Search Documents

By M. Bleeck

Calcium carbonate (CaCO3) is one of the most ubiquitous and versatile minerals found in the earth's crust. Its availability, attractive physical properties and relatively low processing cost make CaCO3 the most widely used filler material today. It is mined in three different forms - chalk, limestone and marble. Each physical form of CaCO3 has different qualities due to differences in postdepositional geology. But the chemical composition remains the same, with CaCO3 an inert component of the finished product. In the past, the paper industry largely left CaCO3 by the wayside, as it cannot withstand the acid-based papermaking process. But conversion to an alkaline system by many US mills changed this picture. Carbonate suppliers have put time and effort into research and development, demolishing barriers and creating new possibilities for what is a simple, natural product. By controlling particle size, size distribution and particle charge, the industry uses ground calcium carbonate (GCC) as a performance enhancer and as an extender for more expensive ingredients. It is estimated that the United States uses 3.6 to 4.1 Mt/a (4 to 4.5 million stpy) of CaCO3. Consolidations and mergers are taking place in the industry. Of the 12 major GCC producers in operation nine years ago, seven are left. Mineral Technology (US) is the dominant precipitated calcium carbonate (PCC) producer with more than 50 satellite plants worldwide. Other producers include Georgia Marble (French); Franklin Industries (US); OMYA (Swiss); J.M. Huber (US); ECC (English); and Filler Products (US). Global Stone PenRoc (Canada) is the only newcomer. In addition to this group, there are three small producers left in North America, each with a capacity of less than 100 kt/ a (.110,000 stpy). The trade organization operating as the Pulverized Limestone Division of the National Stone Association renamed itself the Pulverized Mineral Division, to increase its membership pool. The US paper industry is a predominant GCC con¬sumer, using approximately 800 kt/a (882,000 stpy) at an approximate cost of $130/t ($1.43/st). European paper mills pioneered alkaline papermaking. In the early 1960s, they began using GCC as filler and soon thereafter added GCC to their coating formulations. A decade later, the North American paper industry followed suit. The conversion from acid to alkaline paper production benefits the economic and performance aspects of the industry. Less pulp is needed, paper machine maintenance and effluent treatment costs are reduced, and sheet strength, opacity and brightness are increased. Perhaps most important to the reader, the sheet is desensitized to ultraviolet light, extending the paper's archival ability. CaCO3 can provide the papermaker with additional control of his paper. For example, PCC has long supplied the tobacco industry with a means to slow down the burning rate of cigarettes. Due to enhanced performance with regard to bulk and opacity, filler PCC use has risen to 1,500 kt/a (1,650 stpy) in the United States, at an approximate price of $130/t ($143/st). The majority is produced onsite at the paper mill, using "satellite plants." This concept reduces freight cost because only quicklime (CaO) is shipped to the mill, not CaCO3 slurry. The future of CaCO3 is encouraging. The amount of natural ground CaCO3 used is expected to double by the year 2005 to approximately 8 Mt (8.8 million st) worldwide. Acid papermaking practices will feel an increasing pressure to convert to an alkaline process as larger volumes of GCC containing paper enter the recycling market. CaCO3 reserves are plentiful. They will supply the ever growing demand for increasingly sophisticated paper. The plastics industry is supplied with almost 900 kt/ a (990,000 stpy) GCC at an annual growth rate of 4% to 5%. The price of a functional, inorganic filler, surface modified for the plastics industry, has an average selling price of $220/t ($243/st). GCC represents the most common filler, creating a product with higher gloss, better dielectric properties, impact resistance, weatherability and shrinkage control. CaCO3-filled plastics surround us - auto hubcaps and dashboards, shower enclosures, floor tiles, wire coatings, microwave dishes and Tupperware. The caulking and sealant industry is an enormous GCC user, with annual consumption requiring 1.13 Mt (1.2 million st) at about $44/t ($48.50/ st). Caulking and sealant may be highly filled with GCC yet undergo no adverse flow effects, with a narrow particle-size-distribution filler decreasing the binder demand. The CaCO3 industry, as well as the carpet industry, are more or less tied to the growth rates of the construction industry. It is estimated that the carpet industry uses some 680 kt/a (750,000 stpy) of GCC at about $25/t ($27.50/st). The paint industry uses approximately 300 kt/a (331,000 stpy) at a 1 % to 1.5% annual growth rate. Here, too, GCC is the dominant filler. It is used to enhance flow characteristics and color uniformity. It also extends costly titanium dioxide, creates sheen and controls roughness, hardness and tack. More CaCO3 should be used in the future as industry shifts from solvent-free or water-based formulations that can accommodate higher GCC volumes. CaCO3 is not imported or exported in any great quantity. Most areas have reserves of their own and the selling price is relatively low. Even so, quality varies from deposit to deposit. As our needs become morespecific, it remains a challenge to provide varying industries with a fitting product.

Jan 1, 1998

By Robertson AC

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authors' personal observations and experience.

Jan 1, 1998

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By Amy Nelson

In the electrolytic production of zinc, cobalt is removed from the zinc electrolyte by cementation with zinc dust prior to electrowinning. Although the thermodynamics for this reaction are favourable, kinetic barriers to cobalt reduction render the method almost useless in practice unless activators such as copper and antimony or arsenic are added. There is a large body of work studying the effect of these additives, yet the mechanism by which they act is still poorly understood. Even when the target conditions are met, zinc dust consumption is excessively high: satisfactory operation requires up to 300 times the stoichiometric amount of zinc dust. The objective of this work is three-fold: (1) to examine the effects of activators and elucidate the characteristics that make a good activator; (2) to identify new additives that could lead to a more efficient purification process; and (3) to test the new additives with synthetic and real electrolyte solutions. The present paper gives a status report on this project.

Jan 1, 1998

By David Dreisinger

The cyanidation of copper containing gold ores results in the co-dissolution of copper along with gold. Copper dissolution results in elevated cyanide consumption that may make the treatment of the gold ore uneconomic. Copper-cyanide species in gold mill effluents may increase the environmental toxicity of the gold mill solutions. The objective of this study was to examine the use of solvent extraction to recover the copper cyanide species from gold mill effluents. Solvent extraction with Cognis (formerly Henkel) reagents LIX 79 and LIX 7950 was studied. Excellent extraction of copper and cyanide was achieved using pH control in extraction. Copper and cyanide may be stripped from the reagents using basic eluants. Various routes for copper and cyanide recovery from the strip solution were studied. Excellent results were obtained using electrowinning in both divided (Nation membrane) and undivided cells. Cyanide recovery was obtained by AVR treatment of a bleed stream from electrowinning. Full results of solvent extraction, copper and cyanide recovery are reported.

Jan 1, 1998

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By A. Dale Wunderlich

With the price of precious metals at an 18-year low, every ounce of metal produced is important. The theft of metals from mining and refining sites can mean the diffrence between profit and loss for many mining companies. Low metal prices do not reduce the potential for the theft of precious metals. History has shown that the price of gold has little to do with the desire for employees to steal precious or base metals. There is actually evidence that the theft of precious metals increases when the price of this commodity goes down. Several of the major precious metal thefts in the past year took place at silver mines when the price of silver was less than 16 cents/g ($5/oz). How does the lowest gold price in 18 years affect the need for security at precious metals properties? There is no short answer to this question. One reason is because the exposure to theft of precious metals is unique to each property. This makes it important that each property be evaluated individually. More than 95% of all precious metals thefts can be attributed to those working at the mine site. So preventing employee theft is the primary concern. One consideration is the location of the property. Gold selling at any price is still an attractive commodity in countries where the employees are making between US$400 and US$600 a month. It is not uncommon for employees at mines in countries where low wages are the norm to consider the value of a gram or two of gold to be a significant amount of money. A gram or two of gold a day may not seem like much. But if 15 employees steal two grams a day, that equates to a significant amount of money during a year. The type of property where the precious metals product is being recovered is also important. For example, a property with a gravity circuit is more likely to suffer from the theft of gold product than a property where all gold is finely disseminated and the only gold seen in the ore body is through a microscope. Gravity circuits increase an operation's exposure to theft because the grinding circuit that is associated with a gravity circuit often becomes a giant concentrator. Areas such as the bottom of grinding-mill pump boxes, cyclone-feed-pump clean out traps and the sumps often become locations where precious metals concentrate (Figs. 1 and 2). Muck concentrations in these locations can be as high as 25% to 40% of gold or silver. Not long ago, muck was removed from a barren-solution sump at a Merrill Crowe circuit that had concentrated to more than 40% gold. At a milling site in the Pacific Rim, residents of the community adjacent to the mine learned about the value of the concentrates in the sump under the ball mill and committed an armed rob¬bery. While several of their co-conspirators held the em¬ployees at bay with machetes, the others emptied the contents of the sump into buckets and removed it from the site. Armed robbery is not as common as employee theft. However, while this article was being written, an armed robbery occurred at a gold property in Central America. Armed perpetrators took as hostages the night shift employees at a process plant and used cutting torches that were on site to cut into the high-security and gold-storage areas. The perpetrators then stole a company vehicle to remove the stolen gold buttons and sludge from the site. Unfortunately, this type of activity goes on regularly. But managements of most mining companies are reluctant to discuss theft scenarios. So information pertaining to the theft of precious metals seldom becomes a newsworthy item. An audit conducted at a mine site with a gravity circuit recommended that the gravity recovery area be shut down until adequate protection could be provided. Although it was not connected with the audit, it was necessary to shut down the gravity area for a pro¬longed period because of problems with the gravity table. In the two months that followed, gold production at the site increased by about 31 kg/month (1,000 oz/month). It is difficult to attribute all of this increase to the theft of concentrates. But there was a good chance that at least part of the increase was due to the fact that concentrates were being stolen from the gravity area.

Jan 1, 1998

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By Rob Robertson

The problem of fine coal slimes has been addressed in a unique way at A. T. Massey Coal?Company. Several plants have employed two-stage classifying cyclones to separate the minus 1 mm raw coal into 3 sizes. Larger cyclones make the initial cut at approximately 150 µ (100?mesh) sending the underflow to a cleaning circuit (usually spirals) while the overflow is pumped to a secondary cyclone circuit using smaller cyclones. The small cyclones make a cut at near 70 µ (200 mesh) and produce an underflow that is a des limed flotation feed. The overflow is discarded to refuse due to its high ash and superfine size which would produce a high moisture product even if suitably recovered.

Jan 1, 1998

By William A. Faust

La Colorada Mine was begun in 1993 as a small heap leach mine and was the first operation for Eldorado Gold Corporation. 'This paper describes the growth of the mine to annual production levels near 60,000 ounces of gold and highlights recent improvements that were made to maintain a profitable operation by efficiency gains and cost containment programs.

Jan 1, 1998

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

A very wide range of technologies are utilised in the mining and processing of ores and a great deal of effort is expended in the development of ænew technologiesÆ to improve mining performance and economics. Traditionally, technology and people have been treated as separate aspects of an operation, when in fact they are inextricably linked. The successful implementation of new technologies is entirely dependent upon the actions, enthusiasm and skills of people, both as individuals and working in groups. This paper discusses the role of technology in mining and how new technologies are implemented by the industry. The paper argues that existing technologies have not been fully or adequately utilised and that effort should be re-focussed on the implementation of technologies that have been taken for granted for many years. The need for greater emphasis to be placed on the management of the human-technology interface is discussed.

Jan 1, 1998

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

By Pekka Hanniala

The Outokumpu Flash Smelting process today is the most feasible method for copper matte smelting. The economic feasibility of the process has always been one of the main decision making criteria in smelter projects. Thus, today about 50 % of the world primary copper production utilizes Outokumpu Flash Smelting Technology. However, in the future, environmental criteria will have stronger and stronger impact on decision making. Flash Smelting technology offers the best pollution control features of any process. today. It is foreseen that, in the near future, the global trend will be that all the smelters must decrease their emissions at an accelerating rate, compelling the smelters to make increasingly larger investments on environmental protection. In most of smelters ?today, Peirce-Smith converting and transfer of the molten material in ladles are the number one pollution source. The key today for copper converting and minimizing emissions is the Kennecott-Outokumpu Flash Converting process, which has proven to be the most effective converting method in terms of pollution control and, production efficiency including capital and operational costs. Outokumpu Flash Smelting technology is applicable also for small to medium scale smelters but the most interesting area is the upper capacity limit for smelting in one line, which has not yet been reached. We predict that by the year 2000 to 2005, there will be at least one smelter which produces 500,000 tonnes of Cu per year based on one Flash Smelting and Flash. Converting unit. The current state-of-the-art of the Outokumpu Flash Smelting - Flash Converting process is presented in this paper as well as some new options for copper production to be utilized in the near future but which are available already today.

Jan 1, 1998

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By I Levy

At our Monkland Mine at Gympie, we operate a deep, narrow vein gold mine using hand held equipment, rail mounted haulage and narrow shafts. This is in many respects the old-fashioned way and is well suited most of the orebody geometry exposed to-date. We have also commenced some long hole stoping and we use alimaks for some jobs. The heart of our particular mining style is the employment and retention of experienced miners with remuneration based on productivity. We do our planning/monitoring/supervision down to the level of daily individual productivity. In focussing on cycles per se, we have chosen not to talk about drill and blast cycles or cycles for mine development, stope preparation or drawdown and haulage. Instead we have stepped right back from the operation as presently run and have adopted a very broad view of the mining cycle. We will in this presentation intertwine the ebb and flow of, exploration, project sponsorship, development, production and cash returns to owners. The time line considered spans both history and predicted future.

Jan 1, 1998

Jan 1, 1998