Search Documents

By D. E. Macdonald

"Approximately 2.0 million tonnes of phosphate rock is imported from the U.S. to Alberta annually and is used in the production of agricultural fertilizers. No phosphate rock is presently mined in Canada, although sources of igneous phosphate have been mined in the past. Sedimentary phosphate rock is found in nine geological units within the Cordilleran Foothills and Front Ranges region of Alberta. The Devonian-Mississippian Exshaw Formation, Permo-Pennsylvanian Rocky Mountain Supergroup, and the Jurassic Fernie Formation have the best potential f or future development. Most of the phosphate rock in Alberta is of low grade and lies within restricted land use areas. The best over-all resource potential lies in the Fernie basin area of southeastern British Columbia, in the Fernie Formation. The possibility of deep phosphate rock deposits in the plains region should be examined.Phosphate rock is mined in Idaho, Utah, Montana and Florida, and is shipped to Canadian fertilizer plants for processing. Raw phosphate rock is acidified, usually with sulphuric acid, by a wet process. Varying amounts of ammonia are added, and the fertilizer is pelletized. Future research, in western Canada, is needed in the beneficiating of low-grade ores and in the area of in situ mining. At the present time, phosphate rock sells for around US$50Itonne, and Alberta fertilizer companies probably pay in the range of C$7D-$85Itonne for U.S. phosphate rock delivered to the plant. Environmental concerns about phosphate rock processing are centred around gypsum tailing ponds, and radioactive wastes.U.S. supplies of phosphate rock are secure until the year 2000; however, by this time, the richer deposits in the U.S. may be exhausted. Alternate deposits, such as the ones in Alberta and British Columbia, might then be considered. Phosphate byproducts, such as uranium, vanadium, fluorine and rare earth elements, may help in making the processing of low-grade Canadian phosphates economically feasible."

Jan 1, 1988

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

By David van Cleave, David L. Rome

Whether you buy your minicomputer from a manufacturer or another vendor, the first thing you must do is define your needs. With good planning, the initial cost will be low and your return on investment will be maximized over the long term. Involving all members of your staff who will he using the new computer in the planning phase is also important. Their participation will alleviate any potential concerns they may have about new equipment, and their suggestions will provide valuable input for your specifications. After you define your proposed system, survey available hardware and software. The survey will help you in the next step, preparation of specifications. The specifications, along with a quote request, are then sent to various manufacturers. Consider the Manufacturer When selecting your minicomputer, one important item to consider is the manufacturer. Remember, when you buy a computer, you're also buying the services of a computer company. A firm that makes a commitment to its customers and provides a product that is field tested before releasing it for sale is preferable. Examine the company's maintenance and support packages, since every machine requires preventive maintenance. Does your manufacturer or original equipment manufacturer (OEM) support service sites in your area? Has their service record been commendable? Will they provide training for your personnel and a supply of circuit boards so you can retain a degree of self-service autonomy? Three methods of buying a computer involve the manufacturer, an OEM, and the systems house. Buying direct from the manufacturer means you go straight to the source, using no middleman. This gives you maximum flexibility; you can consider every alternative and many possible combinations of computers, peripherals, and software until you find exactly the right system for you. The OEM buys computers direct from the manufacturer and builds them into his own computerized, special purpose product. He usually sells a complete package, including software and hardware, and often noncompetitive equipment as well (a scientific or engineering instrument, for example), designed for the mining market. Because he offers a packaged product, the OEM can often charge less for the system than if you put the pieces together yourself. In many ways, the OEM also provides a unique system. And while the OEM sells a packaged solution, he also usually has the special market knowledge necessary to modify the system to meet your unique needs, if necessary.

Jan 11, 1981

By P. Rooney

In due course, new smelters will have to be installed in order to meet the increasing worldwide demand for copper. This paper presents the results of a study made for the purpose of identifying the most desirable countries in the world in which to locate a new smelter. Both sociopolitical and economic factors were taken into account. Criteria developed and methods used to assess each possible location are described. The study indicated that the most interesting potential locations are Canada, -Chile, Portugal and the USA for new copper smelting complexes.

Jan 1, 1983

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco's Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

In 1984/85 financial year Australia produced 529 thousand barrels per day (kbd) of crude oil. By far the major contribution (453 kbd) was light waxy oil from offshore Gippsland, Victoria. When these discoveries were made in the latter 1960s, imported oil was available in abundant supply and at low prices. Because of this, the Gippsland producers persuaded Government to control the marketing and pricing of their crude, and thus provide the required security of offtake. Political events in the middle East created supply shortages during the 1970s, and dragged up government selling prices for OPEC crude oil. Thus Arab Light crude that sold for less than US$2/barrel (bl) in 1970 reached $34/bl in 1981. Following the consequent decline in world oil demand, in 1982, Australian refiners sought to evade their obligation to lift Gippsland crude. Hence, in 1983, the Government was forced to introduce a floor quota of 385 kbd of Gippsland crude liftings and to allow producers to export any additional production refiners did not require. On expiry of the old arrangements, Government introduced a partial free market from January 1985, whereby the balance in excess of 350 kbd may be sold to Australian refiners at negotiated prices, or exported as before. In 1984/85 exports were some 90 kbd and will be higher in the current year. About half this total has been exported by BHP, providing valuable experience and lessons which are described in the paper.

Jan 1, 1986

By Thomas D. Kaufmann

Whether pursuing hedging or speculative strategies, gold miners can increase sales revenues 1 % to 6% by constantly pricing production forward. Unlike other commodities, gold futures prices are consistently higher than spot prices. A Colorado School of Mines study showed theoretically and empirically that in the 15 years since the price of gold was released from government control, the forward price for gold has been higher than the current price almost 100% of the time. The reason why Metal traders know that holders of metal earn a bonus selling forward when the metal is in "contango." "Contango" is a mysterious word that crept into the trading vocabulary a century ago. It designates a situation when the price of a metal on the futures markets is higher than the price in the immediate or spot market. If the spectrum of spot and futures prices remains static over time, the forward seller who has contracted at a higher than spot price can make a profit equal to the contango by redeeming his commitment at the lower spot price when the contract matures. Consequently, when a seller in a contango market hedges, he makes a profit on the transaction in addition to avoiding a price change risk. On the other hand, buyers of the metal who hedge in a contango situation will sustain a loss equal to the contango. Producers of gold, however, are sellers of gold. For most metals and oil, there is no inherent reason why futures prices should be higher than present prices. Buyers and sellers decide that the price of the commodity will be lower or higher than present values for a variety of reasons.

Jan 1, 1991

By Juan Patricio Ibáñez

Separation of arsenic and copper from Cu-As-H2S04 electrolytes by electrodialysis has been investigated at room temperature. The effects of current density and pH were studied. An arsenic-free copper solution was obtained for all the tested conditions. The transport efficiency for copper ions was found to be higher than 98% after 3 hours' test. Transport of arsenic and copper through the ion exchange membranes was increased by increasing pH and current density. Solution pH was found to be a key parameter for the separation process, since it controls the speciation of the ions to be transported and the formation of unwanted precipitates which reduce the global efficiency of the electrodialysis process. The main conclusion is that electrodialysis is a promising technique to be used in separating and/or concentrating ions of interest in copper electrometallurgy.

Jan 1, 2003

By K. R. Robilliard

Ausmelt Technology has been developed to process copper concentrates containing significant levels of lead, arsenic and antimony. A process was developed aimed at smelting these concentrate materials to remove the contaminants to fume and produce a clean copper product. The production of clean copper and the potential economic benefits of this process step over the sale of impure concentrates is discussed.

Jan 1, 1995

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

By Stephan Jefferis

It is my understanding that the Scandinavians have done some fundamental work on durability. I have seen a study published whereby the author, Helen Anderson, comments on the durability of polyurethane grouts and there was -if I am not mistaken- a reference made to another Scandinavian testing institute comparing durability of the polyurethane to cement grout under the same type of circumstances. Circumstances are important so we should actually ask the gentleman to shed some light on this particular method because apparently Scandinavia is the place where durability has been taken very seriously and has been well researched.

Feb 10, 2003

By S O. Hille

Modern remote mining operations in Australia are more commonly trending towards fly-in/fly-out (FIFO) sites. This trend is driven by numerous factors including increased business centralisation, reduction in operating costs, and a desire to live in coastal cities that offer closer family networks and a greater diversity of facilities. Consequently, the resource development industry has had to adapt. When WMCÆs Mount Keith Nickel Operation commenced operations in 1994, it was developed as FIFO for its entire workforce. Since then, there have been several permutations of rosters within a 21 day compressed work cycle including the 14/7 cycle. This paper discusses a case study of the change in management process to the 9/5 work cycle focusing on minimising fatigue in the workplace. It includes the discussion of the business case, employee reaction and the practical application. The impact of the best practice change after 18 months is discussed.

Jan 1, 2002

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By AIME AIME

THE second session on geophysical prospecting at the February meeting of the Institute was a discussion of the mining law and the bearing of the new method of search on location of claims and assessment work thereon. Allen H. Rogers was chairman of the meeting, which he opened by reviewing the present law and the proposed changes. W. R. Ingalls commented (by letter) on the Arentz bill, as introduced into the House of Representatives in 1921 and the need for revision of the present mining law. L. W. Douglas explained (by letter) the bill that he introduced and which has been passed by the House. SAMUEL S. ARENTZ, Nevada: It is my opinion that if the American Institute of Mining and Metallurgical Engineers is to sell this proposition to the people in the West, they have to sell it to the lawyers, because, after all, they are heard loudly when it comes to speaking in Congress. One man tells the other, "This thing is a vicious piece of legislation"; it might not be, but they will pass it on if it affects them. If the Institute would impress on the people affected that we need a re-codification of the mining law and that such is necessary along certain lines; that things have changed during the past decade or two, so today instead of doing our prospecting alone through the sinking of a shaft, through a discovery that may be seen, we are now moving on to more modern means of discovery through geophysics, through the churn-drill, through geology, through geological inference, I think we could get somewhere.

Jan 1, 1929

By John R. Bogert

The title of this session is "Wall Street Looks at the Mining Industry," and I am going to attempt to answer the question: Shouldn't Mining Stocks Sell at Higher Price Levels? Or, What Does Wall Street See When Looking at the Mining Industry? Well, it sees a capital intensive business, a technical industry, and a growing industry becoming more vertically integrated. But, at the same time, Wall Street sees a cyclical industry, a fragmented industry of erratic earnings, spotty public relations, a feast-or-famine business where the public usually does not differentiate between coal mining or metal mining, and does not appreciate either the risks or the rewards. As a result, mining stocks generally sell at relatively low price learnings ratios in comparison to other industrial groups. This PIE ratio, the current market price of the capital stock divided by annual earnings per share, is probably the most popular index of a stock's value. The average of the price/ earnings ratios of the 30 stocks comprising the Dow Jones Industrial Average is over 14. This diverse group of stocks is widely regarded as being a cross-section and representative of the industrial companies listed on the New York Stock Exchange. However, in comparison to 14, Asarco and Kennecott shares are currently available for about 8 times annual earnings. Even discounting earnings from South America, the stock of these two companies sells at only 10 times earnings. Of course, Peruvian politics is currently preventing Cerro shares from selling above 6 times earnings, and Chilean politics keeps Anaconda shares at a PIE multiple of 7. However, even in better times, these companies rarely sell above 10 times earnings. American Metal Climax and Newmont sell at only 11 times earnings as does Phelps Dodge and St. Joseph Lead. Few mining companies then have what can be considered a high PIE ratio-a figure higher than

Jan 1, 1970