Search Documents

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008

By P. Anyon

Exposure to the microscopic particles in diesel engine exhaust can lead to serious health problems, including the incidence of cancers, heart disease and increased susceptibility to respiratory ailments such as pneumonia, bronchitis, and asthma. In Australia, mining companies and state government authorities are actively responding to this major occupational health and safety issue. Their initiatives place considerable emphasis on routine monitoring of diesel particle matter (DPM) exhaust emissions, both for engine benchmarking and as a part of routine engine maintenance. Implementation strategies follow two complementary paths: determination of individual engines? emission signatures combined with periodic engine re-certification; and co-operatively agreed industry-government engine maintenance programs, which are subject to audit. Both strategies place heavy reliance on real-time measurement of DPM concentrations in engine exhaust, using ruggedized instrumentation, mainly based on laser light scattering photometry. Adding value to this cooperative approach, industry has also collectively funded a government agency to design and manage a database, into which the results of all-routine DPM testing can be uploaded directly by individual mines. This win-win outcome is a great example of how cooperative action between governments and industry can deliver the goods: in this case, a safer working environment, more efficient energy use and the capacity to benchmark performance with industry peers.

Jan 1, 2009

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

By Aleksandar D. Bugarski, Robert J. Timko

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

By Marlyn King, Kevin Peterson

Power Decks are voids created in the bottom of the borehole through the use of a suspended Super Plug. Explosive energy is started downward at initiation creating high pressures which find relief at the comers of the borehole cylinder in the bottom of the hole. This relief creates a horizontal break to the neighboring boreholes - the same effect as presplitting. This “presplit” represents a change of mass to.the explosive energy,and it is reflected upward in the more efficient form of tensile waves. This provides better use of the explosive energy than compression waves. This technique has created a new way of looking at the ways that explosive energy is transported through the rock mass.

Jan 1, 2002

By H. Akbari

The ordinary Portland cement (OPC) is the key pozzalonic component of the concrete mix, widely used as the construction material world-wide. Billions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of CO2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic CO2 emission each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon foot print of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the non-metallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned to extract some of the valuable metal oxides from fly ash prior to using the major non-metallic portion of the fly ash for geopolymer concrete application. The results obtained from this study exhibited that the compressive strength of the geopolymer concrete compares favorably with that of the conventional concrete prepared using the OPC.

Feb 27, 2013

By Dr. G. R. Hoey

"Abrasive wear and corrosive wear of carbon-steel grinding balls occurred simultaneously during the wet-grinding of hematite iron ore, and Ni-Cu sulphide ore, in laboratory ball mills. Two corrosion control methods, the use of corrosion inhibitors and pH control, were investigated and found to be effective means of reducing or preventing corrosive wear. Up to 50 % reduction of total ball wear resulted from the use of these methods.Corrosive wear is caused principally by the reaction of oxygen in air with the carbon-steel grinding balls, probably by the following reaction: 2Fe + O2 + 2H20 - 2Fe2 + 40H-.IntroductionA survey of corrosion problems in Canadian sulphide ore mines was completed and the findings were published in 197l(l). The corrosion survey was used to develop the present research program with the objective to find more economical and effective ways and means to reduce the corrosion that occurs in the mining and metallurgical industry. The purpose of this presentation is to review the projects being done by staff members of the Corrosion Section, Extraction Metallurgy Division, on corrosive wear and its control in wet-grind ball mills.Both abrasion and corrosion contribute to metal consumption during wet grinding of ores. The total wear of grinding media in this study is assumed to be equal to the sum of corrosive wear and abrasive wear. A great deal of research and development has been reported in the literature on ways to improve the abrasion resistance of grinding media but only a small number of studies has been reported on the corrosion resistance of conventional grinding media."

Jan 1, 1974

By S. M. Moore

Technological advances in underground coal mining have reduced fatalities but may not have reduced worker exposure to cumulative injury risk factors. The objective of this study was to evaluate the prevalence of cumulative injuries before and after the implementation of technological advances in underground coal mining and to make a general cost estimate for these injuries. A previously published algorithm was utilized to identify cumulative injuries within the Mine Safety Health Administration (MSHA) database for two data sets: 1983-1984 and 2003-2004. For both, the following were determined: the number and percentage of cumulative injuries, the average days lost, the average age at the time of injury, the average years of experience and the general cost estimate by body part. The percentage of cumulative injuries remained largely unchanged (37 percent in the 1983-1984 period and 33 percent in the 2003-2004 period). The average number of lost days due to cumulative injuries increased (36±55 days and 62±82 days, respectively), which may have been due to the increased worker age (seven years older in the 2003-2004 period), increased length of employment (seven years longer in the 2003-2004 period) or other factors such as changes in medical practices. Cumulative injuries to the back decreased by 10 percent, while cumulative injuries to the knee increased by 8 percent. The reduction in back injuries may be due to the implementation of assist devices, while the increase in knee injuries may be related to kneeling/crawling in low-seam mines. Cumulative injuries were found to remain a major financial burden on the industry. Recently, National Institute for Occupational Safety and Health (NIOSH) developed tools to assist mining companies with incorporating an ergonomics process into their existing health and safety programs. The participating companies have reported tremendous success. Therefore, it is recommended that ergonomics processes be implemented as a means to systematically identify and address the root causes to cumulative injuries and ultimately reduce costs.

Jan 1, 2008

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

Although small scale mining is regarded by many as of historical value only, this kind of mining activity is still much more widespread than is usually assumed. It has been estimated that it produces as much as ten per cent of the global mineral output. More significantly this figure is often much higher for many of the developing countries of Africa, Asia and South America, signifying the relatively greater contribution of small scale mining to the economies of those countries. It is also noted that small scale mining has always been a feature of mineral production in New Zealand and Australia. An attempt is made to define small scale mining, and the factors determining the suitability of small scale mining operations are discussed. The state of the art in small scale mining is reviewed and the author endeavours to rationalise the important parameters which contribute to successful small scale mining operations and discusses how these parameters may be optimised. The benefits of small scale mining to the mining industry as a whole and to the community at large are outlined. The paper concludes by emphasising the necessity to maintain small scale mining and 'explores' its future 'prospects'.

Jan 1, 1990

By Raja V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. An investigation was conducted of current mined-land planning practices to aid in the development of a procedure for evaluating postmining land use potentials. This investigation considered both the industry and public planning approach to mined-land planning. It included a detailed review of the impact of regulation, factors that determine land use, and current site planning methods employed by the mining industry. The methods of this investigation included three in-depth case studies of surface mines in the eastern, central, and western United States. A site planning pro-cess has been developed and applied to the surface mine case studies to evaluate the economic, environmental and social impacts of postmining land use alternatives. In add it ion, guidelines are proposed to enhance the cooperation between local land use planners and surface mine planners, as well as to improve comprehensive planning with regard to mineral resources at the local and regional level.

Jan 1, 1983

By M. D. Aldridge

The results of designing, constructing, installing and operating a ventilation monitoring system throughout an entire commercial coal mine is presented. Measured parameters were airflow, methane, carbon monoxide, temperature, relative humidity and differential pressure. A central computer provided for automatic system operation. Preliminary tests of two remotely controlled ventilation regulators were performed in conjunction with the monitoring system.

Jan 1, 1977

This report is a compilation of all information obtained in accordance with the requirements of contracts S0122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies: Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gai-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated

Jan 1, 1974

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By J E. Askew

The rapid expansion of gold production in Australia over the last five years can be attributed in part to the development of selective mining techniques for open pit gold operations. These techniques allow an increase in head grade with a substantial reduction in mill feed tonnage, as compared with traditional open pit designs. As a result, the capital requirements for mine development and mill construction are substantially reduced, improving the cash flow profile in the early years of operations. To put such a design into effect, the emphasis of mine production must be on producing gold, rather than tonnes of ore. Mine planning at Martha Hill has been based on such a philosophy. After the quantity and grade of the resource had been defined, the exploration programme was increasingly concerned with the local variability of ore zones, and with determining the position of values within broad ore-definition envelopes. The purpose of this work has been to allow the prediction of the tonnages and grades achievable from various levels of the pit when mining selectively using hydraulic excavators. The studies have so far indicated that the Martha Hill deposit can be mined selectively during the early years of production. The additional costs for detailed grade control and a reduced digging efficiency are more than compensated by the exclusion from the mill feed of much valueless material.

Jan 1, 1986

By Christopher Cloete Uys, Luis Manuel Poinha Valentim

The purpose of this workshop is to describe and demonstrate the use of SPEEDWAVE, a high speed data recorder, its VOD enhancements, and the software which binds the system together. The system was designed by TLC Sohware, SOUTH AFRICA. TLC is a company spedalising in the solution of engineering problems, using computertechnology as a base. TLC was founded in 1987, and has since been involved in many different.measurement, control, simulation and modelling projects. Wth respect to the blasting industry, TLC has, in conjunction with AECI South Africa/ICI, developed a tunnel mining design aid, a ring blasting design aid, a multkhannel seismograph and a laser surveying program. In 1989, TLC designed and built the BA800. a microcomputer-based high speed recorder. These recorders are still in use and are producing valuable results. Based on improved technology and with the field experience of the BA800, TLC has designed and developed the data recorder SPEEDWWE.

Jan 1, 1995

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

Two Variable Real-Time Algorithm for Cone Crusher Control

Sep 13, 2010

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005