Search Documents

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

Komatsu America has introduced its 2-MW (2,700-hp), 930E-3 ac electric drive truck with a 290-t(320-st) capacity. The truck is designed to provide increased productivity, lower cost per ton hauled and improved speed and control. The 930E-3 is powered by a Komatsu SSDA16Vl6016-cylinder engine. It is capable of speeds up to 65 km/h(40 mph) and is a 15-percent to 20-percent more productive unit than 218-t (240-st) trucks, at a lower operating cost per ton. The 930E-3 also provides enough torque and speed to get up and off ramps easier than mechanically driven trucks. And it can climb at altitudes up to 3,650 m(12,000 ft) without any fuel deration.

Jan 1, 2004

By Christopher W. Corti

A major aim of the GOLD 2003 conference, is to promote new gold related science and technology with a view to developing new useful industrial applications for gold. Current industrial uses have provided a steady annual industrial demand for gold of around 350-400 tonnes in recent years, the bulk of which is centred on electronics applications, with dental uses constituting the second largest application. However, there is good reason to believe that whilst gold will continue to play a major role in these sectors in the future, substantial growth of demand is not anticipated. Increased industrial demand for gold is only likely to come through the emergence of new applications, probably most significantly in five broad market sectors: ? Pollution and emission control technologies, including fuel cells. ? New uses for gold in advanced electronics, electrical systems and devices. ? Chemical processing of a range of bulk and speciality chemicals, using gold based catalysts ? Advanced coatings exploiting the novel properties of gold, particularly in nanoparticulate form. ? New biomedical uses for gold including medical treatments, drugs, implants, sensors and devices. There is cause for optimism that many new applications for gold could emerge in these sectors over the next decade and that this will lead to a substantial growth in demand for gold. It is clear that many of these new opportunities will be based on a chemical approach to synthesis of useful products rather than what has historically been a materials or mechanical approach. To turn this expectation into reality requires sustained support of R & D and a determination to exploit this new science and technology into viable commercial applications.

Oct 1, 2003

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By K. Park

Coupled influence of sulphidizers and xanthates on the electrokinetic property and flotation behavior of malachite was systematically examined via electrophoretic mobility measurements and microflotation tests. The electrophoretic mobility results for the malachite before and after surface modification with different types (Na2S and (NH4)2S) and amounts (1×10-7?1×10-4 moles/g) of sulphidizers, showed that the isoelectric points (IEP) of malachite differed at the low dosage level depending on the type of the sulphidizer, which ranged between 5 and 9.5. However, the IEP values were observed to be shifted from high to low pH values with increasing amount of sulphidizers and finally ranged between 3 and 4, indicating that the sulphidizers played a different role on changing the surface property of malachite. In order to further understand the effect of sulphidizers on the electrokinetic property and flotation behavior of malachite in a sulphidizer+xanthate system, flotation tests were carried out with malachite sulphidized with Na2S and (NH4)2S (adsorptive amount=8×10-5 moles/g) at different bulk xanthate concentrations. The results showed that the flotability of (NH4)2S-treated malachite was greater than Na2S-treated one over the entire xanthate concentration investigated, indicating that the type of sulphidizers played important role in malachite flotation; however, no obvious correlation between electrokinetic property and flotability of malachite was observed.

Feb 27, 2013

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

By Albert Adu-Acheampong

Fairmount Mineral's Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008

By S. Hamilton

Borates are essential to life, and to many products that are essential to an acceptable standard of living. They occur naturally in seawater at an average concentration of five milligrams of boron per liter. Fresh water lakes, rivers, streams and ground water generally have concentrations of about one milligram boron per liter. Borates are also present in soil at concentrations ranging from 0.1 to three milligrams of boron per kilogram. Because most of that boron is locked into insoluble minerals, clay or organic matter, boron deficiency is more widespread than boron enrichment. Borates evaporate into the atmosphere from seawater, rain, snow and hot springs. In rain and snow, natural boron concentrations range from 0.002 and 0.1 milligrams boron per liter. All told, boron moves through the atmosphere at a rate of 5 Mt to 7 Mt/a (5.5 million to 7.7 million stpy).

Jan 1, 2005

On the Kinetics and Equilibrium Models for Biosorption of Ni(II) onto a Gram-Positive Bacteria Strain, Rhodococcus opacus, for Environmental Applications The aim of this fundamental study was to evaluate the biosorption of Ni(II) from aqueous solution streams onto a Rhodococcus opacus strain through kinetics and equilibrium isotherms studies. The biosorption of nickel achieved its highest value in a pH around 5. The experimental data evaluation was carried out focusing three two-parameter models, as: Langmuir, Freundlich, Dubinin - Radushkevich. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Freundlich model fits better the nickel biosorption data. Maximum uptake capacity of nickel reached a value around 7.63 mg.g-1 for R. opacus. The biosorption rate was fast and achieved a removal of around 79 per cent of Ni(II) in the first 5 minutes at room temperature (25 ¦ 2¦C). The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). The error analysis established that the pseudo-second order model better fits the data.

Sep 13, 2010

I am wearing two hats today. When the invitations went out to participate in this forum, two were received in the head office of the Department of Lands and Survey - one addressed to the Director-General of Lands and one to the Chairman of the National Parks Authority. It seemed logical that as the department is responsible to the Government for the administration of the National Parks Act 1952, we should respond by providing one speaker to cover both the department's interests and those of the National Parks Authority. I hope, however, that this will not blur the clear distinction which exists in the context of the mineral industry between Crown land on the one hand administered by the department for the statutory Land Settlement Board and national parks and allied reserves on the other hand which are the responsibility of the National Parks Authority.

Jan 1, 1976

Three computerised sets of minerals information are being developed by New Zealand Geological Survey in co-operation with the Resource Management and Mining group of the Ministry of Energy: 1. Geological Resource Map: a file of information on the location, geology, geochemistry, production, and potential use of individual occurrences of aggregate, mineral, geothermal, coal, oil, and gas resources. The computer program can be used for search and retrieval of information and the production of maps and tables. The data is being published as a series of 1:250 000 maps with accompanying text and tables. 2. Minerals Bibliography: an index and retrieval system for mineral exploration related; open-file company reports, N.Z. Geological Survey files, scientific research publications and university theses. 3. Minerals WhoÆs Who: an annotated directory of geologists involved in mineral exploration, mining and research.

Jan 1, 1986

By F. C. Lendrum

"This paper had its origin in a panel discussion organized by the Canadian Uranium Producers Metallurgical Committee (CUPMC) at their Annual Meeting in Blind River in May, 1964. The reason for the panel was the formation of the National Uranium Tailings Research Program funded in the amount of ten million dollars by the Federal government. According to the bureaucrats in charge the program would seek to solve the perceived problems as well as any actual problems they believed existed with uranium tailings. Dr. Allan Ashbrook of Eldorado Nuclear chaired this panel and his summation of the panel's purpose was set out as ""Regulation and the Regulatory Process in the Nuclear Industry, Where Have We Been, Where Are We Now and Where Are We Going""?"" This paper will try to relate these questions to the whole mineral industry.The Canadian Mining Association has been telling us our natural resources are today required only if they are competitively priced with those produced in so called ""third world"" countries where labour rates are lower, environmental restrictions may be less and every effort is made by the local government to sell their product. It is in this hostile economic climate that the Canadian mining industry now finds itself. Before going further I want to stress these comments apply only to: a) Mines financed by private capital in a free enterprise society.b) Mining companies want to operate in an environmentally safe manner. However, they must earn a profit because no company financed with private capital can borrow money ad infinitum.WHERE HAVE WE BEENNone of us today would want to return to the days when the mill waste management system consisted of pumping the tailing to the nearest slope and letting nature's law of gravity do the rest. This was the way it was in early gold mines in Nova Scotia, tin mines in Cornwall, England or silver mines in Cobalt, Ontario and survives today in countries where climate, customs and methods of doing business are far different from Canada. As mill tonnage rates increased, more sophisticated systems evolved often designed for mining areas with different climates. Systems imported from arid climates such as south-west United States retained the solids but allowed bacterial oxidation of the sulphides promoting acid drainage. Environmental regulations were introduced and Canadian mines learned to handle tailings in our climates."

Jan 1, 1986

By K. Oraee

Mining of copper ore and the related industries play an important role in Iran?s economy. Copper ore production in Iran accounts for 75% of the total production in the Middle East. All activities related to copper, that is, exploration, production, refinement etc are owned and managed by state owned companies. Decisions have been made to privatize all these activities. To assess the success of this privatization process, different components of the industry must be subject to economic analysis. In this paper, the cost estimation of all operations has been carried out. The total potential and attainable revenues have also been estimated using historical data available from the industry. Risk is a major factor in all mining activities and the copper industry of Iran has been subject to risk factors arising from many internal and external variables. These variables have been recognized and their effects evaluated. The effect of risk on the economic feasibility of the operations in the industry has also been analyzed.

Jan 1, 2011

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By H. S. Marshall

Optimum Colliery is an opencast strip mine producing 18Mt of bituminous coal per annum for the export and inland markets as well as for domestic power generation at the Hendrina PowerStation. Coal is exposed by four 60m3 and four 11m3 walkingdraglines and transported from the open cuts to the processing plants by twelve 130 ton coal haulers. Overburden and interburden areas are drilled by nine 250mm-diameter rotary drill rigs. Until 1997 all surveying tasks were conducted by electronictotal stations requiring accurate control points from which line-of-sight XYZ readings could be taken. In 1997 a GPS system was introduced which consisted of a fixed base station and two rovers. The rovers were able to perform most of the survey tasks assigned to total stations. In addition, two overburden drills were equipped with blasthole drill navigation systems, which includes the drill monitoring and material (strata) recognitions system. The rest of the drilling fleet will also be equipped with GPS systems. Blasthole positions are designed in the office based on survey and geological/geophysical information and transmitted via radio link to an industrial PC on the drills. Together with GPS positional data, both the planned and actual drill positions are displayed on an LCD screen. This eliminates the need for surveyed hole positions to be staked before drilling, and for actual hole positions to be surveyed after drilling. As holes are drilled, performance and rock property data transmitted back to the office. Future applications will include GPS monitoring of dragline positions and pad elevations. GPS receivers on the draglines will utilize the existing base station to calculate and transmit XYZ co-ordinates. Another application will be locating of boreholes in the field prior to the pumping of specified explosive charges into the blastholes. Charging instructions for each blasthole will be loaded into the computer on the explosives truck which will be equipped with a GPS system for hole identification.

Jan 1, 1998