Search Documents

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

Burr Mineral Resource has: ?Grade / Thickness / Tonnage ?Dry Caprock ?Low Carnallite ?Low Clay / Insolubles ?Flat & Continuous Deposit ?Proper depth

May 1, 2009

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Keith Jones, Michael Francis

Contract 240 of the Channel Tunnel Rail Link comprises construction of twin4.7 km long running tunnels through a densely populated area of East London. The tunnels were constructed by EPBM in Sands and Sandy Clays, passing 4.4 m below the existing London Underground tunnels, and at depths of 20–30m below ground level beneath the Great Eastern railway lines into London Liverpool Street and a series of railway bridges and hundreds of buildings. This paper describes how the project team managed the challenges relating to the issue of settlement: mitigating settlement effects, prioritising the structures to be assessed, controlling resource expenditure by incentives and flexible response to urgent work relating to unforeseen events such as ground collapse and discovery of unusual structures.

Jan 1, 2005

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

Helium has probably aroused more varied scientific curiosity than any other single element. Discovered by spectroscopic examination of the sun during an eclipse in 1868, helium is now known to exist not only in the sun and other stars but on earth occluded in minerals, accumulated with natural gases in pockets in the earth's crust, and in the atmosphere surrounding the earth. Astronomers study its presence in the various stars of the universe for clues to their origin and history. Geochemists and geologists study its occurrences in rocks, minerals, and meteorites to determine the age of the earth and the manner of its formation. Pathologists study its effect on living tissues in search for the ideal combination with oxygen for artificial breathing mixtures in medicine, diving operations, and space vehicles. Chemists study its physical properties and use it to trace the sequence of events in reactions in which it does not participate. Geneticists and bacteriologists use it for special studies. Physicists study its behavior when liquefied and the behavior of materials cooled to nearly absolute zero by its use. Nuclear physicists learn more about the universe through study of the nuclear reactions that produce it. Through study of helium and greater knowledge of its origin and properties, science continues to unlock some of nature's more closely guarded secrets. Unknown on earth before 1895, and not discovered as a minor constituent of natural gas until 1905, helium with its simple atomic structure--a nucleus with two electrons orbiting in a closed shell--is a unique element. It is next to the lightest gas, only hydrogen is lighter. It occupies position number 2 in the Periodic Table of the Elements and heads the list of so-called "rare" or ?noble? gases. Most of the naturally occurring helium has an atomic mass of 4.003874 (oxygen = 16). A trace (1.7 x 10-5 mol percent) is the light isotope helium-3 whose atomic mass is 3.0169800 Unstable isotopes of mass numbers 5 and 6 have been authenticated. Isotopes of mass numbers 7 and 8 have been reported, but their existence is less well established. All the heavier isotopes are radioactive and are the product of nuclear reactions.

Jan 1, 1968

By L. B. Pankratz

Thermodynamic data on carbides, nitrides, and other selected substances were reviewed, evaluated, and compiled at the U.S. Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, -(G° - H298)/T, ?Hf, ?Gf, and log Kf are given in tabular form. Cp°, H° - H°248, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1994

By Michael Mann, Kenneth K. Eltschlager

The International Society of Explosives Engineers (ISEE) Standards Committee has recently updated both the Field Practice Guidelines for Blasting Seismographs and the Performance Specifications for Blasting Seismographs. The revisions are the result of public and industry input along with recommendations of the ISEE Blast Vibration and Seismograph Section. The committee is comprised of blasting seismograph manufacturers, users and general interest personnel. On an as needed basis, subject matter experts are enlisted to advise the committee. Three phases of activities are necessary for each revision cycle: request for comment on the existing standard, first draft revision of the standard based on public input, and final draft approval by the ISEE Board of Directors. The ISEE standards revision process will be explained and each standard will be discussed along with the significant revisions from the latest revision cycle.

Jan 1, 2018

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By E. Chin

The domination of Bangladesh's mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation's foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

Traditionally, capital costs of major resource development projects have been estimated as a single amount to which a percentage accuracy has been assigned based on the method of preparation of the estimate, that is, on the amount of information available to develop the estimate.However, there is a growing recognition of the importance of a probabilistic approach to capital cost estimates, and of a more rigorous calculation of estimate accuracies and of the presentation thereof. Accuracies can be expressed with more certainty as a percentage of the estimate amount where the percentage represents one standard distribution on the probability curve for the capital cost of that specific project. Thus confidence levels can be stated for various estimated amounts - for example, it can be stated that there is an 85% chance that a stated amount will not be exceeded, or a 90% certainty that a (higher) amount will not be exceeded. Moreover, the right skewness of the probability distribution curve for most projects can be readily recognised and reflected in the evaluations. This enables senior executives and board members to have a clearer understanding of investment uncertainties, and the possible magnitude of commitments.

Jan 1, 1990

By John Watson

The earliest known records related to mining document in dramatic terms the fact that mining methods have undergone significant change over the centuries. Wooden wedges, hammers and chisels, “fne setting”, to name a few, were the frst tools used to extract ore .or quarry rock for civilization. These inefficient tools and unsafe practices have been replaced today with some of the highest technology known to man. At the heart of most mining operations is the blasting program which utilizes one of the most efficient tools ever invented.. . explosives. Ever since they were invented, miners have been searching for more efficient products and methods with which to harness this “tool” and make it safer, reliable, and more eficient to use.

Jan 1, 1997

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By G Tripp, G Lorusso

The Velvet gold orebody (153 Koz Au) is located near the Kanowna Belle gold deposit in the Boorara Domain of the Kalgoorlie Terrane, a subdivision of the Archaean Eastern Goldfields Superterrane (Swager et al, 1990). Gold mineralisation at Velvet is hosted within an intrusion of intermediate composition that broadly follows a sub vertical hanging wall splay of the Fitzroy Shear Zone.Velvet was discovered in 2003 during an underground exploration drilling program targeting potential strike extensions to the Kanowna Belle deposit. Diamond drill hole KDU1595 returned a downhole intercept of 36 m grading 4.6 ppm Au approximately 500 m west of the deposit and at a vertical depth of 700 m below surface in the immediate hanging wall of the primary Kanowna Belle host structure, the Fitzroy Shear Zone. Subsequent drilling completed following the initial discovery, from both surface and underground collar positions, failed to replicate this result.In 2014, KDU1595 was resurveyed gyroscopically and the mineralised intercept correctly located. Additional drilling was undertaken to follow-up the repositioned discovery hole. Challenges included poor drilling angles through the Fitzroy Shear Zone, excessive deviation during drilling and the unknown geometry of the target. Navigational drilling helped to successfully penetrate the Fitzroy Shear Zone and in April 2015, drill hole KDU3234 returned a significant downhole intercept of 45 m grading 5.6 ppm Au.Additional drilling success resulted in a decision to develop a 600 m drive to serve as a dual-purpose access for further exploration and mining. This was a potential risk considering that the orebody geometry was unknown and all significant drilling results were clustered within a 50 m × 50 m panel. Development commenced in June 2015 and the first ore cut taken in April 2016. Geological mapping and structural interpretation, together with multi-element and spectral analysis of drill samples has enabled several other target areas to be identified for exploration. The Velvet mining area is critical to continued production at Kanowna Belle. Geological understanding must advance as mining progresses to ensure continued resource growth and optimal extraction of reserves.CITATION:Lorusso, G, Rogers, J and Tripp, G, 2017. Velvet underground exhumed – discovery and development of a new mining front at the Kanowna Belle gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Knowledge of true block grades is obtained from a mathematical model of an orebody, simulated with sample grades normally distributed and spatially correlated according io a spherical semi-variogram model.The superiority of kriging to the polygonal method of estimation is demonstrated on this modelled deposit by comparing the true values with the kriged and polygonal estimates obtained from sampling the deposit. Finally, selection of blocks of the deposit on the basis of the estimated values, shows that if kriging is used, what is predicted is largely mined, whilst if the polygonal method is used large biases can occur depending on the position of the cut-off grade.

Jan 1, 1978

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018