Search Documents

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By David Reddick

The mining industry is in the midst of dramatic change. Mining activities are moving from industrialized first world countries (Canada, Australia, and the United States) to the third world. This shift is occurring due to depleted reserves, tough environmental standards, and expensive labor in traditional mining countries. During a recent trip to South Africa, I was asked, owing to my educational background in economics and an international involvement in drilling and blasting, what changes could be anticipated in third world blasting practices as labor costs increase. It is from that beginning that this presentation has evolved.

Jan 1, 1997

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By G. Konak

In-pit crusher location selection has had an important role recently, since increasing diesel prices. One way of reducing the haulage costs is to shorten the truck haulage distance by bringing the truck dump point into the pit. This study covers the work done on the optimum crusher location definition for a company that produces aggregate near Izmir, a city of Turkey located in the west. This paper will discuss the effects of pit geometry and mine access requirements on optimum crusher location selection that are mainly based on the establishment of minimum haulage distance. The method will be introduced first and then the computer algorithm developed for this study will be discussed later in the paper. Keywords: in-pit crushing, optimum location selection, optimizing haulage, computer aided design.

Jan 1, 2007

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

By J. Maheu

Heap leaching is an old technique for the recovery of copper, but a fairly new technique for the recovery of gold.The paper outlines the equipment required for the establishment of heap leaching test facilities and the procedure required to insure meaningful results. Sampling methods, the metal balance, carbon adsorption and stripping and safety procedures are discussed in broad outline.

Jan 1, 1982

By Víctor Cárdenas

El presente trabajo describe el manejo de las herramientas de calidad que aportan a la reducción de riesgos en la compañía minera La Poderosa. Para determinar los defectos, causas y consecuencias, es necesario conocer el procedimiento de control de los mismos a través del diagrama de Ishikawa o el ciclo de PHVA. Esta metodología permite encontrar la solución a los problemas dentro del aseguramiento de la calidad, seguridad y productividad de una empresa, así como establece la fuente de la causa de los accidentes por lesiones, como de los daños a la propiedad privada. En consecuencia, su aplicación se ha estandarizado en las áreas de seguridad y medio ambiente de dicha minera desde hace dos años, obteniendo resultados muy satisfactorios como el Premio Nacional de Seguridad en minería subterránea otorgado por el ISEM.

Sep 13, 2001

By N. Mejia, Z. Xiao, D. Fragomini, A. R. Laplante

"The adaptation to platinum-group minerals (PGMs) of a protocol developed to predict gold recovery by gravity is presented. The protocol is based on three different data sets: ore characterization of gravity-recoverable minerals, description of their behaviour in cyclones and ball mills, and performance of recovery units. Examples of these are given. It is shown that the gravity-recoverable PGM (GRPGM) content can be very high. A case study at the Clarabelle mill is presented. Sperrylite is the dominant platinum mineral, and its partition curve is very similar to that of gold, despite its lower density. Its grinding kinetics is significantly higher than for gold. As a result, sperrylite accumulates in finer sizes than native gold, but can still be recovered by gravity or flash flotation. Recovery projections based on gravity recoverable data are presented.BACKGROUNDReliable modeling of gold recovery by gravity or flash flotation from a grinding circuit is based on the ability to describe the properties of gold-bearing particles in the ore, their behaviour in grinding and classification units and the performance of the equipment used for recovery, be it gravity or flotation. This is shown in Figure 1."

Jan 1, 2004

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By Miguel A. Farfán

El presente trabajo describe los criterios de productividad en el diseño de tajeos para vetas irregulares a través del método de explotación de corte y relleno. Dicho método es factible -en tanto es capaz de captar el desmonte producido por niveles superiores que requieren avances, así como también en los inferiores. De forma que se pueda agregar valor por la función que cumple en la producción sino por las demás actividades. Finalmente, en el caso de los índices de productividad, el control se debe manejar a un nivel de planeamiento que pemita corregir procesos muy costosos, faltos de continuidad y genere equipos parados, tiempos muertos, daño a equipos o recursos.

Sep 12, 2005

By F P. Hao

Organo-sulphur-based collectors (eg xanthates, dithiocarbamates and dithiophosphates) are widely used in the flotation of sulphide minerals. Xanthates (ROC(=S)Sû), for example, adsorb strongly at sulphide mineral surfaces, in a reaction that is electrochemically coupled with the reduction of dissolved oxygen. One of the oxygen reduction products, hydrogen peroxide, reacts directly with dissolved xanthate, leading to its oxidative decomposition. Experimental work has been conducted, using ethyl xanthate, to understand the molecular mechanism by which hydrogen peroxide reacts with xanthates. A number of degradation products have been identified, some of which have not been reported previously. This oxidative decomposition reaction pathway is discussed in the broader context of xanthate decomposition in flotation systems. One of the identified ethyl xanthate decomposition products, ethyl perxanthate (ROC(=S)SOû), has been observed in the process water of a number of mineral processing operations. The interaction of this molecule with goethite (α-FeOOH) particles, typical of that found in tailings dams, has been studied in more detail using attenuated total reflectance (ATR)-FTIR. The ethyl perxanthate molecule has been found to coordinate to iron (FeIII) at the goethite surface, and undergo a surface-catalysed decomposition process. In the presence of both PbII and goethite, a ternary surface complex is formed, where ethyl perxanthate is coordinated directly to surface adsorbed PbII atoms. The results obtained give some insight into the environmental fate of ethyl xanthate in tailings streams, and a basis on which to consider the environmental importance of such species in tailings dams. Strategies for the destruction of residual xanthate levels in waste water streams are discussed in terms of the likely reaction products.

Jan 1, 2002

Possibilities for Flotation Acoustics Monitoring - A Review

Sep 13, 2010

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

By J. H. McKibbon

THE metallurgical industry has purchased more than sixty per cent of the industrial gas cleaning equipment installed in Canada. This includes cyclonic collectors, scrubbers, cloth filters and Cottrell Precipitators. These are the principal types of equipment which are used commercially for the cleaning of gases which result from the processing of iron, nickel, copper, lead, zinc, gold, gypsum and aluminum ores. The recovered dust, which usually contains metal values, is returned to the process. The cost of the equipment is thus economically justified. This is in contrast to other industries, such as those involving steam power generation, asbestos, cement and lime production, where, though dust collection equipment is extensively used, it is installed primarily for nuisance abatement. Communities are becoming more and more conscious of air pollution, new and more stringent legislation is being enacted, and, for other than economic reasons the smelting industry will eventually be required to install more efficient gas cleaning equipment. This paper

Jan 1, 1962

By K S. Fisher, J D. Pease

The installation of the George Fisher flowsheet in the lead/zinc concentrator at Mount Isa Mines Limited has recently been completed. The George Fisher flowsheet involved moving flotation capacity from the lead circuit to the zinc circuit and changes in zinc circuitry, changes in the reagent regime and increased regrinding capacity, using IsaMills, to regrind some streams to 80 per cent passing seven microns. The project was highly successful, delivering a five per cent increase in zinc recovery within a fortnight of commissioning. The George Fisher flowsheet was developed over six years. Laboratory work built upon the knowledge gained from investigating and processing the Mount Isa and Hilton orebodies. The engineering design and construction for the brownfield expansion of the existing lead/zinc concentrator had significant involvement from the operational, maintenance and technical personnel. Experienced personnel were seconded from the concentrator to the design and construction groups to ensure smooth integration of the new flowsheet into the existing concentrator with minimum downtime, and maximising the reuse of existing equipment. The combination of thorough design, good project integration with operations, and a good commissioning plan allowed almost immediate delivery of project gains. The project was highly successful, the full design improvements were achieved within two weeks, allowing the focus to move to developing future improvements.

Jan 1, 2000

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. The IS countries that constitute the region accounted for 26% of world crude petroleum output, 17% of world natural gas plant liquid production, and almost S% of world dry natural gas production. About 66% of total world crude petroleum reserves and 31 % of total world natural gas reserves are in the Middle East. Transportation and port facilities in the region are geared to expediting efficient and rapid shipment of these materials. U.S.-dollar-denominated export sales of these fuels, estimated at $120 billion in 1989, provide funding for further diversification of the mineral industry. This is usually through development of downstream facilities for producing energy intensive metals such as aluminum and byproducts of the fuels such as petro-chemicals and fertilizers. Earnings from the industry are also channeled by sever-al Governments in the region to mineral industry projects in Africa and elsewhere. A fairly wide range of nonfuel minerals is produced in the region. However, the variety of minerals produced, output levels, and the size of the overall nonfuel mineral economy is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, ranked among the top three world producers of boron, chromite, pumice, and strontium. It was also a significant world producer of magnesium com-pounds, mercury, and sodium sulfate. Iran had generally lower output owing to 9 years of neglect to the mining sector between 1979 and 1988. It was a significant producer of gypsum and fifth in world production of strontium. Despite a very small domestic mineral industry, Israel was second in world production of bro-mine and a significant producer of phosphate rock and potash. Jordan ranked fifth in world production of phosphate rock. Iraq ranked about eighth in world production of sulfur, a commodity of major importance in the metallurgical, petrochemical, and fertilizer industries.

Jan 1, 1992

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By W. C. Hudson

"Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2Si05) and are used in the ceramic industry for the manufacture of high-grade refractories. ""Natural sillimanite with added corundum or other alumina to just short of mullite 2SiO2) proportions is unequalled for jobs where strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags is desired. High-grade porcelain ware also requires these minerals.""At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite has given economic preference to kyanite or andalusite for special refractories and high-grade porcelain ware.""3/The possible economic value of the sillimanite schist in the piedmont Plateau was first recognized by Dr. L. L. Smith, of the University of South Carolina, who published an article in the Engineering and Mining Journal, August 1943, on an occurrence of sillimanite schist in South Carolina.The Bureau of Mines was interested in developing a large source of sillimanite to relieve the shortage of high-grade refractories, and initiated a project to locate the ore-bearing areas in Georgia and South Carolina and to develop the most favorable ones.Two hundred and seventy-eight outcrops of sillimanite-bearing schists were found by a Bureau of Mines engineer.4/ The schist occurs irregularly throughout a belt extending from Talbot County, Georgia; to Spartanburg County, South Carolina, about 220•miIes long and approximately 15 miles in maximum width. The Bureau drilled four areas of the more coarsely crystallized schist in Georgia and South Carolina:In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon; chief; conducts preliminary examinations, performs the actual exploratory work; and prepares the final report. The Metallurgical Branch;.R. G. Knickerbocker; chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Sep 1, 1946

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008