Search Documents

By Qing Wang

In this method the state of an open-pit mine is represented by the number of benches that are mined in each predesigned mining phase (or pushback). Consequently, a specific mining schedule can be represented by a sequence of states which starts with the topography of the mine site and ends with the ultimate pit. For a given set of mining phases all feasible states are first generated and sequences of states are then evaluated for technical and economical feasibility. The best sequence, which gives the maximum net present value (NPV), is found by applying a dynamic programming optimisation algorithm. The algorithm also optimises the cut-off grade which satisfies the mill feed requirement for each planning period. It was found that the algorithm can be used not only for scheduling but also as an effective tool for analysing the effects of mining and milling capacities and cut-off constraints on the mining schedule and the total NPV. The algorithm, which was programmed in C, was successfully applied to a large Au-Cu deposit

Jul 1, 1996

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By P. H. Davenport, L. W. Nolan

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Geochemical mapping provides a direct approach to delineating areas of epigenetic mineralisation and for relating the regional distribution of this mineralisation to an overall tectonostratigraphic and structural framework, as well as to extensive areas of hydrothermal alteration. Organic lake sediment is a widely available and effective sampling medium for regional geochemical mapping in Newfoundland, that has proved to be valuable in Au, Sb and W exploration

Jul 1, 1991

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By R. A. Lord, H. M. Prichard

efficiency is discussed from both experimental and

Apr 1, 1994

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By N. B. J. Kieser

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. Platinum-group minerals (PGM) in the enriched zone at Dust Mountain occur in two separate parageneses, the first representing primary magmatic PGM and the second primary magmatic PGM that have been reduced to alloys during serpentinisation. Minerals in the first group were unaffected by hydrothermal alteration on account of their textural setting or stable chemical composition. Despite substantial alteration of the serpentinised assemblage, most evidence points to the dominant role of primary magmatic processes in determining PGM occurrence. Several base metals have nevertheless been introduced hydrothermally. With respect to surficial dispersion the single most important paragenetic factor was the reduction of sulphides to alloys, rendering them more susceptible to mechanical erosion and less so to chemical leaching. The different textural setting of Pd-group and Ir-group phases results in different dispersion characteristics, with major implications for stream sediment sampling

Apr 1, 1994

By J. S. Mason

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Detailed paragenetic studies of the post-tectonic fracture-hosted vein mineralisation have demonstrated a complex paragenesis, reflecting a multi-phase combination of regional metallogenesis and tectonics through time. Previously published work regarding paragenesis and zoning was oversimplified. Two major epochs of mineralisation resulted in the emplacement of the A1 group of assemblages, from which lead, copper and silver were the main metals mined, and the A2 group, whose galena is only moderately argentiferous but which were major sources of lead and zinc. Tectonic and tentative isotopic evidence points to post-orogenic relaxation as the mechanism for development of the A1 assemblages in the early Devonian, whereas the A2 assemblages are believed to reflect Variscan extensional regimes and regional metallogenesis in the early Carboniferous and Permian

Jun 19, 1905

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905

By J Kokado, N Hatta, S Yabushita

A theoretical model is described for prediction of the capacity of fines from porous ores, such as cokes and sintered ores, to be removed by a pneumatic, horizontal-type classifier prior to charging into a blast furnace. First, the influence of variation in the apparent density and drag coefficient of porous ores on removal efficiency is analysed from a stochastic standpoint. The effect on efficiency of collisions between particles in the classifying region is then examined analytically in relation to the ratio of the mass flow rates of particles and air (the loading ratio). Finally, a theoretical model is constructed that takes these factors into account. Theoretical and experimental results are compared and classifying efficiency is discussed from both experimental and theoretical viewpoints.

Dec 1, 1993

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

By S. C. Tennant, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Immobile-element lithogeochemistry is providing a detailed chemostratigraphy of the submarine Ordo-Silurian volcano-sedimentary sequence. Primary lithologies and magmatic affinities of the sericitised and silicified volcanics are determined from binary plots of Nb, Zr, Y, TiO2 and Al2O3, while mass-change calculations using immobile-element anchors can identify and quantify zones of significant hydrothermal alteration. Stratiform polymetallic mineralisation at the western margin of Parys Mountain, around the Penymynydd fault zone, has been shown to have a distinct hanging-wall and footwall stratigraphy. These ore zones are probably part of a homoclinal, north-younging volcano-sedimentary sequence. The apparent stratigraphic complexity results from primary lithofacies variations and pervasive alteration, with the modifying role of the Caledonian orogeny much less than previously suggested

Jun 19, 1905

By R. A. Lord, H. M. Prichard

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The complex exemplifies a class of olivine-rich, platiniferous ophiolite complexes generated by unusually high degrees of hydrous melting above a subduction zone. Crystallisation of abundant olivine from unusually picritic magmas produced an exceptionally thick sequence of crustal dunite cumulates. Significant (1-4 ppm) concentrations of Pt+Pd occur where sulphide-bearing dunites are spatially associated with podiform chromite concentrations. In the area north of the Balta Sound, the chromitites appear to lie in distinct stratigraphic zones. A detailed programme of lithogeochemical and soil-rock interface geochemical exploration led to the intersection by diamond drilling of three stratiform horizons of sulphide-bearing dunites and associated precious-metal mineralisation. Patterns of cryptic geochemical layering, at scales from 200 m to less than 1 cm, suggests open-system fractionation

Jun 19, 1905

By B. M. England, L. C. Mackey

Magnesia minerals are included in most iron ore sinter mixes to provide the MgO requirements of blast furnace slag. The properties of these minerals have an influence on the eventual sintering properties of the mixes. A detailed study was undertaken of serpentine and dolomite and the use of limestone, olivine and magnesite was also investigated. A consideration of particle properties indicated that as these materials calcine a reduction in size can occur together with cracking and changes in surface properties. These changes could affect the permeability of the sintering bed and sintering performance. Studies of sintering reactions showed that magnesium and calcium, formed from the calcination of dolomite, are extremely mobile before the formation of melt. Evidence suggests that the movement of these oxides into surrounding areas is via a solid-state diffusion process. The diffusion of Ca into the surrounding hematite particles is faster than that of Mg, resulting in the formation of dicalcium ferrite and magnetite or magnesioferrite, the last two subsequently being converted to dicalcium ferrite in the presence of Ca with removal of Mg from the structure as ferroan periclase. Studies of pilot-plant sinters indicated that reaction mechanisms formulated from the bench-scale studies were occurring in actual sintering processes. The differences in sintering reactions between dolomite and serpentine were considered to be the major cause of differences in the availability of lime for bonding phase formation. Pilot-scale studies indicated that the sintering properties of a mix containing dolomite could be improved by increasing the basicity of the sinter mix while keeping the MgO level constant

Jun 18, 1905