Search Documents

By Otto Wartenweiler

After the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities, with some decomposed andesite, while the average value of mill feed was calculated to be $20 or more in gold, no silver being present. The tonnage to be treated at the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities for increasing the capacity to 400 tons. While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to receive the run-of-mine material, which was too coarse for a No. 5 crusher. TO accomplish the coarse grinding to best advantage, a careful comparison was made between the modern steel ball-mill—the last word in crushing and grinding—and one of its older, and, at that time better-established, competitors, the rolls. The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball-mills because a simpler arrangement is possible, and because the handling of ball-mills is preferred by the operator. A marked departure was introduced for fine grinding. Instead of the long type of tube-mill, using pebbles, a mill of similar design was selected, but of much shorter length, using small cast-steel balls as grinding medium. For cyanidation, the Dorr continuous countercurrent process was

Jan 1, 1918

By A. N. Winchell

In connection with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Ringham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance. • Sandstone-limestone Gradation The sedimentary rocks of the Bingham district are chiefly sandstones, with some beds of limestone, all now lying with their strike nearly east and their dip nearly north at an angle of about 30°, near the surface. The limestone beds are remarkably irregular in thickness in some places, but usually change very slowly in composition along the strike. However, the most interesting results are obtained from a study of a section across the beds at right angles to the strike. In some places, such sections show the usual alternation of pure sandstone with nearly pure limestone, in the simple manner assumed in most geological discussions.

Jan 1, 1924

By S. F. Emmons

This mine is situated upon the western slope of the Meadow Valley mountains, about 70 miles by road from the present end of the railroad-track, which is at Uvada, on the UtahNevada boundary. This boundary-line marks fairly well a certain change in type of scenery from western Utah to eastern Nevada,—from a region in which the desert valleys predominate over the mountain ranges to one in which they are in about equal proportion. The railroad from Salt Lake City runs somewhat W. of S., for the most part along the bottom of the ancient Lake Bonneville. The latter part of its present course follows the axis of the southern arm or bay of that lake, now known as the Escalante desert. Along this bay, its line is a mathematically straight one, with no perceptible change of level for two " tangents " of more than 30 miles each, varying but a few degrees in direction. In the four or five hours re-

Jan 1, 1902

By L. O. Millard

Stockpiles in the minerals industries serve a wide variety of purposes. Usually they are for surge between stages of processing, for a dependable plant feed in anticipation of delays, or to provide for single or double shift mining in conjunction with round-the-clock milling. Often surge piles are necessary to insure a uniform feed to continuous process equipment where the material is received as an intermittent or variable flow. Extensive use is made of stockpiling for the primary purpose of blending. The significant fact about all stockpiling of bulk materials is that storing and reclaiming are two separate and distinct operations and they may present widely different problems in the selection of methods and tools.

Jan 10, 1959

By J. Szekely

A rrlethod is presented for the estitnation of oxygen pickup by teettzed molten steel streams. Of the mechanisrt~s considered for oxygen absorption, physical entrainment appeared to be the most significant. The estent of this physical entrainment may be calculated by the application of boundary layer theory. It was found that the values of oxygen pickup thus predicted were in wry good agreement with data reported in the literature, in the case of short, well-defined metal streams. This entrainment model does not provide an adequate description of oxygen pickup by long streams, exoosed to external winds and where breakup of the streatn is likely. WheN molten steel is teemed into a mold or tundish it will absorb oxygen contained in its environment. Recently interest has been expressed in the measurement and possible prediction of the extent of this oxygen absorption: this interest owes its existence to two principal factors: a) the desirability of providing a quantitative assessment of the role played by the absorbed oxygen in impairing the quality of (vacuum degassed. stainless, or continuously cast) steel; b) the need for providing guidelines for stream protection methods. The purpose of this communication is to suggest a simple method for the prediction of oxygen absorption by continuous metal streams and to compare the predicted values with the data available in the literature. It is hoped that this method may provide at least an initial framework for the interpretation of additional data that might become available. FORMULATION Consider a continuous metal stream falling into a molten metal pool as depicted in Fig. 1. This system may absorb oxygen due to the following two mechanisms: 1) physical entrainment of gases (including oxygen) into the molten pool where reactions. thus absorption, will occur; 2) mass transfer (convec:tive diffusion) of oxygen to the metal stream. 1) Physical Entrainment. The physical entrainment may be calculated by using the concept of the diaplace-ttzent tlzickness of the laminar boundary layer, which will be stated briefly in the following.&apos; When a fluid flows past a solid surface, a portion of the fluid close to the surface is retarded due to fric-tional forces. This region in which the velocity of the fluid differs from that in the main stream is called the boundary layer. An illustration of this is given in Fig. 2 where it is seen that the thickness of the boundary layer increases as we move along in the x direction. In the laminar region, when Re, < 10&apos; the thickness of the boundary layer is given by the following relationship: f =4.64 Re;1" [1] where 61 is the boundary layer thickness, x is the length along the leading edge, Us is the velocity of the free stream, (i is the viscosity of the fluid (gas in this instance).

Jan 1, 1970

By Klaus Schwerdtfeger, Hans-Jürgen Engell

Activities of silicon in Ni-Si melts have beelz determined in the temperature range 1480° to 1610°C from electromotive-force measurements involving the cells The data obtained are used to derive the activities of nickel and the integal free energies of mixing. Entropies of mixing are calculated from the free energies of mixing as obtained in the present study and the heats of mixing as available in the literature. ACTIVITIES in Fe-Si and Co-Si melts have been determined recently by the authors&apos; using galvanic cells consisting of alloy, an oxygen electrode, and an oxide melt as electrolyte. The present paper deals with activities in Ni-Si melts as measured with the same technique. A schematic diagram of the cell is shown in Fig. 1. The alloy and the electrolyte consisting of CaO and SiO2 are contained together in a silica-glass crucible. During the experiment the silica glass crystallizes to cristobalite on the surface of the crucible. Nickel contents of the electrolyte are very small (<0.1 pct as checked with chemical analysis), because of the noble character of nickel in comparison with silicon. A tapered silica tube is connected to the crucible through which a platinum or molybdenum wire is inserted, as shown in Fig. 1. A platinum tube reaches the surface of the CaO-SiO2 electrolyte from above. The platinum tube is provided with four holes on its side, through which oxygen of 1 atm pressure is blown over the electrolyte. The cell reaction is given by the equation Si(metal) + O2(gas) = SiO2(electrolyte) [3] and the galvanic electromotive force of the cell is given by the formula

Jan 1, 1965

By Robert Maddin

The application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure generallv has been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. Experimental Procedure and Results Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,&apos; were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 120° apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual x and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.³ In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig I shows the initial and final positions of the specimen axes of the crystals. At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to One another&apos; Fig 3-57 photographed On different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1949

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.&apos; The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.&apos;

Jan 1, 1964

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.&apos; Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the &apos;pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By Charles Goodale

With notes on other mines of the Marysville district by WALTER McDERMOTT, London, England, and F. L. Sizer, Dos Cabezas, Ariz. (Salt Lake Meeting, August, 1914) THE purpose of this paper is to review the history of the Drumlummon, one of the famous old mines of the West. Mining engineers, when sent to examine new mines in old districts, or to decide whether an old property, under new conditions, will pay to re-open, have had difficulty in learning anything authentic regarding workings which are under water, and historical facts about the working character of the ore, the total production, and the value of the ore with increasing depth. Not many years elapse after the pumps are pulled, before maps, books and records are destroyed, and the value of the publications of the Institute would be increased if they contained the history of many old mines now abandoned. The unsuccessful efforts of the writer quite recently in trying to obtain reliable information about a gold mine which was reported to have produced several million dollars between 1880 and 1888, the workings of which are now partially caved and under water, impressed upon his mind the desirability of having a permanent record of old properties. In this particular case, the owners insisted that under present conditions of improved methods of treatment -particularly by the use of cyanide, which was not an applied process when the mine was operated, the property. could be made to pay a handsome profit on ore left in sight in the old workings, but no assay records could be found to confirm these assurances, and even the records of bullion shipments had been destroyed. If surveys and maps were made as the work progressed, no trace of them could be found, and therefore opening of the ground through a new shaft and drifts therefrom would be attended by some risk while exploring near the old workings. Fatal accidents by flooding under these conditions have occurred, and as an evidence that miners have fears of such dangers, it was urged upon the Mining Committee during a recent session of the Montana Legislature, by a delegation of

Jan 8, 1914

By D. U. Deere, F. D. Patton

Introduction A close relationship exists between the geologic investigation and the stability analysis of the slopes of an open pit mine. One significant result of this relationship is that the stability analysis is no better than the assessment of pertinent geologic factors that enter into the analysis. In some slope stability problems the engineering solution becomes obvious once the geologic framework is established. In other cases, establishing the geologic framework is only the first stage in the process of analysis. However, even in these cases the geology should not be neglected once the analysis is made. The geology should be periodically reviewed when new slopes are excavated. This will help ensure that the basic assumptions for the analysis have not changed and will permit changes when new conditions are encountered. In recent years improved methods of stability analysis have been accompanied by advances in laboratory testing techniques and new knowledge of the shear strength of rock discontinuities. At the same time there have been improvements in field geological descriptions. As more experience is gained in analyzing and predicting the stability of rock slopes, the importance of certain geologic factors has become more apparent. Some of these factors were described in a paper given at the Open Pit Mining Symposium in Johannesburg, South Africa in September 1970 (I). This paper includes many of the points covered at that meeting but with additional emphasis on the significance of the major geologic structures. Other papers given at the South African symposium also considered geological and hydrogeological factors in slope stability analysis (2) (3) (4) (5) (6). This paper first describes the approach to a slope stability problem including assessment of the relative roles of field geology studies, laboratory testing, stability analyses, and continued slope monitoring studies. Next, is described a framework which has been found useful for classifying or separating the several types of slope stability problems encountered in open pit mines. The principal geologic factors in slope stability problems in rock are discussed and brief comments are made on how these factors distinguish stability problems in rock slopes from those normally encountered in soil slopes. The over-riding control of major geologic structures, especially faults, in most slope stability problems is emphasized. In this regard the relative importance of statistical studies is contrasted with knowledge of the positions of key structural

Jan 1, 1971

By Howard Thompson, H. N. Hall, Frank Nuss

Removal of bit cuttings is an important function of drilling muds. In an effort to obtain better understanding of the factors influencing the removal of cuttings, an extensive series of laboratory tests were made in which slip velocities of various sizes and shapes of particles were measured in muds of different physical properties. Empirical equations were then derived from these experimental data. These equations show that slip velocity is dependent on cutting size and shape, mud flow constants, and flow state of the mud. Applicability of these equations for field use is demonstrated by comparing computed slip velocities with slip velocities obtained from field tests. Drilling muds have many functions, but perhaps the most important is the removal of bit cuttings from the well. In a 10,000-ft well, the weight of rock which is drilled and must be carried to the surface is over 150 tons. In addition to this, the mud must remove any sloughings from the well bore. Failure of the mud to promptly remove either bit cuttings or sloughs from the well bore causes re-drilling and excessive wear on bit teeth, slows down drilling rate thereby increasing well costs, and greatly increases possibilities for stuck drill pipe when circulation is stopped for any length of time. Drilling muds lift bit cuttings to the surface by means of the upward velocity of the drilling mud in the annulus. Because a density difference exists between the rock being drilled and the drilling mud, there is a difference between mud velocity and the rate of bit cutting travel, called the net rise velocity. To evaluate the ability of any type of drilling mud in respect to lifting cuttings, some method must be known for predicting the rate of fall of cuttings through mud traveling upwards in the annulus. Equations for the rate of fall of particles through a true fluid have been satisfactorily determined by several authors. 1-6 Since drilling muds are not true fluids, but obey the laws of Bing-ham,7 it should not be expected that equations for rate of fall of cuttings in a true fluid would be applicable to plastic fluids such as drilling muds. Several authors have attempted to compute cutting slip velocities in muds using a viscosity value obtained with a Stormer viscosimeter; however, unsatisfactory results were obtained. Pigott8 took cognizance of the phenomenon of variation of viscosity with velocity in laminar Row, and calculated laminar slip velocities using a variable viscosity with Stokes law, and turbulent slip velocities using Rittingers law. Drilling muds obey the laws of plastic flow which involve factors not affect-

Jan 1, 1950

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome&apos; divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By Charles M. Rolker

THE Allouez Mine is situated in section 31, town 57, north of range 32 west, Michigan. The mine is being worked in a conglomerate bed, which conglomerate is generally conceded to be the continuation of the Albany and Boston conglomerate of Houghton County. Besides the well-known Calumet and Hecla with the adjoining Osceola, both working on the same bed, and the new location, the Seneca, now being tried on the Kearsarge conglomerate, the Allouez Mine is the only one working on a conglomerate bed. The Albany and Boston, in Houghton County, of which, as said before, the Allouez is supposed to be the continuation, shares with all the remaining conglomerate beds, near and around Portage Lake, the property of being non-quartziferous, while the conglomerates of Keweenaw County are all highly quartziferous in character. This change takes place, according to Professor Pumpelly, about six miles northeast of Portage Lake. The Allouez conglomerate, with a dip of 38° 15&apos; and a general course of about 36° east of north, is overlaid by a trap, and has as its footwall an amygdaloid. The trap is followed by a series of amygdaloidal melaphyres and true amygdaloids, further on by the greenstone and ashbed ; towards the lake shore alternating traps and conglomerates are found. At the footwall of the Allouez conglomerate, an amygdaloid lies, the thickness of which is not known, which is also the case with the other formations, accurate surveys and geological researches of this district having, as I was informed, never been made. About 198 meters (650 feet), horizontally measured, from the Allouez conglomerate another amygdaloid bed can be traced, on which the present rockhouse stands, further on a melaphyre is exposed, and then follow the diverse conglomerates, the Calumet, the Kearsarge, and Kingston, which, according to the last geological report, are at about the re-

Jan 1, 1877

By H. J. Hand

STATISTICAL methods are becoming increasingly important for inter-preting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of vari-ables more or less constantly tending to affect it. As pointed out by Daeves, 2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. ?

Jan 1, 1938

By P. D. P. Hamilton

In any mining district where benefication of the ores is practiced, one can usually observe several types of flow sheets even though the various producers are milling ore from the same geological formations. It is obviously impossible to describe all the mills in the Porcupine district. However, the following description of some of them is of particular interest in that it shows where one mill has paid particular attention to corduroy blanket practice; one to gravity concentration of sulfides for intensive cyanidation of the values therein contained; one to flotation of values and cyanidation of this product only; and others where small variations of standard all-slime cyanidation practice prevail. In all cases it will be seen that cyanidation is the basic principle. Discussions involving the difference in the flow sheets and the reasons for them will always be of value to those interested in the art. The author of this article, however, believes that such discussions should originate from the operators of the mills under discussion. For this reason no comparisons or discussion will be included in the description of the mills mentioned. Should any reader of this article obtain information therefrom which will be of value to him in helping to solve his own particular problems, the author will consider that the article has satisfactorily served its purpose. All values mentioned throughout this article are based on the value of gold at $20.67 per ounce. Coniaurum Mines, Limited The ore of the Coniaurium mines consists of a mineralized schist and quartz containing about 2.5 per cent sulfides. Owing to the low grade of ore developed in the mine, extreme care has had to be exercised throughout the entire mining and milling operation in order that an operating profit might be obtained. The management, however, has been able to keep costs down, with the result that at present the outlook for the property is considerably brighter than it has been in the past. This is partly due to the fact that it is now known how to mine and treat

Jan 1, 1935

By Howard A. Smith

Of late considerable experimental and theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure formation and in age-hardening systems. Most of the work has been confined to ferrous alloy1-9† although two investigations have been made on copper alloys10*". That such work may be of considerable practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut fur Eisen-for~chung&apos;13, 14, and by the everyday use of precipitation and age-hardening principles15. Experiments in this country have generally followed Davenport and Bain&apos;s technique of rapid supercooling followed by isothermal treatment. In Germany16, 17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At suberitical temperatures above Ar" (temperature of martensite formation) where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Davenport and Bain&apos; find that different sorts of atoms in solid solution in gamma iron affect the length of this " prereaction" period differently, manganese probably being the most effective in lengthening it. It is very difficult to believe that nothing occurs within these "prereaction" regions, for if this were so there is no reason why any reaction at all should be observed. In the light of experimental facts and theoretical considerations it is certainly

Jan 1, 1935

By Edward B. Hughes, Frank G. Norris

OXIDATION is characteristic of all processes for making steel from pig iron. This thought has been aptly expressed by H. W. Graham13 in the most recent Howe Memorial Lecture, "The process of steel-making consists of using iron oxide to reduce the carbon content of the pig iron to the desired level." Direct oxidation refers to the reaction that results from introducing oxygen either alone or mixed with other gases directly into the steel bath. In working a heat, oxygen in some form is added to the steel to remove the undesirable constituents as oxides. There are two general methods of supplying this oxygen to the open hearth bath. The method in which the oxygen is added as a, compound such as C02-or iron ore is designated an indirect method because the steel bath must first decompose the compound to attain oxygen in a usable form. The other method in which oxygen is added to the bath in the elemental or gaseous form, more or less diluted by other gases such as nitrogen, is a direct, method because no decomposition is necessary before the oxygen reacts with iron to form FeO which is dissolved in the bath in a usable form. Bubble formation (at least of a macroscopic size) presents no problem in case of direct oxidation because the reacting agent (oxygen) is in the form of bubbles when entering the metal. Regardless of whether oxygen is introduced into the bath directly or indirectly, several reactions proceed concurrently. In the presence of the bath of molten iron, FeO is formed either by oxidation of iron by oxygen or reduction of oxides by iron. This FeO dissolved in the molten iron is the source of oxygen for the oxidation of manganese, carbon, silicon, and phosphorus if these are present. The oxidation of carbon from steel is the controlling steelmaking reaction. The introduction of oxygen into the bath, its reaction in the elimination of impurities, and its control by the use of de-oxidizing additions have been subjects of importance since steel was first made by the bessemer process. Direct oxidation is, in a sense, an application of the bessemer principle to the open hearth process. Graham13 states: "The use of oxygen or air jets introduced into the metal bath is essentially an effort to approach in the open hearth the turbulence, rapid interface reaction, and high production rate per hour that exists in the bessemer process." The general subject, "Oxygen in Steelmaking," was given new life by the studies of Herty and associates starting about1925. The current interest in elemental oxygen is intimately related to the large scale production of oxygen developed during the war period. Some of the first applications were made during the early summer of 1946 at the Steel Co. of Canada using oxygen with the fuel. Such a use is of considerable interest and importance in contributing to faster heats but is not the subject of the present discussion which deals entirely with the introduction of elemental oxygen directly into the open hearth bath. A recent article12 reviewing the current

Jan 1, 1948

By C. D. Woodward

ThE subject of elcctric signals for the despatching of mining cagey through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is rcliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised; when ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender&apos;s use, two signal systems are installed in cach hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC " or station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shaft bells, takes its energy from closed-circuit primary batteries. As a supplemcnt to the two main signals, a buzzer system is installed The general arrangement is similar to the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers arc operated, thus notifying the station tender that he is wanted at seine particular level. Placed on the station posts, and within easy reach of the men on the cages are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. I, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 1, 1923