Search Documents

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By T. Maejima, K. Aoki, T. Mori, K. Iwano

Concerning the excavation of rock cavern, it is one of the most important issues to evaluate the behavior of rock joints. But few detailed measurements for joint behavior had been conducted. Therefore, in order to evaluate the stability of rock cavern, effective approach for monitoring and analyzing the joint behavior needs to be developed. In this paper, authors described the results of analysis for joint behavior during the excavation by comparing with both results of the in-situ measurement by BTV and the numerical analysis by MBC model. Bei Ausschachten von Gesteinshöhlen ist es von besonderer Bedeutung, das stark von den Verbindungsteilen beeinflusste Gesteinsverhalten zu bewerten. Jedoch wurden bisher nur wenige Beobachtungen über das Öffnungsverhalten von Verbindungen durchgeführt. Daher muss ein effizientes Verfahren zur Überwachung der Stabilität unterirdischer Höhlen und der Analyse des Verhaltens von Verbindungsstellen entwickelt werden. In der vorliegenden Studie beschreiben die Autoren das Verhalten von Verbindungsstellen während der Ausschachtung durch Vergleiche sowohl mit den Ergebnissen von in situ Messungen mittels BTV als auch numerische Simulation mit dem MBC Modell, welches auch Diskontinuitäten berücksichtigen kann. Quand il s’agit d’excaver une caverne dans une roche ayant des joints très développés, il importe fort d’évaluer le comportement de la roche. Cependant, le nombre d’observations du comportement des roches effectuées au niveau de joints est loin d’être suffisant. Par conséquent, pour s’assurer de la stabilité des parois des cavernes souterraines, il a fallu mettre au point une méthode fiable de détection et d’analyse du mouvement des joints. Dans cet article, les auteurs décrivent leurs études de comportement des joints pendant l'excavation, en comparant les résultats des mesures effectuées in-situ, dans un chantier d’excavation par BTV , avec ceux d’analyse de la simulation numérique par MBC permettant de tenir compte des discontinuités.

Jan 1, 2003

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

By J. J. Forbes

Problems connected with the incidence, effects, determination, and control of dusts are still much before the public, although more information is available to the layman than when Bulletin 400, of which this publication is a revision,5 was issued in 1937. Bulletin 400 attempted to assemble information in convenient form on various phases of the dust problem, largely in the mining and allied industries. This revision includes data that have accumulated since 1937 and some that appeared previous thereto but were not available to the authors at that time. The literature on this subject is so voluminous that no attempt has been made to include all published material or all types of dust diseases, but only to assemble some of the more outstanding data on several aspects of the subject.

Jan 1, 1950

By E. H. Burroughs

This bulletin is the fifth in the series of petroleum bibliographies publis:\:l.ed by the Bure.au of Mines, Bulletins 149, 165, 180, and 189 being compilations for the years 1915, 1916, 1917, and 1918, respectively. In this bulletin the same general plan has been followed in arranging the references, but a few changes and additions have been made in the classification.

Jan 1, 1923

The oxidation of ferrous sulphate to ferric sulphate with air and oxygen in a gas lift percolator was investigated with initial Fe2+ concentrations in the range 0·01 M to 1·0 M,temperatures in the range 20-80°C, and pH in the range oto 2.The rate of formation of Fe3+ was found to be well described by the rate expressionEquation 1and a consistent mechanism is proposed.The presence of Cu2+ was found to cause an increased rate of oxidation, the effect being greater with Cu2+ concentrations increasing in the range 0·001 M - 0·01 M in 0·2 M Fe2+. The effect of other solutes containing Ni, Zn, Mn, Co, Hg, Cl, Mo, NH4, As, Cr, or Na at a concentration of 0·001 M in 0·2 M Fe2+ was negligible.

Jan 1, 1972

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

The Canadian mining industry is one of the strongest in the world. Not only does the country produce a sizable amount of minerals and metals, Canada plays host to hundreds of global mining companies, large and small. The country, for the most part, recognizes the importance of natural resource development, particularly mining, to its economic well being. Like any country, though, there are federal and provincial regulations on the books that the industry takes issue with. But there are also certain economic incentive programs in place to encourage exploration and mine investment. And, unlike the industry and the United States government, the Canadian government and mining industry appear to have a reasonable working relationship.

Jan 4, 2010

Demonstrate the technical feasibility of using nontraditional, low-rank, coal-based fuels and new coal-based technologies for mineral and metallurgical applications. Approach A cooperative research effort was initiated between the Bureau of Mines, U.S. Department of Energy and the minerals industry to extend the application of the fixed-bed gasification process to low-rank Western coals. The research effort enabled cooperators to gain operating experience in the use of hot, raw producer gas for iron ore pellet induration and other high-temperature mineral processes. Researchers were able to gather data regarding the fundamental engineering aspects of the fixed-bed process and gas cleanup for a wide range of solid fuel properties. Applying Fixed-Bed Gasification As a prerequisite to gathering the data needed for the study, the Bureau of Mines designed and installed, at one of its laboratories, a 6.5-ft-diam. single stage, fixed-bed, air-blown atmospheric pressure gasifier. The gasifier was coupled with a hot, raw gas combustion system and iron ore pellet in. duration kiln. The gasifier is rated at 1.5 ton/h capacity of bituminous coal.

Jan 1, 1987

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By K. Fleck

Energy West Mining Company (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, Utah. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the insitu coal strength and load transfer mechanisms for improving two-seam designs and support systems. Geologic mapping results are also used to predict local stability of headgate and tailgate entries, combining mine roof mapping, stratigraphic profiles of the coal and roof, and depth-of-cover information and dual-seam mine overlays, for use by operations personnel in planning roof and rib support for the retreating longwall sections.

Jan 1, 2012

In the spring of 1944 the Congress passed Public Law 290 (58 Stat. 190, 30 U. S. C. Sec. 321) "authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes." Section 2 reads: "In order to carry out the :purpose of this act, the Secretary of the Interior is authorized- (a) to conduct laboratory research and development work, and, with pilot plants and semi-works plants, to make careful process engineering studies, along with structural engineering studies, in order to ascertain lowest investment and operating costs necessary to determine the best demonstration plant designs and conditions of operation;

Jan 1, 1948

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962

By Anastasia M. Suchowerska

The design of effective ground support requires a sound understanding of the pre-mining state of stress in the stratum to be mined. Irregularities in the stress field encountered during multiseam mining are governed primarily by the previous mining in the surrounding strata. The aim of this study is to quantify the effects of rock mass transverse isotropy on the vertical stress redistribution in the rock strata beneath supercritical longwall panels. Wilson?s equations for determining the stress distribution induced in and beyond a single longwall panel after it has been mined have been adopted, and a plane strain finite element analysis of an elastic medium, together with the stress changes predicted by Wilson, was used to calculate the final pre-mining stresses in the underlying strata. Values of the independent shear modulus (G¢) of the rock strata, ranging from 0.1 to 1 times the isotropic shear modulus (Giso) in the plane of the strata, and a Poisson?s ratio (?) of 0.25 have been investigated. The key finding of this study is that the predicted magnitude of vertical stress in the transversely isotropic strata beneath a mined supercritical longwall panel is larger and changes more quickly with horizontal distance than is the case for an isotropic rock mass. This finding is of significance for the design of ground support measures in multi-seam mining operations.

Jan 1, 2012

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005