Search Documents

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By A. J. Rigby

Refractory linings in converters or anode furnaces used to over-oxidize the blister copper will suffer rapid deterioration, due to prolonged contact with copper oxide-rich slag. Nitrogen stirring with COP KIN porous plugs and use of SEMTECH OPC in converters and anode refining vessels can considerably reduce both refractory wear and processing times. In addition, careful control of the vessel atmosphere and the use of real-time optical process control minimize both slag volume and contact time with the vessel refractory.

Jan 1, 2005

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By J. Brasfield

Jim Walter Resources, along with the Rock Mechanics Branch of British Coal and Strata Control Technology Pty. Ltd., is presently studying the yield-stable-yield pillar design in use at the Blue Creek No. 7 Mine located in Brookwood, Alabama. This paper describes the steps taken to determine stresses on the strata surrounding the pre-driven development entries. It also describes the installation and monitoring of stress cells and extensometers used to quantify the stress build-up and strata movement associated with the headgate pass of a longwall panel. The findings of this study will be used to design and predict the performance of a 2 entry yield pillar system in the Parkgate Seam at Welbeck Colliery in the United Kingdom. Stress measurements and strata movement data from No. 7 Mine and Welbeck will be used to develop a computer model that can predict the performance of such a pillar system in British mines. Jim Walter Resources will use this data to study the performance of the present yield-stable-yield pillar system in order to determine if conditions will allow the stable pillar width to be decreased while maintaining current standards of safety and production.

Jan 1, 1994

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By R. G. Cawthorn

The earliest authenticated scientific report of the occurrence of platinum in rocks from the Bushveld Complex appears to be by William Bettel on 10th November 1906. Thereafter, prospecting of the chromite-rich rocks for platinum proved frustrating. I suggest that the resurgence of interest shown by Dr Hans Merensky in 1924 resulted from his realization that newly-panned platinum had a different grain size from that in the chromite layers and indicated a different source rock, which he located and it became known as the Merensky Reef.

Jan 1, 2006

By A B. Christie

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database management system on a PC-type computer, The data are plotted as maps using the MapInfo geographic information system (GIS) package. Thresholds separating anomalous values from background values are determined using the PROBPLOT uni-variant statistical package, which enables the discrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to develop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.

Jan 1, 1995

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By J. F. Lupo

Heap and valley leach operations rely on solution collection piping placed within the heap to enhance both solution recovery and to assist overall solution management. The most common piping used in leaching operations is solid or perforated High Density Polyethylene (HDPE) pipe and Corrugated Polyethylene pipe (CPE). These pipes are widely used because of their low cost, ease of installation, durability, and flexibility. The typical recommended maximum design depth of burial for HDPE and CPE pipes is on the order of 30 meters (100 feet). However, ore heap heights at many facilities exceed 30 meters and some are now approaching 180 meters (600 feet) in height. At very high ore heap heights, the stability and performance of HDPE and CPE pipes becomes a critical issue for leaching facility design and operation. Failure of solution collection piping can lead to poor solution recovery, high hydraulic heads on the liner system, and in some cases, unstable ore slopes due to high solution pressures near slopes. This paper presents a review of methods that have traditionally been used to evaluate pipe stability under high normal loads. A common shortcoming of these methods is the inability to account for beneficial effects of ore arching around pipes and the time-dependent creep (stress relief) behavior of polyethylene (PE) materials. A new analytical approach is developed and presented which includes the effects of ore arching around pipes and creep of PE materials. The results of the new approach show that PE pipes will deform under high heap loads, but can remain stable and functional. Pipe stability is shown to be dependent on the type of pipe backfill and initial backfill compaction. The new approach represents a useful tool for designing applications for PE pipe under high normal loads.

Jan 1, 2001

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By Edgar Peña

La efectividad de un equipo en la planta de la industria minera es importante en tanto se opere con eficiencia y efectividad. Empero, es necesario conocer el método de cálculo que se ha empleado para determinar la tasa de efectividad del equipo y sobre qué datos se han hecho los cálculos. En esta perspectiva, el presente trabajo describe las herramientas utilizadas en Southern Perú Cooper Corporation para el logro de la calidad de trabajo a través del incremento de la productividad y control de los costos. Para ello, se han utilizado herramientas como: la recolección de datos, visualización de datos, diagramas de Pareto y análisis de beneficios. Asimismo, para una óptima efectividad del equipo deben mantenerse registros precisos de la operación del equipo.

Sep 13, 2001

By Tony Szwilski

Indonesia has enormous mineral resources. Its population of more than 180 million people inhabit most of the more than 13,000 islands. The country is becoming a significant economic power in Southeast Asia. Indonesia is the largest Muslim country in the world. Java, its largest island, is the most densely populated area. The country's diversity is its strength. However, as only an estimated 16 million inhabitants speak bahasa Indonesia as the first language, communication problems endure. Although burdened with large debts, Indonesia has been able to service the debts better than most developing nations. This has given it high credibility and, with increasing frequency, creditor nations compete to provide Indonesia loans with the most the most favorable financial terms. Recent rising prices of petroleum crude has further improved Indonesia's economic status. It maintains a policy of stable oil prices that it promotes in OPEC, of which it is an influential member. As a result, Indonesia is becoming increasingly attractive to foreign investors. The South East Consortium for International Development (SECID) is made up of 34 universities in the southeastern US and Indonesian partners Lembaga Afiliasi Penelitian dan Industri (LAPI) of the Institute of Technology in Bandung, West Java. SECID bid successfully against international competition to develop new academic programs and campus for the Sriwijaya University UNSRI) in Palembang, South Sumara. Funding for the project was provided by the government of Indonesia through a loan from the Asian Development Bank (ADB). There are 47 public universities

Jan 1, 1991

By Y. -J. Park, K. -H. You, Y. -T. Choi, Lee. H. -W.

Many large caverns are being constructed in great depths in Korea mainly for the storage of oil and LPG. These caverns are mostly located near the port where rock conditions are reasonably good. In some instances, the horizontal stress is very high and endangers the stability of the cavern. The purpose of this study is to assess the stability of large caverns excavated in a rock mass with high horizontal stress where Ko value is close to 3. Result shows that stress exerted in the shotcrete at crown exceeds allowable value when the 3rd bench is excavated. Also found is the tensile failure of shotcrete near the boundaries between benches. In Korea werden viele grosse Kaverne fuer Aufbewahrung vom Oel und Fluessiggas in grosser Tiefe gebaut. Am Meisten befinden sich diese Kaverne in der Naehe von Haefen, wo der Fels gute Verhaeltnisse zum Bauen einer Kaverne besitzt. In einigen Faellen ist die Horizontalspannung sehr gross und dadurch wird die Stabilitaet vom Kaverne gefaerdet. Der Zweck dieser Arbeit ist die Stabilitaet des im Fels gebauten grossen Kavernes mit hoher Horiaontalspannung zu schuetzen, wo Ko-Wert sich auf 3 naehrt. Die Ergebnisse zeigen, dass die Spannung im Spritzbeton an der Krone den zulaessigen Wert ueberschreitet, wenn das dritte Bank ausgegraben wird. Im Bereich des Spritzbetons zwischen Baenke wurde das Zugversagen festgestellt. Des larges cavités nombreuses sont en train d’être construites en grand profondeur en Corée prin-cipalement pour le stocage du pétrole et LPG. Ces cavités sont pour la plupart situées près de la porte oú les conditions des roches sont résonablement bons. En quelques cas, la contrainte hori-zontale est trés haute et met en danger la stabilité de la cavité. L’objet de cet étude est d’estimer la stabilité des large cavités excavées dans une masse de roche ayant une haute contrainte horizontale oú la valeur de Ko est proche à 3. Le résultat montre que la contrainte exercée dans le shotcrete à la couronne dépasse la valeur admissible quand le troisième banc est excavé. En plus une faillite en tension du shotcrete près de la frontière entre des bancs est trouvée.

Jan 1, 2003

By B. M. Das

Several laboratory model test results for the determination of the ultimate uplift capacity of single and group metal piles embedded in near-saturated clay have been presented. Based on the uplift test results for single piles, the variation of the adhesion factor with the undrained shear strength of clay has been determined, and an empirical correlation for estimation of the adhesion factor in soft and medium clays has been presented. The group efficiency of piles under uplifting load depends on factors such as embedment ratio, undrained shear strength of clay, the number of piles in a group, and the center-to-center spacing of the piles.

Jan 1, 2010

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By M E. Taulis, S Hayton, D A. Manhire, J G. Pope

Successful development of coal seam gas (CSG) resources in low-rank coalfields such as the Powder River Basin has raised interest in CSG from low rank coal in New Zealand. Kenham Holdings Limited holds 12 Petroleum Exploration Permits (PEP) covering some of New ZealandÆs low-rank coal and lignite resources and has engaged CRL Energy Limited to assist in the systematic evaluation of the CSG potential of the permits. To date, exploration results from seven New Zealand coalfields reflect differences in coal type, rank, depositional environment and depth of burial between coalfields. Several of the explored coalfields are considered prospective for CSG. One of the most advanced Kenham exploration programmes is in the Hawkdun Coalfield, Central Otago.   The Hawkdun Coalfield contains a single, thick lignite seam with properties that are similar to the Powder River Basin. Preliminary results indicate the Hawkdun Coalfield is prospective for CSG with the potential to contain between 25 and 60 PJ of gas; enough to supply a 30MW power station for ten to 25 years. Further drilling is planned to investigate the economic viability of the Hawkdun Coalfield. The in situ permeability of the lignite, the amount and availability of free gas, gas saturation at depth and market opportunities will determine its economic viability. If initial pumping and production results in the planned exploration programme are promising, the Hawkdun Coalfield will be further developed with additional production drillholes to form a trial production pod.

Jan 1, 2004

By P. J. Bhonde, R. D. Angal, R. H. Tupkary

Manganese imparts numerous beneficial mechanical properties. Hence it finds extensive application in iron, steel and non-ferrous sector. Prevalently, it is incorporated in the form of master alloys i.e. 'ferromanganese'. In India, ferromanganese is mainly the inexpensive and paramount source of availability of manganese. Various conventional and non-conventional techniques of ferromanganese production have been adopted in past and present. However, these techniques have demerits viz. high refractory, energy consumption, losses of valuables in slag and fumes. Also geographical co-ordinates of the plant restricted the manufacturer to prefer an appropriate process. Accordingly, the industrially implemented methods had reliance on availability of infrastructure, energy, mineral resources, grade of raw material, outlay of labor, environmental compatibility of technique etc. In view of the liberalized economy and the gap scenario in the supply and demand of ferromanganese, the authors felt it indispensable to explicitly bridge up this vacuum by initially designing a simple energy conserving, eco-friendly, low capital investment technique for decarburization of ferromanganese. Measurement of the data involved studying the impact of rate governing parameters on the process kinetics. This laboratory scale investigation is expected to escalate the Mn/C quotient of high carbon ferromanganese. Key Words: ferromanganese, carbon, carbide, decarburization, rate, kinetic

Jan 1, 2007

A mining engineer from South Africa, whose research has taken him to some of the world?s deepest gold mines, is the winner of the St Andrews Prize. Daniel Limpitlaw, 27, picked up a cheque for $25,000 for his dissertation on reversing the damage done by early mining technology, which he claims is partly responsible for blighting the urban environment in many South African cities. Launched in October 1998 by the University of St Andrews and international energy company Conoco, the St Andrews Prize sought practical solutions to environmental problems. It attracted interest from 450 individuals and groups from countries as diverse as China, Pakistan, Canada, New Zealand, Germany, the UK and the United States.

Jan 1, 1999