a single entry longwall ventilation circuit to improve ventilation and gas management. The longwall panel is extracting a 215 metre face in a 1.5 metre coal seam at a depth of 900 to 1000 metres below surface. The 1.5 metre B seam is located approximately 25 metres below the main 3.0 metre A seam and the gas content of both coal seams is approximately 20 to 25 m3/t. The B seam is extracted prior to the A seam and the mine relies on fracturing of the overlying strata to induce gas emission from the A seam to reduce the gas content prior to mining. Longwall operations in the B seam are constrained by limited ventilation and high gas emissions. Due in part to statutory limits on gas concentration and air velocity, the average longwall production rate is approximately 700 t per day.Gate roads in the B seam are single entry, developed using road headers and supported with steel arches. Additional timber cog support is installed to reduce roadway closure from abutment loading. Due to the slow advance of gate road development, mine management were reluctant to consider significant mine design changes, such as two heading gate roads; therefore, the investigation focused on determining the extent to which ventilation and gas emission impacted on longwall production performance, while recommending short-term, low-cost actions to improve ventilation and gas management to support increased longwall production.CITATION:Black, D J, 2017. Application of modelling to improve ventilation and gas management in a single-entry longwall panel, in Proceedings Australian Mine Vent Conference 2017, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A. D. Pelton, Y. -B. Kang, S. A. Decterov

Computerized thermodynamic databases for solid and liquid metal, slag and solid oxide phases in the Al2O3-CaO-CoO-CrO-Cr2O3-FeO-Fe2O3-MgO-MnO-NiO-SiO2-S system have been developed by critical evaluation/optimization of all available phase equilibrium and thermodynamic data. The databases contain parameters of models specifically developed for molten slags, liquid steel and solid oxide solutions such as spinels, pyroxenes, olivine, monoxide (wustite, periclase, lime), corundum, etc. By means of the optimization process, model parameters are found which reproduce all thermodynamic and phase equilibrium data within experimental error limits. Furthermore, the models permit extrapolation into regions of temperature and composition where data are not available. The databases are automatically accessed by user-friendly software that calculates complex equilibria involving simultaneously slag, metal, refractories and gases, for systems with many components, over wide ranges of temperature, oxygen potential and pressure. A short review of the available databases is presented. The critical evaluation/optimization procedure is outlined using the Al2O3-CaO-FeO-Fe2O3-SiO2and Al2O3-CaO-MnO-SiO2systemsas examples. Several applications of the databases to deoxidation of iron and to inclusion control in steel are discussed. Keywords: thermodynamics, phase equilibrium, phase diagrams, databases, ferrous metallurgy, steelmaking, inclusion control, slags, oxide systems.

Jan 1, 2004

Lower Miocene Maryville Coal Measures at Waitewhena Coalfield, in the Taranaki coal region, include seams of sub-bituminous coal up to 4 m thick. During coalfield exploration Fletcher Challenge Ltd drilled ten cored holes, all of which encountered at least one seam. Coal quality is variable. Ash ranges from six to 12 per cent and sulphur from 0.5 to three per cent. A basal seam, overlying the Lower Mokau Sandstone, appears to extend throughout the area under investigation. A rider seam, of variable thickness, closely overlies the main seam in most drillholes. The rider converges with the main seam to the north and vertical trends in coal properties suggest that the seams are united in some locations. A less extensive seam sometimes occurs at the top of the coal measures beneath the Upper Mokau Sandstone. The lithostratigraphy of the intervening coal measures is complex, and coexistence of fluviodeltaic, lagoonal/lacustrine, and marine depositional environments is provisionally inferred. Lateral variations in coal properties (clastic derived ash, volatile matter, inertinite, hydrogen), thickness of the sedimentary parting between the basal seam and rider, texture of the coal measure sediments, and distribution of the upper seam all indicate persistence of a relatively low lying northeast-trending zone which may have been structurally controlled. Available data indicate that coal measure accumulation was terminated by marine transgression from north to south.

Jan 1, 1987

By M. Verri

[ ]

Jan 1, 2009

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

A preliminary study was conducted by the Bureau of Mines to determine the effect of humidity on salt mine airborne dust levels. Results showed less dust where the humidity was elevated. Dust reductions appeared to be dependent on the equilibrium between humidity and salt.

Jan 1, 1980