Search Documents

By R. S. Nutter

The results of designing, constructing, and laboratory testing of a modular, distributed, microprocessor-based mine monitoring and control system are presented. A standard computer communications protocol (DDCMP) was utilized throughout the system. Tests were performed on the utilization of a high-level language for programming mine monitoring and control systems. Laboratory tests were run on a combined air velocity/methane sensor.

Jan 1, 1980

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state regulatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

A compilation of papers presented at the Fifth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on July 30, 31, and August 1, 1980. Papers cover areas of electromagnetics/power systems, power systems, monitoring and control, and communications.

Jan 1, 1980

By Shelby Z. Palya

"INTRODUCTION The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publicatioll3 and articles, from January 1, 1960, to December 31, 1964,4 from January 1, 1965, to December 31, 1969,5 and from January 1, 1970, to December 31, 1974; 6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1975,7 from January 1 to December 31, 1976,8 from January 1 to December 31, 1977,9 and from January 1 to December 31, 1978.10"

Jan 1, 1980

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 1, 1980

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By R. E. Robinson

I shall present a concept for the development of the resources of this country and its neighbours that repre¬sents a fantastic challenge to our scientists and entre¬preneurs. This concept offers prospects of development that must make our previous achievements seem equivalent only to the first act in a drama enacted on the stage of Southern Africa. I hope to illustrate how, in Act Two, chemistry will play a dominant role, and chemists and chemical engineers will be among the principal actors.

Jan 1, 1980

By James R. Wait

The present final report constitutes the total productivity of a series of contracts from the U.S. Bureau of Mines and the Institute for Telecommunication Sciences over the period 1971-1979. The emphasis on the research has been analytical. In this "executive summary" we give a succinct description of each phase of the investigation. In the first phase of the investigation that was stimulated by the National Academy of Engineering, we concentrated on the analytical studies of techniques relevant to mine rescue. Several specific procedures for locating a buried source were analyzed. In the next, but overlapping phase of the investigation, we dealt with the fundemental character of how electromagnetic waves propagate in mine tunnels. At the outset we allowed for the finite conductivity of the tunnel walls and the presence of axial conductors such as cables, pipes, and tracks. The third phase of the investigation was devoted to the analyses of various specific geophysical engineering problems. The related fourth phase dealt with the general subject of non-destructive testing of wire ropes such as used for mine hoists.

Jan 1, 1980

By Joseph G. Wargo

A meteoric rise in selling price has revived gold exploration activity throughout the world. In the United States the effort is, in large measure, channeled toward discovery of disseminated gold deposits such as the Carlin-type, i.e., with size and grade characteristics similar to Newmont's Carlin mine in Nevada. The subtle surface indications characteristic of Carlin-type gold mineralization have been examined by a number of geologists, and the more obvious prospects have been tested by surface sampling and drilling. It is likely that most of these readily recognizable deposits have already been found and, as a consequence, prospectors are now entering a new, second stage of exploration for Carlin-type and related disseminated gold deposits.

Jan 9, 1979

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979

By P. S. Martin, B. J. Guarnera

As an energy source, lignite is short on selling points-it contains large amounts of moisture and often large amounts of ash, resulting in low heat content. The moisture produces rapid oxidation upon exposure and self-ignition commonly occurs within two to three weeks, resulting in major transportation and storage problems. Nevertheless, as interest in alternate fuel sources increases, lignite deposits in the Coastal Plain of the US are attracting more and more attention. Two lignite mines are operating in Texas and additional developments are planned in that state, Arkansas, and Louisiana. At present, Texas lignite is burned only at mine-mouth generating facilities, but more exotic uses such as gasification are projected in the future.

Jan 4, 1979

By Jerry G. Rose, Robert C. Howell

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14 000 kPa (2000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room and-pillar mines so that a substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction became of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal- crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 3, 1979

By John D. Wiebmer

First, a definition of a small scale miner is in order. The US Bureau of Mines classifies him as one who produces 360 t/d (400 stpd) of ore or less. In Canada, he would be refered to as a "junior company." Mexico identifies the small scale miner as one whose gross income from operations is less than $880,000 per year. A small surface mine in India employs less than 400 people, and a small underground mine employs less than 150. Peru considers a small scale miner one who produces less than 54 000 t/y (60,000 stpy) of ore. Obviously, the term is relative. What may be a small mine in one country is a medium or large mine in another. This lack of agreement is understandable since small scale mining does not often cross national boundaries. Rather, its effects are felt at the regional and local levels within each nation. Its importance doesn't lie with any huge contribution to the GNP or balance of trade. Instead, its value is as a local employer and as a frontrunner in geologic exploration.

Jan 2, 1979

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By J. R. Beeder

Minerals Engineering Company (MECO) is a relatively small, promotionally oriented mineral exploration company founded in Colorado in 1948 during the height of the uranium boom. The company has been: 1. in uranium exploration and production 2. a drilling company 3. a manufacturer of Geiger counters 4. a major tungsten producer 5. then dormat for several years and 6. now we are back into exploration on a broad scale. We have been in underground lead and zinc production in the 1970's but we are now involved primarily in "wheeling and dealing" in mineral exploration. The company has had diverse interests in the past and we are presently diversifying to some extent into oil and gas ventures.

Jan 1, 1979

Computerized financial models can be used in all phases of the mineral industry from setting exploration targets to projecting profit plans for producing mines. In this presentation, I will use the example of an exploration company entering a new district to trace the application of financial models through the following intermediate phases. 1. Hypothetical analysis and strategy 2. First encounter of mineralization 3. Preliminary drill results - decision process 4. Feasibility studies 5. Post-feasibility negotiations 6. Producing mine 7. Acquisition of producing mines or mineral properties. I will conclude with a brief discussion of the mechanics of the financial models that we use at Wright Engineers Limited. As we progress through the seven phases, the availability and accuracy of the data will parallel the complexity and application of the financial models. However, the same basic financial models are utilized throughout the seven phases. I will begin by suggesting that the exploration group is somewhat autonomous and has the mandate to explore in Western Canada.

Jan 1, 1979